Is the cx25840 module loaded? I see no reference to it. If it is loaded
then I'd say you have problems with the cx25840 chip and I recommend
testing it on another machine first.
Hans
On Saturday 10 June 2006 21:47, Greg Woods wrote:
> On Wed, 2006-06-07 at 08:04 +0200, Hans Verkuil wrote:
> > Please download the 0.6.3 dev. snapshot here:
> > http://ivtvdriver.org/viewcvs/ivtv/branches/0.6.tar.gz?view=tar
> >
> > Now add the 'newi2c=0' ivtv module option and try again. Let me
> > know if this fixes your problems.
>
> Unfortunately, it did not. I presume that the latter statement is
> accomplished by having this line in /etc/modprobe.conf:
>
> options ivtv newi2c=0
>
>
>
> ivtv: ==================== START INIT IVTV ====================
> ivtv: version 0.6.3 (development snapshot compiled on Sat 10 Jun
> 2006 01:33:42
> PM MDT) loading
> ivtv: Linux version: 2.6.16-1.2122_FC5 686 REGPARM 4KSTACKS gcc-4.1
> ivtv: In case of problems please include the debug info between
> ivtv: the START INIT IVTV and END INIT IVTV lines, along with
> ivtv: any module options, when mailing the ivtv-users mailinglist.
> ivtv0: Autodetected Hauppauge WinTV PVR-150 card (cx23416 based)
> ACPI: PCI Interrupt 0000:02:0e.0[A] -> GSI 17 (level, low) -> IRQ 18
> tveeprom 0-0050: Hauppauge model 26032, rev C199, serial# 8125669
> tveeprom 0-0050: tuner model is TCL 2002N 5H (idx 99, type 50)
> tveeprom 0-0050: TV standards NTSC(M) (eeprom 0x08)
> tveeprom 0-0050: audio processor is CX25841 (idx 35)
> tveeprom 0-0050: decoder processor is CX25841 (idx 28)
> tveeprom 0-0050: has no radio, has IR remote
> tuner 0-0061: chip found @ 0xc2 (ivtv i2c driver #0)
> wm8775 0-001b: chip found @ 0x36 (ivtv i2c driver #0)
> ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver
> (PCI)
> cs: IO port probe 0x100-0x3af: excluding 0x170-0x177 0x370-0x377
> cs: IO port probe 0x3e0-0x4ff: excluding 0x408-0x40f 0x4d0-0x4d7
> cs: IO port probe 0x820-0x8ff: excluding 0x830-0x837
> cs: IO port probe 0xc00-0xcf7: excluding 0xc00-0xc07 0xc10-0xc17
> 0xc50-0xc57 0xc68-0xc6f 0xcd0-0xcd7
> cs: IO port probe 0xa00-0xaff: clean.
> ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes)
> ieee1394: Initialized config rom entry `ip1394'
> ivtv0: Encoder revision: 0x02050032
> ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB
> total)
> ivtv0: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB
> total)
> ivtv0: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB
> total)
> ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers
> (2048KB total)
> tuner 0-0061: type set to 50 (TCL 2002N)
> ivtv0: i2c hardware 0x00000001 not found for command 0xc008561c!
> ivtv0: i2c addr 0x44 not found for command 0x40045613!
> ivtv0: i2c addr 0x44 not found for command 0xc0045627!
> ivtv0: i2c addr 0x44 not found for command 0x40345622!
> ivtv0: i2c addr 0x44 not found for command 0x40045612!
> ivtv0: i2c hardware 0x00000001 not found for command 0xc008561c!
> ivtv0: i2c hardware 0x00000001 not found for command 0xc008561c!
> ivtv0: i2c addr 0x44 not found for command 0x40045613!
> ivtv0: i2c addr 0x44 not found for command 0x40045612!
> ivtv0: i2c hardware 0x00000001 not found for command 0xc008561c!
> ivtv0: Initialized Hauppauge WinTV PVR-150, card #0
> ivtv: ==================== END INIT IVTV ====================
>
> And once again, cat /dev/video0 > file.mpg yields an empty file.
>
> --Greg
>
>
>
>
> _______________________________________________
> ivtv-users mailing list
> [email protected]
> http://ivtvdriver.org/mailman/listinfo/ivtv-users
_______________________________________________
ivtv-users mailing list
[email protected]
http://ivtvdriver.org/mailman/listinfo/ivtv-users
