Hello! I have used a PVR-150 about half a year now under Fedora Core 5 - and it has been working happily. After a power failure a couple of days ago the machine got rebooted (it had about 100 days uptime), so i decided to install a new kernel. Yum grabbed a new ivtv, i rebooted the machine, and everything seemed OK.
That was, until i tried to test the TV-card, as i have heard that the new kernel/ivtv should have fixed the "low color saturation" problem (has it?). So i ran "mplayer /dev/video0", and got only static (as expected), and then used "ivtv-tune -t europe-west -c E8" to tune the card. Got this response: "/dev/video0: 196.250 MHz" - but no signal detected. And only static... What happened? Grepped from yum.log: Dec 15 13:33:39 Updated: ivtv.i386 1:0.8.2-123.fc5.at Dec 15 13:33:45 Installed: ivtv-kmdl-2.6.18-1.2239.fc5.i686 1:0.8.2-123.fc5.at Dec 15 13:34:18 Erased: ivtv-kmdl-2.6.17-1.2157_FC5 Dec 15 13:34:34 Erased: ivtv-kmdl-2.6.17-1.2157_FC5smp Dec 15 13:47:02 Installed: ivtv-kmdl-2.6.18-1.2239.fc5smp.i686 1:0.8.2-123.fc5.at (i use the smp kernel to get hyper-threading on intel p4) dmesg output: [EMAIL PROTECTED] log]# dmesg | tac | > sed -n '/=\ \ END INIT IVTV\ \ =/,/= START INIT IVTV =/p; > /= START INIT IVTV =/q' | > tac ivtv: ==================== START INIT IVTV ==================== ivtv: version 0.8.2 (tagged release) loading ivtv: Linux version: 2.6.18-1.2239.fc5smp SMP mod_unload 686 REGPARM 4KSTACKS gcc-4.1 ivtv: In case of problems please include the debug info between ivtv: the START INIT IVTV and END INIT IVTV lines, along with ivtv: any module options, when mailing the ivtv-users mailinglist. e100: eth1: e100_probe: addr 0xb9ddf000, irq 74, MAC addr 00:90:27:BE:5F:06 hda_codec: Unknown model for ALC882, trying auto-probe from BIOS... ivtv0: Autodetected Hauppauge card (cx23416 based) ACPI: PCI Interrupt 0000:01:02.0[A] -> GSI 22 (level, low) -> IRQ 217 usb 1-1: new low speed USB device using uhci_hcd and address 4 usb 1-1: configuration #1 chosen from 1 choice input: Logitech USB Receiver as /class/input/input3 input: USB HID v1.10 Mouse [Logitech USB Receiver] on usb-0000:00:1d.0-1 usb 2-2: new full speed USB device using uhci_hcd and address 2 ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes) tveeprom 1-0050: Hauppauge model 26559, rev F089, serial# 9316023 tveeprom 1-0050: tuner model is TCL MFPE05 2 (idx 89, type 38) tveeprom 1-0050: TV standards PAL(B/G) PAL(I) SECAM(L/L') PAL(D/D1/K) (eeprom 0x74) tveeprom 1-0050: audio processor is CX25843 (idx 37) tveeprom 1-0050: decoder processor is CX25843 (idx 30) tveeprom 1-0050: has radio, has no IR remote ivtv0: Autodetected Hauppauge WinTV PVR-150 tuner 1-0043: chip found @ 0x86 (ivtv i2c driver #0) tda9887 1-0043: tda988[5/6/7] found @ 0x43 (tuner) tuner 1-0061: chip found @ 0xc2 (ivtv i2c driver #0) cx25840 1-0044: cx25843-23 found @ 0x88 (ivtv i2c driver #0) usb 2-2: configuration #1 chosen from 1 choice Bluetooth: Core ver 2.10 NET: Registered protocol family 31 Bluetooth: HCI device and connection manager initialized Bluetooth: HCI socket layer initialized Bluetooth: HCI USB driver ver 2.9 usbcore: registered new driver hci_usb cx25840 1-0044: loaded v4l-cx25840.fw firmware (16382 bytes) wm8775 1-001b: chip found @ 0x36 (ivtv i2c driver #0) ivtv0: Encoder revision: 0x02050032 ivtv0: Registered device video0 for encoder MPEG ivtv0: Registered device video32 for encoder YUV ivtv0: Registered device vbi0 for encoder VBI ivtv0: Registered device video24 for encoder PCM audio ivtv0: Registered device radio0 for encoder radio tuner 1-0061: type set to 38 (Philips PAL/SECAM multi (FM1216ME MK3)) ivtv0: Initialized Hauppauge WinTV PVR-150, card #0 ivtv: ==================== END INIT IVTV ==================== A quick grep shows that the tuner type is set (unlike what happened to http://www.gossamer-threads.com/lists/ivtv/users/33280#33280 ): [EMAIL PROTECTED] log]# dmesg | tac | sed -n '/=\ \ END INIT IVTV\ \ =/,/= START INIT IVTV =/p; /= START INIT IVTV =/q' | tac | grep tuner tveeprom 1-0050: tuner model is TCL MFPE05 2 (idx 89, type 38) tuner 1-0043: chip found @ 0x86 (ivtv i2c driver #0) tda9887 1-0043: tda988[5/6/7] found @ 0x43 (tuner) tuner 1-0061: chip found @ 0xc2 (ivtv i2c driver #0) tuner 1-0061: type set to 38 (Philips PAL/SECAM multi (FM1216ME MK3)) Anyone who knows what is wrong? --- Kyrre _______________________________________________ ivtv-users mailing list [email protected] http://ivtvdriver.org/mailman/listinfo/ivtv-users
