Andrew Berry wrote: > On 4-Feb-07, at 3:46 AM, Rudy Zijlstra wrote: > >> Andrew Berry wrote: >>> [17181533.444000] ivtv: any module options, when mailing the >>> ivtv-users mailinglist. >> ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ >> Did you read this? > > I'm not doing anything beyond 'modprobe ivtv'. > >> I am missing in the above: >> - eeprom read-out messages, >> - tuner messages >> - .... > > Sorry, I didn't realize that there were lines not labelled as 'ivtv'. > > Thanks, > --Andrew > > [17181533.444000] ivtv: ==================== START INIT IVTV > ==================== > [17181533.444000] ivtv: version 0.7.3 (tagged release) loading > [17181533.444000] ivtv: Linux version: 2.6.17-10-generic SMP > mod_unload 586 REGPARM gcc-4.1 > [17181533.444000] ivtv: In case of problems please include the debug > info between > [17181533.444000] ivtv: the START INIT IVTV and END INIT IVTV lines, > along with > [17181533.444000] ivtv: any module options, when mailing the > ivtv-users mailinglist. > [17181533.444000] ivtv0: Autodetected Hauppauge WinTV PVR-350 card > (cx23415 based) > [17181533.448000] ACPI: PCI Interrupt 0000:01:07.0[A] -> Link [APC2] > -> GSI 17 (level, low) -> IRQ 58 > [17181533.668000] saa7115 2-0021: saa7115 found @ 0x42 (ivtv i2c > driver #0) > [17181533.812000] saa7127 2-0044: saa7127 found @ 0x88 (ivtv i2c > driver #0) > [17181533.828000] lirc_i2c: chip found @ 0x18 (Hauppauge IR) > [17181533.828000] lirc_dev: lirc_register_plugin: sample_rate: 10 > [17181533.908000] tveeprom 2-0050: Hauppauge model 48132, rev J323, > serial# 7012185 > [17181533.908000] tveeprom 2-0050: tuner model is Philips FM1236 (idx > 23, type 2) > [17181533.908000] tveeprom 2-0050: TV standards NTSC(M) (eeprom 0x08) > [17181533.908000] tveeprom 2-0050: audio processor is MSP4448 (idx 27) > [17181533.908000] tveeprom 2-0050: decoder processor is SAA7115 (idx 19) > [17181533.908000] tveeprom 2-0050: has radio, has IR remote > [17181534.544000] ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 > bytes) > [17181534.560000] ivtv0: loaded v4l-cx2341x-dec.fw firmware (262144 > bytes) > [17181534.784000] ivtv0: Encoder revision: 0x02050032 > [17181534.792000] ivtv0: Decoder revision: 0x02020023 > [17181534.792000] ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 > buffers (4096KB total) > [17181534.792000] ivtv0: Allocate DMA encoder YUV stream: 194 x 10800 > buffers (2048KB total) > [17181534.792000] ivtv0: Allocate DMA encoder VBI stream: 120 x 17472 > buffers (2048KB total) > [17181534.792000] ivtv0: Allocate DMA encoder PCM audio stream: 455 x > 4608 buffers (2048KB total) > [17181534.792000] ivtv0: Create encoder radio stream > [17181534.792000] ivtv0: Allocate DMA decoder MPEG stream: 16 x 65536 > buffers (1024KB total) > [17181534.792000] ivtv0: Allocate DMA decoder VBI stream: 512 x 2048 > buffers (1024KB total) > [17181534.796000] ivtv0: Create decoder VOUT stream > [17181534.796000] ivtv0: Allocate DMA decoder YUV stream: 24 x 43200 > buffers (1024KB total) > [17181534.864000] ivtv0: loaded v4l-cx2341x-init.mpg firmware (155648 > bytes) > [17181534.972000] ivtv0: i2c hardware 0x00000008 not found for command > 0xc008561c! > [17181534.976000] ivtv0: i2c hardware 0x00000008 not found for command > 0x4008646d! > [17181534.976000] ivtv0: i2c hardware 0x00000008 not found for command > 0xc008561c! > [17181534.984000] ivtv0: i2c hardware 0x00000008 not found for command > 0xc008561c! > [17181534.984000] ivtv0: i2c hardware 0x00000008 not found for command > 0xc008561c! > [17181534.984000] ivtv0: Initialized Hauppauge WinTV PVR-350, card #0 > [17181534.984000] ivtv: ==================== END INIT IVTV > ==================== Your tuner is not getting initialized. That is why you get black video. What does lsmod say? Have you enabled automatic loading of modules in the kernel? Do you can without that, but than you have to know and load all modules by hand before loading ivtv.
_______________________________________________ ivtv-users mailing list [email protected] http://ivtvdriver.org/mailman/listinfo/ivtv-users
