Hi, I was trying to install my new Hauppauge 150 l.p. Card on my Linux-machine. Everything is cool until I try to get a video via "cat /dev/video0 >> /var/tmp/tmp.mpg". This results in a 0-byte-file and I am getting the following messages in my kernel-log:
May 8 03:21:32 media ivtv0: i2c addr 0x44 not found for command 0xc0cc5605! I am using Archlinux with Kernel 2.6.21, ivtv 0.10.1. This is my startup-log: ivtv: ==================== START INIT IVTV ==================== ivtv: version 0.10.1 (tagged release) loading ivtv: Linux version: 2.6.21-ARCH SMP preempt mod_unload 686 ivtv: In case of problems please include the debug info between ivtv: the START INIT IVTV and END INIT IVTV lines, along with ivtv: any module options, when mailing the ivtv-users mailinglist. ivtv0: Autodetected Hauppauge card (cx23416 based) ACPI: PCI Interrupt 0000:00:0f.0[A] -> GSI 18 (level, low) -> IRQ 16 ivtv0: loaded v4l-cx2341x-enc.fw firmware (376836 bytes) ivtv0: Encoder revision: 0x02060039 tveeprom 1-0050: Hauppauge model 30039, rev B157, serial# 6817533 tveeprom 1-0050: tuner model is Philips FM1216 ME MK3 (idx 57, type 38) tveeprom 1-0050: TV standards PAL(B/G) PAL(I) SECAM(L/L') PAL(D/D1/K) (eeprom 0x74) tveeprom 1-0050: audio processor is MSP4418 (idx 25) tveeprom 1-0050: decoder processor is SAA7115 (idx 19) tveeprom 1-0050: has radio, has no IR receiver, has no IR transmitter ivtv0: Unknown model 30039, defaulting to PVR-150 ivtv0: Autodetected Hauppauge WinTV PVR-150 tuner 1-0043: chip found @ 0x86 (ivtv i2c driver #0) tda9887 1-0043: tda988[5/6/7] found @ 0x43 (tuner) tuner 1-0061: chip found @ 0xc2 (ivtv i2c driver #0) ivtv0: Registered device video0 for encoder MPEG (4 MB) ivtv0: Registered device video32 for encoder YUV (2 MB) ivtv0: Registered device vbi0 for encoder VBI (1 MB) ivtv0: Registered device video24 for encoder PCM audio (1 MB) ivtv0: Registered device radio0 for encoder radio tuner 1-0061: type set to 38 (Philips PAL/SECAM multi (FM1216ME MK3)) ivtv0: i2c hardware 0x00000001 (cx2584x) not found for command 0xc008561c! ivtv0: i2c addr 0x44 not found for command 0x4008646f! ivtv0: i2c hardware 0x00000020 (wm8775) not found for command 0x4008646d! ivtv0: i2c hardware 0x00000001 (cx2584x) not found for command 0x4008646d! ivtv0: i2c hardware 0x00000001 (cx2584x) not found for command 0xc008561c! ivtv0: i2c hardware 0x00000001 (cx2584x) not found for command 0xc008561c! ivtv0: i2c hardware 0x00000001 (cx2584x) not found for command 0xc008561c! ivtv0: Initialized Hauppauge WinTV PVR-150, card #0 ivtv: ==================== END INIT IVTV ==================== lspci: lspci: 00:0f.0 Multimedia video controller: Internext Compression Inc iTVC16 (CX23416) MPEG-2 Encoder (rev 01) Kernel: CONFIG_VIDEO_WM8775=m, CONFIG_VIDEO_CX25840=m It is the same mysterious thing with Ubuntu 7.04 on the same computer. I tried another Computer with a running Windows XP, installed the card and the Hauppauge drivers and it worked. So the card is obviously not defect. Finally I managed to get it work with an old version of the software: I used as distribution c't vdr, which has an 2.6.16-kernel and ivtv 0.6.x. Everything works fine, I can switch channels and record everything to an mpg file. There seems to be a problem with this card in the newest repository. Here the log-messages for this working configuration: ivtv: ==================== START INIT IVTV ==================== ivtv: version 0.6.1 (tagged release) loading ivtv: Linux version: 2.6.16-ct-1 586 gcc-3.3 ivtv: In case of problems please include the debug info between ivtv: the START INIT IVTV and END INIT IVTV lines, along with ivtv: any module options, when mailing the ivtv-users mailinglist. input: PS2++ Logitech Wheel Mouse as /class/input/input2 ivtv0: Autodetected Hauppauge WinTV PVR-250 card (cx23416 based) ACPI: PCI Interrupt 0000:00:0e.0[A] -> GSI 17 (level, low) -> IRQ 193 tveeprom 1-0050: Hauppauge model 30039, rev B157, serial# 6817533 tveeprom 1-0050: tuner model is Philips FM1216 ME MK3 (idx 57, type 38) tveeprom 1-0050: TV standards PAL(B/G) PAL(I) SECAM(L/L') PAL(D/D1/K) (eeprom 0x74) tveeprom 1-0050: audio processor is MSP4418 (idx 25) tveeprom 1-0050: decoder processor is SAA7115 (idx 19) tveeprom 1-0050: has radio, has no IR remote tuner 1-0061: chip found @ 0xc2 (ivtv i2c driver #0) tda9887 1-0043: chip found @ 0x86 (ivtv i2c driver #0) saa7115 1-0021: saa7115 found @ 0x42 (ivtv i2c driver #0) msp3400 1-0040: MSP4418G-A2 found @ 0x80 (ivtv i2c driver #0) msp3400 1-0040: MSP4418G-A2 supports nicam and radio, mode is autodetect and autoselect ts: Compaq touchscreen protocol output ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes) ivtv0: Encoder revision: 0x02060039 ivtv0 warning: Encoder Firmware can be buggy, use version 0x02040011, 0x02040024 or 0x02050032. ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total) ivtv0: Allocate DMA encoder YUV stream: 161 x 12960 buffers (2048KB total) ivtv0: Allocate DMA encoder VBI stream: 80 x 26208 buffers (2048KB total) ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB total) ivtv0: Create encoder radio stream tuner 1-0061: type set to 38 (Philips PAL/SECAM multi (FM1216ME MK3)) ivtv0: Initialized Hauppauge WinTV PVR-250, card #0 ivtv: ==================== END INIT IVTV ==================== I am wondering why he is initializing here a WinTV PVR-250 card. Another thing in the first log is the line ivtv0: Unknown model 30039, defaulting to PVR-150. Perhaps here is a problem? Does anybody have a clue why this problem occurs? Any settings I might have missed? Thanks, Stefan _______________________________________________ ivtv-users mailing list [email protected] http://ivtvdriver.org/mailman/listinfo/ivtv-users
