On 5/10/07, Stefan Langeland <[EMAIL PROTECTED]> wrote: > Sander Sweers wrote: > > On di, 2007-05-08 at 19:57 +0200, [EMAIL PROTECTED] wrote: > >> Hi, > >> > >> I was trying to install my new Hauppauge 150 l.p. Card on my > >> Linux-machine. Everything is cool until I try to get a video via "cat > >> /dev/video0 >> /var/tmp/tmp.mpg". This results in a 0-byte-file and I am > >> getting the following messages in my kernel-log: > > > > It looks like this is a special halve height (low profile) card as you > > mention L.P. in the subject? This is not a PVR-150 but a PVR-250. > > You are right; it is a Low profile card, I forgot to mention. Thanks for the > hint that I have a 250 > card, I didn't know :) > > >> May 8 03:21:32 media ivtv0: i2c addr 0x44 not found for command > >> 0xc0cc5605! > > > > These errors indeed are the problem. > > > > You definately need the following modules enabled or installed. > > > > * Conexant CX2341x MPEG encoders (CONFIG_VIDEO_CX2341X) > > * Philips SAA7113/4/5 video decoders (CONFIG_VIDEO_SAA711X) > > * Micronas MSP34xx audio decoders (CONFIG_VIDEO_MSP3400) > These modules are in the standard ubuntu-kernel included as modules and are > also loaded > > > Can you try and force the card type to a PVR-250 by passing cardtype=1 > > to ivtv? > > > I am using Ubuntu 7.04 now; rmmoded all modules down to rmmod i2c_core. Then > I typed modprobe ivtv > cardtype=1. But it is not working yet: > > [ 1507.568787] ivtv0: Removed Hauppauge WinTV PVR-150, card #0 > [ 1590.329400] ivtv: ==================== START INIT IVTV > ==================== > [ 1590.329408] ivtv: version 0.10.1 (tagged release) loading > [ 1590.329410] ivtv: Linux version: 2.6.20-15-generic SMP mod_unload 586 > [ 1590.329413] ivtv: In case of problems please include the debug info > between > [ 1590.329415] ivtv: the START INIT IVTV and END INIT IVTV lines, along with > [ 1590.329417] ivtv: any module options, when mailing the ivtv-users > mailinglist. > [ 1590.330536] ivtv0: User specified Hauppauge WinTV PVR-250 card (detected > cx23416 based chip) > [ 1590.330761] ACPI: PCI Interrupt 0000:00:0e.0[A] -> GSI 17 (level, low) -> > IRQ 18 > [ 1590.974489] ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes) > [ 1591.189298] ivtv0: Encoder revision: 0x02050032 > [ 1591.189304] ivtv0: Recommended firmware version is 0x02060039. > [ 1591.259071] tveeprom 0-0050: Hauppauge model 30039, rev B157, serial# > 6817533 > [ 1591.259080] tveeprom 0-0050: tuner model is Philips FM1216 ME MK3 (idx 57, > type 38) > [ 1591.259084] tveeprom 0-0050: TV standards PAL(B/G) PAL(I) SECAM(L/L') > PAL(D/D1/K) (eeprom 0x74) > [ 1591.259088] tveeprom 0-0050: audio processor is MSP4418 (idx 25) > [ 1591.259091] tveeprom 0-0050: decoder processor is SAA7115 (idx 19) > [ 1591.259094] tveeprom 0-0050: has radio, has no IR receiver, has no IR > transmitter > [ 1591.259098] ivtv0: Unknown model 30039, defaulting to PVR-150 > [ 1591.259103] ivtv0: Autodetected Hauppauge WinTV PVR-150 > [ 1591.273115] tuner 0-0043: chip found @ 0x86 (ivtv i2c driver #0) > [ 1591.273168] tda9887 0-0043: tda988[5/6/7] found @ 0x43 (tuner) > [ 1591.277480] tuner 0-0061: chip found @ 0xc2 (ivtv i2c driver #0) > [ 1591.324361] ivtv0: Registered device video0 for encoder MPEG (4 MB) > [ 1591.324726] ivtv0: Registered device video32 for encoder YUV (2 MB) > [ 1591.325064] ivtv0: Registered device vbi0 for encoder VBI (1 MB) > [ 1591.325354] ivtv0: Registered device video24 for encoder PCM audio (1 MB) > [ 1591.325756] ivtv0: Registered device radio0 for encoder radio > [ 1591.325868] tuner 0-0061: type set to 38 (Philips PAL/SECAM multi > (FM1216ME MK3)) > [ 1591.325978] ivtv0: i2c hardware 0x00000001 (cx2584x) not found for command > 0xc008561c! > [ 1591.325985] ivtv0: i2c addr 0x44 not found for command 0x4008646f! > [ 1591.325990] ivtv0: i2c hardware 0x00000020 (wm8775) not found for command > 0x4008646d! > [ 1591.325993] ivtv0: i2c hardware 0x00000001 (cx2584x) not found for command > 0x4008646d! > [ 1591.440825] ivtv0: i2c hardware 0x00000001 (cx2584x) not found for command > 0xc008561c! > [ 1591.443804] ivtv0: i2c hardware 0x00000001 (cx2584x) not found for command > 0xc008561c! > [ 1591.580714] ivtv0: i2c hardware 0x00000001 (cx2584x) not found for command > 0xc008561c! > [ 1591.580725] ivtv0: Initialized Hauppauge WinTV PVR-150, card #0 > [ 1591.580955] ivtv: ==================== END INIT IVTV > ==================== > > He set it to WinTV PVR-250, but then says again that he finds an unknown > model and goes back to his > default PVR-150. Any other idea? > I may be wrong but it looks like a few needed modules are not loaded. # lsmod | grep wm8775
John _______________________________________________ ivtv-users mailing list [email protected] http://ivtvdriver.org/mailman/listinfo/ivtv-users
