On di, 2007-05-08 at 19:57 +0200, [EMAIL PROTECTED] wrote: > Hi, > > I was trying to install my new Hauppauge 150 l.p. Card on my Linux-machine. > Everything is cool until I try to get a video via "cat /dev/video0 >> > /var/tmp/tmp.mpg". This results in a 0-byte-file and I am getting the > following messages in my kernel-log:
It looks like this is a special halve height (low profile) card as you mention L.P. in the subject? This is not a PVR-150 but a PVR-250. > May 8 03:21:32 media ivtv0: i2c addr 0x44 not found for command 0xc0cc5605! These errors indeed are the problem. You definately need the following modules enabled or installed. * Conexant CX2341x MPEG encoders (CONFIG_VIDEO_CX2341X) * Philips SAA7113/4/5 video decoders (CONFIG_VIDEO_SAA711X) * Micronas MSP34xx audio decoders (CONFIG_VIDEO_MSP3400) Can you try and force the card type to a PVR-250 by passing cardtype=1 to ivtv? Greets Sander > This is my startup-log: > > ivtv: ==================== START INIT IVTV ==================== > ivtv: version 0.10.1 (tagged release) loading > ivtv: Linux version: 2.6.21-ARCH SMP preempt mod_unload 686 > ivtv: In case of problems please include the debug info between > ivtv: the START INIT IVTV and END INIT IVTV lines, along with > ivtv: any module options, when mailing the ivtv-users mailinglist. > ivtv0: Autodetected Hauppauge card (cx23416 based) > ACPI: PCI Interrupt 0000:00:0f.0[A] -> GSI 18 (level, low) -> IRQ 16 > ivtv0: loaded v4l-cx2341x-enc.fw firmware (376836 bytes) > ivtv0: Encoder revision: 0x02060039 > tveeprom 1-0050: Hauppauge model 30039, rev B157, serial# 6817533 > tveeprom 1-0050: tuner model is Philips FM1216 ME MK3 (idx 57, type 38) > tveeprom 1-0050: TV standards PAL(B/G) PAL(I) SECAM(L/L') PAL(D/D1/K) (eeprom > 0x74) > tveeprom 1-0050: audio processor is MSP4418 (idx 25) > tveeprom 1-0050: decoder processor is SAA7115 (idx 19) > tveeprom 1-0050: has radio, has no IR receiver, has no IR transmitter > ivtv0: Unknown model 30039, defaulting to PVR-150 > ivtv0: Autodetected Hauppauge WinTV PVR-150 > tuner 1-0043: chip found @ 0x86 (ivtv i2c driver #0) > tda9887 1-0043: tda988[5/6/7] found @ 0x43 (tuner) > tuner 1-0061: chip found @ 0xc2 (ivtv i2c driver #0) > ivtv0: Registered device video0 for encoder MPEG (4 MB) > ivtv0: Registered device video32 for encoder YUV (2 MB) > ivtv0: Registered device vbi0 for encoder VBI (1 MB) > ivtv0: Registered device video24 for encoder PCM audio (1 MB) > ivtv0: Registered device radio0 for encoder radio > tuner 1-0061: type set to 38 (Philips PAL/SECAM multi (FM1216ME MK3)) > ivtv0: i2c hardware 0x00000001 (cx2584x) not found for command 0xc008561c! > ivtv0: i2c addr 0x44 not found for command 0x4008646f! > ivtv0: i2c hardware 0x00000020 (wm8775) not found for command 0x4008646d! > ivtv0: i2c hardware 0x00000001 (cx2584x) not found for command 0x4008646d! > ivtv0: i2c hardware 0x00000001 (cx2584x) not found for command 0xc008561c! > ivtv0: i2c hardware 0x00000001 (cx2584x) not found for command 0xc008561c! > ivtv0: i2c hardware 0x00000001 (cx2584x) not found for command 0xc008561c! > ivtv0: Initialized Hauppauge WinTV PVR-150, card #0 > ivtv: ==================== END INIT IVTV ==================== > > > lspci: > > lspci: 00:0f.0 Multimedia video controller: Internext Compression Inc iTVC16 > (CX23416) MPEG-2 Encoder (rev 01) > > Kernel: CONFIG_VIDEO_WM8775=m, CONFIG_VIDEO_CX25840=m > > It is the same mysterious thing with Ubuntu 7.04 on the same computer. I > tried another Computer with a running Windows XP, installed the card and the > Hauppauge drivers and it worked. So the card is obviously not defect. > > Finally I managed to get it work with an old version of the software: I used > as distribution c't vdr, which has an 2.6.16-kernel and ivtv 0.6.x. > Everything works fine, I can switch channels and record everything to an mpg > file. > There seems to be a problem with this card in the newest repository. > > Here the log-messages for this working configuration: > > ivtv: ==================== START INIT IVTV ==================== > ivtv: version 0.6.1 (tagged release) loading > ivtv: Linux version: 2.6.16-ct-1 586 gcc-3.3 > ivtv: In case of problems please include the debug info between > ivtv: the START INIT IVTV and END INIT IVTV lines, along with > ivtv: any module options, when mailing the ivtv-users mailinglist. > input: PS2++ Logitech Wheel Mouse as /class/input/input2 > ivtv0: Autodetected Hauppauge WinTV PVR-250 card (cx23416 based) > ACPI: PCI Interrupt 0000:00:0e.0[A] -> GSI 17 (level, low) -> IRQ 193 > tveeprom 1-0050: Hauppauge model 30039, rev B157, serial# 6817533 > tveeprom 1-0050: tuner model is Philips FM1216 ME MK3 (idx 57, type 38) > tveeprom 1-0050: TV standards PAL(B/G) PAL(I) SECAM(L/L') PAL(D/D1/K) (eeprom > 0x74) > tveeprom 1-0050: audio processor is MSP4418 (idx 25) > tveeprom 1-0050: decoder processor is SAA7115 (idx 19) > tveeprom 1-0050: has radio, has no IR remote > tuner 1-0061: chip found @ 0xc2 (ivtv i2c driver #0) > tda9887 1-0043: chip found @ 0x86 (ivtv i2c driver #0) > saa7115 1-0021: saa7115 found @ 0x42 (ivtv i2c driver #0) > msp3400 1-0040: MSP4418G-A2 found @ 0x80 (ivtv i2c driver #0) > msp3400 1-0040: MSP4418G-A2 supports nicam and radio, mode is autodetect and > autoselect > ts: Compaq touchscreen protocol output > ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes) > ivtv0: Encoder revision: 0x02060039 > ivtv0 warning: Encoder Firmware can be buggy, use version 0x02040011, > 0x02040024 or 0x02050032. > ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total) > ivtv0: Allocate DMA encoder YUV stream: 161 x 12960 buffers (2048KB total) > ivtv0: Allocate DMA encoder VBI stream: 80 x 26208 buffers (2048KB total) > ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB > total) > ivtv0: Create encoder radio stream > tuner 1-0061: type set to 38 (Philips PAL/SECAM multi (FM1216ME MK3)) > ivtv0: Initialized Hauppauge WinTV PVR-250, card #0 > ivtv: ==================== END INIT IVTV ==================== > > > I am wondering why he is initializing here a WinTV PVR-250 card. Another > thing in the first log is the line > ivtv0: Unknown model 30039, defaulting to PVR-150. Perhaps here is a problem? _______________________________________________ ivtv-users mailing list [email protected] http://ivtvdriver.org/mailman/listinfo/ivtv-users
