Unknown wrote:
Hi Mailinglist Users,
According to the Mailinglist rules: I am not subscribed to this List.
I downloaded and installed today the new 0.10.4 driver in the hope that
this driver now supports my TV-Card, also because i have seen this:
...
#ifdef HAVE_XC3028
/* Yuan PG600-2/GotView PCI DVD Lite/Club3D ZAP-TV1x01 cards */
...
in the ivtv-cards.c inside the ivtv-0.10.4.tar.gz:/ivtv-0.10.4/driver/
I dont have a clue about programming, i am just a normal user. So i
thought the driver would detect my card automatically. But it has not.
The dmesg output of the ivtv modules:
ivtv: ==================== START INIT IVTV ====================
ivtv: version 0.10.4 (tagged release) loading
ivtv: Linux version: 2.6.21-1.3228.fc7 SMP mod_unload
ivtv: In case of problems please include the debug info between
ivtv: the START INIT IVTV and END INIT IVTV lines, along with
ivtv: any module options, when mailing the ivtv-users mailinglist.
eth0: forcedeth.c: subsystem: 01462:7310 bound to 0000:00:0a.0
ivtv0: Autodetected Yuan PG600, Diamond PVR-550 card (cx23416 based)
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 19
ACPI: PCI Interrupt 0000:01:08.0[A] -> Link [LNKC] -> GSI 19 (level,
low) -> IRQ 19
i2c_adapter i2c-0: nForce2 SMBus adapter at 0x5000
i2c_adapter i2c-1: nForce2 SMBus adapter at 0x6000
ivtv0: loaded v4l-cx2341x-enc.fw firmware (376836 bytes)
ivtv0: Encoder revision: 0x02060039
cx25840 2-0044: cx25843-24 found @ 0x88 (ivtv i2c driver #0)
cx25840 2-0044: loaded v4l-cx25840.fw firmware (16382 bytes)
ivtv0: Registered device video0 for encoder MPEG (4 MB)
ivtv0: Registered device video32 for encoder YUV (2 MB)
ivtv0: Registered device vbi0 for encoder VBI (1 MB)
ivtv0: Registered device video24 for encoder PCM audio (1 MB)
ivtv0: Initialized Yuan PG600, Diamond PVR-550, card #0
ivtv: ==================== END INIT IVTV ====================
lspci -v:
01:08.0 Multimedia video controller: Internext Compression Inc iTVC16
(CX23416) MPEG-2 Encoder (rev 01)
Subsystem: Unknown device ffab:0600
Flags: bus master, medium devsel, latency 64, IRQ 19
Memory at cc000000 (32-bit, prefetchable) [size=64M]
Capabilities: [44] Power Management version 2
My Linux distribution is Fedora 7. The Kernel is
kernel-2.6.21-1.3228.fc7 arch:x86_64
Do i have to add some lines or options in my modprobe.conf?
Please help me.
What kind of help do you need? According to the above dmesg output,
it looks like your card is installed, configured and initialized. You should
have
devices /dev/video0, /dev/video32 /dev/vbi0 /dev/video24. To test
it, you should be able to do a 'cat /dev/video0 > /tmp/test.mpg',
and see the file grow. If in fact that works, then you just need
to figure out what kind of TV viewing application you are going to use
and let it know you have a /dev/video0 device. There is lots
of discussion about that all over the web. mythtv, tvtime, mplayer,
etc are all possibilities.
begin:vcard
fn:Mark Paulus
n:Paulus;Mark
org:MCI;Lec Interfaces / 40419
adr;dom:;;2424 Garden of the Gods Rd;Colorado Springs;CO;80919
email;internet:[EMAIL PROTECTED]
title:Mark Paulus
tel;work:719-535-5578
tel;pager:800-pagemci / 1406052
tel;home:v622-5578
version:2.1
end:vcard
_______________________________________________
ivtv-users mailing list
[email protected]
http://ivtvdriver.org/mailman/listinfo/ivtv-users
