Am Donnerstag, den 19.07.2007, 20:31 +0200 schrieb Sander Sweers: > Put the person in cc as this person is not subscribed to the list.. > > On do, 2007-07-19 at 20:29 +0200, Sander Sweers wrote: > > On do, 2007-07-19 at 09:22 -0600, Mark Paulus wrote: > > > > I downloaded and installed today the new 0.10.4 driver in the hope that > > > > this driver now supports my TV-Card, also because i have seen this: > > > > > > > > ... > > > > #ifdef HAVE_XC3028 > > > > > > > > /* Yuan PG600-2/GotView PCI DVD Lite/Club3D ZAP-TV1x01 cards */ > > > > ... > > > > > > > > in the ivtv-cards.c inside the ivtv-0.10.4.tar.gz:/ivtv-0.10.4/driver/ > > > > Although ivtv might recognize the card properly it does not mean the > > tuner on this card is supported in linux.
There is an entry in /usr/share/doc/kernel-doc-2.6.21/Documentation/video4linux/CARDLIST.tuner: tuner=71 - Xceive xc3028 I thought this means, the tuner is supported in linux. I am wrong with that? > > If I am not mistaken there is some very experimental support in someones > > forked branch of v4l-dvb but this will be difficult to get working > > properly for a user if at all. > > > > > > ivtv: ==================== START INIT IVTV ==================== > > > > ivtv: version 0.10.4 (tagged release) loading > > > > ivtv: Linux version: 2.6.21-1.3228.fc7 SMP mod_unload > > > > ivtv: In case of problems please include the debug info between > > > > ivtv: the START INIT IVTV and END INIT IVTV lines, along with > > > > ivtv: any module options, when mailing the ivtv-users mailinglist. > > > > eth0: forcedeth.c: subsystem: 01462:7310 bound to 0000:00:0a.0 > > > > ivtv0: Autodetected Yuan PG600, Diamond PVR-550 card (cx23416 based) > > > > ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 19 > > > > ACPI: PCI Interrupt 0000:01:08.0[A] -> Link [LNKC] -> GSI 19 (level, > > > > low) -> IRQ 19 > > > > i2c_adapter i2c-0: nForce2 SMBus adapter at 0x5000 > > > > i2c_adapter i2c-1: nForce2 SMBus adapter at 0x6000 > > > > ivtv0: loaded v4l-cx2341x-enc.fw firmware (376836 bytes) > > > > ivtv0: Encoder revision: 0x02060039 > > > > cx25840 2-0044: cx25843-24 found @ 0x88 (ivtv i2c driver #0) > > > > cx25840 2-0044: loaded v4l-cx25840.fw firmware (16382 bytes) > > > > ivtv0: Registered device video0 for encoder MPEG (4 MB) > > > > ivtv0: Registered device video32 for encoder YUV (2 MB) > > > > ivtv0: Registered device vbi0 for encoder VBI (1 MB) > > > > ivtv0: Registered device video24 for encoder PCM audio (1 MB) > > > > ivtv0: Initialized Yuan PG600, Diamond PVR-550, card #0 > > > > ivtv: ==================== END INIT IVTV ==================== > > > > > > What kind of help do you need? According to the above dmesg output, > > > it looks like your card is installed, configured and initialized. The card is detected as: Yuan PG600, Diamond PVR-550 and not as: Yuan PG600-2/GotView PCI DVD Lite/Club3D ZAP-TV1x01! > > > You should have > > > devices /dev/video0, /dev/video32 /dev/vbi0 /dev/video24. To test > > > it, you should be able to do a 'cat /dev/video0 > /tmp/test.mpg', > > > and see the file grow. If in fact that works, then you just need > > > to figure out what kind of TV viewing application you are going to use > > > and let it know you have a /dev/video0 device. There is lots > > > of discussion about that all over the web. mythtv, tvtime, mplayer, > > > etc are all possibilities. > > > > There is no tuner detected and if you capture it will most likely give a > > black image. Correct, i already tested this. > I am not sure but you *might* get the s-video in to work... > > But untill the tuner is supported your out of luck :( I can not test this suggestion, because i dont have a Television set. > > > > Greets > > Sander Greets back Knut _______________________________________________ ivtv-users mailing list [email protected] http://ivtvdriver.org/mailman/listinfo/ivtv-users
