On Monday 20 August 2007 09:52, [EMAIL PROTECTED] wrote: > I am hopefully in my final steps towards getting my PVR-350 working for a > Mythtv installation. I am using Mandriva 2007 64 bit with the > 2.6.17.-14mdv kernel. I appear to have a functional ivtv install and I am > able to capture some snow with cat /dev/video0 > test.mpg and play it with > mplayer. I just cant get live tv to show up in mythtv. Are there some > additional things I need to do in /etc/modprobe.conf? I have found some > of these posts, but I dont know if they apply to this version of the ivtv > driver. Do I need to modprobe ivtv-fb as well as ivtv? You can see dmesg > output below. > > Thx > SFS > > Users of the PVR-350 (may?) need to add a line to /etc/modprobe.conf if > they want to enable TV-Out, like this: > > # load ivtv-fb for PVR-350 output > install ivtv /sbin/modprobe --ignore-install ivtv; /sbin/modprobe ivtv-fb > > # /sbin/depmod -a > # /sbin/modprobe ivtv > > With the ivtv-fb line in your modprobe.conf, your system will > automatically load up the ivtv-fb module. If you have that line commented > out, you can load the ivtv-fb module up manually, with this command: > > # /sbin/modprobe ivtv-fb > > > ivtv: ==================== START INIT IVTV ==================== > > ivtv: version 0.7.0 (tagged release) loading > > ivtv: Linux version: 2.6.17-14mdv SMP mod_unload gcc-4.1 > > ivtv: In case of problems please include the debug info between > > ivtv: the START INIT IVTV and END INIT IVTV lines, along with > > ivtv: any module options, when mailing the ivtv-users mailinglist. > > ivtv0: Autodetected Hauppauge WinTV PVR-350 card (cx23415 based) > > ivtv0: Unreasonably low latency timer, setting to 64 (was 32) > > tveeprom 0-0050: Hauppauge model 48132, rev K268, serial# 9921474 > > tveeprom 0-0050: tuner model is LG TAPE H001F MK3 (idx 68, type 47) > > tveeprom 0-0050: TV standards NTSC(M) (eeprom 0x08) > > tveeprom 0-0050: audio processor is MSP4448 (idx 27) > > tveeprom 0-0050: decoder processor is SAA7115 (idx 19) > > tveeprom 0-0050: has radio, has IR remote > > tuner 0-0061: chip found @ 0xc2 (ivtv i2c driver #0) > > tda9887 0-0043: chip found @ 0x86 (ivtv i2c driver #0) > > saa7115 0-0021: saa7115 found @ 0x42 (ivtv i2c driver #0) > > saa7127 0-0044: saa7129 found @ 0x88 (ivtv i2c driver #0) > > msp3400 0-0040: MSP4448G-A2 found @ 0x80 (ivtv i2c driver #0) > > msp3400 0-0040: MSP4448G-A2 supports radio, mode is autodetect and > > autoselect > > ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes) > > ivtv0: loaded v4l-cx2341x-dec.fw firmware (262144 bytes) > > ivtv0: Encoder revision: 0x02060039 > > ivtv0 warning: Encoder Firmware can be buggy, use version 0x02040011, > > 0x02040024 or 0x02050032. > > ivtv0: Decoder revision: 0x02020023 > > ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB > > total) > > ivtv0: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB > > total) ivtv0: Allocate DMA encoder VBI stream: 120 x 17472 buffers > > (2048KB total) ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 > > buffers (2048KB total) > > ivtv0: Create encoder radio stream > > ivtv0: Allocate DMA decoder MPEG stream: 16 x 65536 buffers (1024KB > > total) ivtv0: Allocate DMA decoder VBI stream: 512 x 2048 buffers (1024KB > > total) ivtv0: Create decoder VOUT stream > > ivtv0: Allocate DMA decoder YUV stream: 24 x 43200 buffers (1024KB total) > > ivtv0: loaded v4l-cx2341x-init.mpg firmware (155648 bytes) > > ivtv0 warning: 100 ms time out waiting for firmware > > ivtv0 warning: Failed api call 0x00000002 with result 0xfffffff0 > > tuner 0-0061: type set to 47 (LG NTSC (TAPE series)) > > ivtv0 warning: 1000 ms time out waiting for firmware > > ivtv0 warning: Failed api call 0x00000010 with result 0xfffffff0 > > ivtv0: Initialized Hauppauge WinTV PVR-350, card #0 > > ivtv: ==================== END INIT IVTV ====================
Following the howto I cannot do this... Load the modules If you have an older version of ivtv loaded, you need to remove the modules before you can load the new modules. You also have to stop the application that's using the tuner cards before you can remove the modules. /sbin/rmmod ivtv cx25840 tuner tveeprom msp3400 wm8775 tda9887 saa7115 saa7127 Here is the output [EMAIL PROTECTED] mythtv]# /sbin/rmmod ivtv cx25840 tuner tveeprom msp3400 wm8775 tda9887 saa7115 saa7127 ERROR: Module ivtv is in use ERROR: Module cx25840 does not exist in /proc/modules ERROR: Module tveeprom is in use by bttv,ivtv ERROR: Module wm8775 does not exist in /proc/module I suspect my problem may be related to this? Any help would be greatly appreciated. Thx! Scott _______________________________________________ ivtv-users mailing list [email protected] http://ivtvdriver.org/mailman/listinfo/ivtv-users
