Tomorrow I will convert it to Eagle. And then for KiCAD... On Jul 9, 6:54 pm, Sebastien Lelong <[email protected]> wrote: > As for me, it would be better with Eagle... (I already heard this kind of > discussion before :)) > > 2010/7/9 funlw65 <[email protected]> > > > > > Warning, the project is in a raw form. I mean, I had no time to edit > > the component values (just copied components form another project > > which I converted to DipTrace). But having sources, anyone can do it. > > > On Jul 9, 6:14 pm, funlw65 <[email protected]> wrote: > > > I forgot to say that the main difference is the design himself. Just > > > compare them. > > > > On Jul 9, 6:08 pm, funlw65 <[email protected]> wrote: > > > > > Not exactly. Pinguino have RA4 pin connected to positive trace via > > > > LED. Also have a second push-button for "Start Application". It also > > > > have a 5V power regulator on board. The LED on Pinguino signal the > > > > moment when you are in "Run Application" mode. Because is inverse in > > > > this board, it will signal how long board is in boot mode. > > > > > Also, I excluded regulator because must be obligatory present on an > > > > application motherboard because you probably will have a cooling > > > > radiator specific to your application. In this case, you disconnect > > > > the jumper so your microcontroller will have his power from the > > > > motherboard and not from USB as is the case when you breadboard it for > > > > tests. Also, the LED on this board can be disconnected via a jumper. I > > > > can say here are a lot of differences. > > > > > On Jul 9, 5:58 pm, Sebastien Lelong <[email protected]> > > > > wrote: > > > > > > But is it like a Pinguino ? If so, why not directly using Pinguino ? > > Is it > > > > > because there's no ICSP ? > > > > > > 2010/7/9 vasi vasi <[email protected]> > > > > > > > These are project sources (usable with free version of DipTrace). > > > > > > So, can be improved/modified by anyone. > > > > > > -- > > > > > > Vasi > > > > > > > -- > > > > > > You received this message because you are subscribed to the Google > > Groups > > > > > > "jallib" group. > > > > > > To post to this group, send email to [email protected]. > > > > > > To unsubscribe from this group, send email to > > > > > > [email protected]<jallib%[email protected]> > > <jallib%[email protected]<jallib%[email protected]> > > > > > > > . > > > > > > > For more options, visit this group at > > > > > >http://groups.google.com/group/jallib?hl=en. > > > > > > -- > > > > > Sébastien Lelonghttp://www.sirloon.nethttp://sirbot.org > > > -- > > You received this message because you are subscribed to the Google Groups > > "jallib" group. > > To post to this group, send email to [email protected]. > > To unsubscribe from this group, send email to > > [email protected]<jallib%[email protected]> > > . > > For more options, visit this group at > >http://groups.google.com/group/jallib?hl=en. > > -- > Sébastien Lelonghttp://www.sirloon.nethttp://sirbot.org
-- You received this message because you are subscribed to the Google Groups "jallib" group. To post to this group, send email to [email protected]. To unsubscribe from this group, send email to [email protected]. For more options, visit this group at http://groups.google.com/group/jallib?hl=en.
