I borrowed a second Arduino from an acquaintance, downloaded programs, installed them and it works perfectly, but there's really no fun in that. Quickly returned the borrowed item. I'll just look for another PIC with fewer bells and whistles.
Op zaterdag 4 november 2023 om 10:50:22 UTC+1 schreef Hans van Veldhuizen: > Hi Rob, > It has to do with the pin A2. If i change it to C2 the both are working > > Op zaterdag 4 november 2023 om 07:56:20 UTC+1 schreef Rob CJ: > >> Hi Hans, >> >> The only difference that I see is the looptime. >> >> Instead of 1 second it is 1 ms but it depends on how fast the data is >> received. If that is too fast will that disturb the servo movement? >> >> Kind regards, >> >> Rob >> >> >> >> ------------------------------ >> *Van:* [email protected] <[email protected]> namens Hans van >> Veldhuizen <[email protected]> >> *Verzonden:* vrijdag 3 november 2023 22:13 >> *Aan:* jallib <[email protected]> >> *Onderwerp:* Re: [jallib] Camera_Gimbal >> >> Have changed with attached basic. Same result. Changed 325 for 324 same >> result >> >> Op vrijdag 3 november 2023 om 21:27:23 UTC+1 schreef Hans van Veldhuizen: >> >> Hi Rob, >> If I add this before the original forever loop then just servo 2 moves. >> Changed servo's same result >> forever loop >> >> servo_move(60,1) >> servo_move(60,2) >> delay_1S(2) >> >> servo_move(150,1) >> servo_move(150,2) >> delay_1S(2) >> >> end loop >> >> Op vrijdag 3 november 2023 om 19:11:13 UTC+1 schreef Rob CJ: >> >> Hi Hans, >> >> I cannot see any errors. So the data is received correctly but the >> servo's do not work? >> >> Have you tried to get the servo's working without the receive routines? >> So just hard-code some values to see if the servo's are working? >> >> Kind regards, >> >> Rob >> >> >> >> ------------------------------ >> *Van:* [email protected] <[email protected]> namens Hans van >> Veldhuizen <[email protected]> >> *Verzonden:* donderdag 2 november 2023 13:09 >> *Aan:* jallib <[email protected]> >> *Onderwerp:* [jallib] Camera_Gimbal >> >> Hello all, >> My question again. I'm trying to make a two-way camera Gimbal. I have >> modified working programs. The transmitter now has two ADC inputs and the >> receiver must control two servos. The signals arrive correctly at the >> receiver in fits and starts. I can't get the servos to work. Attached are >> the two files. >> Please respond again, >> regards >> Hans >> >> -- >> You received this message because you are subscribed to the Google Groups >> "jallib" group. >> To unsubscribe from this group and stop receiving emails from it, send an >> email to [email protected]. >> To view this discussion on the web visit >> https://groups.google.com/d/msgid/jallib/ff970ccd-ffb8-473f-991f-1441f768da3cn%40googlegroups.com >> >> <https://groups.google.com/d/msgid/jallib/ff970ccd-ffb8-473f-991f-1441f768da3cn%40googlegroups.com?utm_medium=email&utm_source=footer> >> . >> >> -- >> You received this message because you are subscribed to the Google Groups >> "jallib" group. >> To unsubscribe from this group and stop receiving emails from it, send an >> email to [email protected]. >> To view this discussion on the web visit >> https://groups.google.com/d/msgid/jallib/8093b573-4fb8-492a-ab0f-5db352424ffcn%40googlegroups.com >> >> <https://groups.google.com/d/msgid/jallib/8093b573-4fb8-492a-ab0f-5db352424ffcn%40googlegroups.com?utm_medium=email&utm_source=footer> >> . >> > -- You received this message because you are subscribed to the Google Groups "jallib" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. To view this discussion on the web visit https://groups.google.com/d/msgid/jallib/9e7aa511-70c4-4dc5-a14c-8c624f619a24n%40googlegroups.com.
