Milind Dumbare wrote: > Himanshu, I will need your "demsg' log too. Try giving hard coded port > numbers in command line instead of using defaults like > kgdboe= [EMAIL PROTECTED]/,[EMAIL PROTECTED]:6442/ > > Please check out the port syntax though. > -Miline > Hi Milind,
Below is my dmesg output. Please note that my rc.sysinit tries to reset the mac address and ip address again. Can it cause problems? BTW, How can I add support to the serial port (DTE) of my board? What is required to write the serial stub? Thanks Regards --Himanshu Linux version 2.6.20 ([EMAIL PROTECTED]) (gcc version 3.4.5) #5 PREEMPT Mon Mar 17 12:02:28 IST 2008 CPU: ARM920T [41129200] revision 0 (ARMv4T), cr=c0007177 Machine: Atmel AT91RM9200-EK Memory policy: ECC disabled, Data cache writeback On node 0 totalpages: 8192 DMA zone: 64 pages used for memmap DMA zone: 0 pages reserved DMA zone: 8128 pages, LIFO batch:0 Normal zone: 0 pages used for memmap Clocks: CPU 179 MHz, master 44 MHz, main 18.432 MHz CPU0: D VIVT write-back cache CPU0: I cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets CPU0: D cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets Built 1 zonelists. Total pages: 8128 Kernel command line: root=/dev/mmcblk0p1 rootdelay=3 mem=32M console=/dev/ttyS0,115200 [EMAIL PROTECTED]/,@192.168.0.169/ kgdboe: local port 6443 kgdboe: interface eth0 kgdboe: remote port 6442 kgdboe: remote IP 192.168.0.169 kgdboe: remote ethernet address ff:ff:ff:ff:ff:ff AT91: 128 gpio irqs in 4 banks PID hash table entries: 128 (order: 7, 512 bytes) Console: colour dummy device 80x30 Dentry cache hash table entries: 4096 (order: 2, 16384 bytes) Inode-cache hash table entries: 2048 (order: 1, 8192 bytes) Memory: 32MB = 32MB total Memory: 29956KB available (2172K code, 214K data, 96K init) Calibrating delay loop... 89.70 BogoMIPS (lpj=448512) Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok NET: Registered protocol family 16 usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 1024 (order: 0, 4096 bytes) TCP bind hash table entries: 512 (order: -1, 2048 bytes) TCP: Hash tables configured (established 1024 bind 512) TCP reno registered NetWinder Floating Point Emulator V0.97 (double precision) JFFS2 version 2.2. (NAND) (C) 2001-2006 Red Hat, Inc. io scheduler noop registered io scheduler anticipatory registered (default) Epson S1D13XXX FB Driver s1d13xxxfb: regs mapped at 0xc285c000, fb 1280 KiB mapped at 0xc2a00000 fb0: S1D13806 frame buffer device AT91 Watchdog Timer enabled (5 seconds, nowayout) atmel_usart.0: ttyS0 at MMIO map 0xfefff200 mem 0xfefff200 (irq = 1) is a ATMEL_SERIAL atmel_usart.1: ttyS1 at MMIO map 0xfffc4000 mem 0xc2860000 (irq = 7) is a ATMEL_SERIAL RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize eth0: Link now 100-FullDuplex eth0: AT91 ethernet at 0xfefbc000 int=24 100-FullDuplex (14:f0:9f:e5:14:f0) eth0: Davicom 9161 PHY (Copper) kgdboe: local port 6443 kgdboe: interface eth0 kgdboe: remote port 6442 kgdboe: remote IP 192.168.0.169 kgdboe: remote ethernet address ff:ff:ff:ff:ff:ff kgdboe: device eth0 not up yet, forcing it eth0: Link now 100-FullDuplex kgdboe: carrier detect appears untrustworthy, waiting 4 seconds kgdboe: no IP address for eth0, aborting kgdboe: netpoll_setup failed kgdboe failed physmap platform flash device: 00800000 at 10000000 physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank Amd/Fujitsu Extended Query Table at 0x0041 number of CFI chips: 1 cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness. RedBoot partition parsing not available at91_ohci at91_ohci: start at91_ohci at91_ohci: AT91 OHCI drivers/usb/core/inode.c: creating file 'devices' drivers/usb/core/inode.c: creating file '001' at91_ohci at91_ohci: new USB bus registered, assigned bus number 1 at91_ohci at91_ohci: supports USB remote wakeup at91_ohci at91_ohci: irq 23, io mem 0x00300000 at91_ohci at91_ohci: created debug files at91_ohci at91_ohci: resetting from state 'reset', control = 0x0 at91_ohci at91_ohci: OHCI controller state at91_ohci at91_ohci: OHCI 1.0, NO legacy support registers at91_ohci at91_ohci: control 0x083 HCFS=operational CBSR=3 at91_ohci at91_ohci: cmdstatus 0x00000 SOC=0 at91_ohci at91_ohci: intrstatus 0x00000004 SF at91_ohci at91_ohci: intrenable 0x8000001a MIE UE RD WDH at91_ohci at91_ohci: hcca frame #0005 at91_ohci at91_ohci: roothub.a 02000202 POTPGT=2 NPS NDP=2(2) at91_ohci at91_ohci: roothub.b 00000000 PPCM=0000 DR=0000 at91_ohci at91_ohci: roothub.status 00008000 DRWE at91_ohci at91_ohci: roothub.portstatus [0] 0x00000100 PPS at91_ohci at91_ohci: roothub.portstatus [1] 0x00000100 PPS usb usb1: default language 0x0409 usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1 usb usb1: Product: AT91 OHCI usb usb1: Manufacturer: Linux 2.6.20 ohci_hcd usb usb1: SerialNumber: at91 usb usb1: uevent usb usb1: usb_probe_device usb usb1: configuration #1 chosen from 1 choice usb usb1: adding 1-0:1.0 (config #1, interface 0) usb 1-0:1.0: uevent hub 1-0:1.0: usb_probe_interface hub 1-0:1.0: usb_probe_interface - got id hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected hub 1-0:1.0: standalone hub hub 1-0:1.0: no power switching (usb 1.0) hub 1-0:1.0: global over-current protection hub 1-0:1.0: power on to power good time: 4ms hub 1-0:1.0: local power source is good hub 1-0:1.0: no over-current condition exists hub 1-0:1.0: trying to enable port power on non-switchable hub hub 1-0:1.0: state 7 ports 2 chg 0000 evt 0000 drivers/usb/core/inode.c: creating file '001' udc: at91_udc version 3 May 2006 mice: PS/2 mouse device common for all mice at91_rtc at91_rtc: rtc core: registered at91_rtc as rtc0 AT91 Real Time Clock driver. AT91 MMC: 4 wire bus mode not supported by this driver - using 1 wire TCP cubic registered NET: Registered protocol family 1 NET: Registered protocol family 17 at91_rtc at91_rtc: setting the system clock to 1998-01-01 00:02:02 (883612922) Waiting 3sec before mounting root device... mmc0: card is read-write mmcblk0: mmc0:b368 SDM 975360KiB mmcblk0: p1 p2 p3 kjournald starting. Commit interval 5 seconds EXT3-fs warning: maximal mount count reached, running e2fsck is recommended EXT3 FS on mmcblk0p1, internal journal EXT3-fs: recovery complete. EXT3-fs: mounted filesystem with ordered data mode. VFS: Mounted root (ext3 filesystem). Freeing init memory: 96K AT91 SPI platform driver loaded AT91 SPI protocol driver loaded AT91 GPIO driver loaded kjournald starting. Commit interval 5 seconds EXT3-fs warning: maximal mount count reached, running e2fsck is recommended EXT3 FS on mmcblk0p2, internal journal EXT3-fs: recovery complete. EXT3-fs: mounted filesystem with ordered data mode. eth0: Setting MAC address to 00:04:9f:22:22:22 eth0: Link now 100-FullDuplex ------------------------------------------------------------------------- This SF.net email is sponsored by: Microsoft Defy all challenges. Microsoft(R) Visual Studio 2008. http://clk.atdmt.com/MRT/go/vse0120000070mrt/direct/01/ _______________________________________________ Kgdb-bugreport mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/kgdb-bugreport
