Tim What a muddle this google site is I was typing my message re DIAMOND and all of a sudden a little note came up in the right corner of the screen that another message had come in . My page disappeared!!!!!!!!!! Anyway the amount of non-syncro just depends on the turn of the crank handle i:e one turn 1/4 inch or in my case how much offset one wants I just measured the distance peak to peak and divided in half for my pattern. That box has just appeared again and if I click on it to see the latest message all i get is the screen saying the page is loading and that is all . As I said before What a muddle this site is. Richard
On Saturday, August 31, 2019 at 8:53:31 AM UTC+1, Tim wrote: > > The 2.5 I think should be divided by two since the spindle goes through a > push and a pull to complete a single wave. Am I thinking correctly on this? > > -------- Original message -------- > From: Richard Ellis <rchrd...@gmail.com <javascript:>> > Date: 8/30/19 4:05 AM (GMT-08:00) > To: Legacy Ornamental Mills <legacy-orna...@googlegroups.com <javascript:>> > > Subject: Re: TK Reciprocater long curves > > Hi Tim & Timothy > All interesting stuff. > When I did my latest as shown in the pic > I measured the distance of the wave peak to peak,, it was 2.5 inches. > After doing the first three runs. I returned the carriage back to the > start by ( crank handle ) Then I wound the carriage forward 6 turns of the > crank handle. ---Next I disconnected the leadscrew nut and pushed the > carriage back to the start position,,, re-connected the nut and did the > remaing three cuts. > All good practice and fun > Richard > > On Friday, August 30, 2019 at 11:47:26 AM UTC+1, Tim Ziegler wrote: >> >> Seeing all this Wave, now I'm going to have to figure out how to do that. >> And of course build the attachment. >> Kind Regards, >> >> Timothy J. Ziegler >> Ziegler WoodWork & Specialty >> 14171 160th Ave. >> Foreston MN 56330 >> >> 320-294-5798 shop >> 320-630-2243 cell >> >> >> On Fri, Aug 30, 2019 at 2:30 AM Tim <artma...@comcast.net> wrote: >> >>> >>> >>> >>> >>> Personally, I like it. You want to increase the amplitude, but by how >>> much? I’ll take a look at some possibilities that would give you 90° >>> travel of the spindle. It would only be able to be used on longer pitches. >>> >>> >>> >>> If Bill nows already how much offset is needed, he could save me some >>> time 😊 >>> >>> -- >>> You received this message because you are subscribed to the Google >>> Groups "Legacy Ornamental Mills" group. >>> To unsubscribe from this group and stop receiving emails from it, send >>> an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. >>> To view this discussion on the web visit >>> https://groups.google.com/d/msgid/legacy-ornamental-mills/5d68d0b0.1c69fb81.9cf02.a772SMTPIN_ADDED_MISSING%40gmr-mx.google.com >>> >>> <https://groups.google.com/d/msgid/legacy-ornamental-mills/5d68d0b0.1c69fb81.9cf02.a772SMTPIN_ADDED_MISSING%40gmr-mx.google.com?utm_medium=email&utm_source=footer> >>> . >>> >> -- > You received this message because you are subscribed to the Google Groups > "Legacy Ornamental Mills" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to legacy-ornamental-mills+unsubscr...@googlegroups.com > <javascript:>. > To view this discussion on the web visit > https://groups.google.com/d/msgid/legacy-ornamental-mills/7fa99ae6-bc53-4a8c-ba6a-ddbc806c2748%40googlegroups.com > > <https://groups.google.com/d/msgid/legacy-ornamental-mills/7fa99ae6-bc53-4a8c-ba6a-ddbc806c2748%40googlegroups.com?utm_medium=email&utm_source=footer> > . > -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/1d0f0d81-affc-49bb-a671-281c623a19f8%40googlegroups.com.
