Tim I think I have done all I want to at the present time I started on this WAVE caper to see if I could make DIAMOND shapes on the coat stand I was making WHY------------ it was our 60th wedding anniversary, Now I will have to think of what to do for the 70th one ??!! Richard
On Saturday, August 31, 2019 at 8:35:43 AM UTC+1, Tim wrote: > > I'm sitting in my lazyboy recliner right now and thinking about adding > more amplitude. It would be possible to increase the travel of the twist by > relocating the location of the connection on the index plate. So instead of > mounting the connecting arm on the 4" diameter, make a arm that extends the > location to say a 8" or 12" location. That way the spindle will twist more > for the amount of offset. It was something I did not include in the > original design nor did I try it out, but I've seen a couple of > Reciprocators that use this technique. > > Good luck and I hope you try this out Richard. > On Aug 30, 2019, at 4:18 AM, Tim Ziegler <timjz...@gmail.com <javascript:>> > wrote: >> >> Hey thanks for that and good to see someone up at the same time as me. >> lol >> I have a bunch of spindles to get done today on my lathe but if time >> permits this evening I'm going >> to start studying this more. Thanks for sharing. >> Kind Regards, >> >> Timothy J. Ziegler >> Ziegler WoodWork & Specialty >> 14171 160th Ave. >> Foreston MN 56330 >> >> 320-294-5798 shop >> 320-630-2243 cell >> >> >> On Fri, Aug 30, 2019 at 6:05 AM Richard Ellis < rchrd...@gmail.com >> <javascript:>> wrote: >> >>> Hi Tim & Timothy >>> All interesting stuff. >>> When I did my latest as shown in the pic >>> I measured the distance of the wave peak to peak,, it was 2.5 inches. >>> After doing the first three runs. I returned the carriage back to the >>> start by ( crank handle ) Then I wound the carriage forward 6 turns of the >>> crank handle. ---Next I disconnected the leadscrew nut and pushed the >>> carriage back to the start position,,, re-connected the nut and did the >>> remaing three cuts. >>> All good practice and fun >>> Richard >>> >>> On Friday, August 30, 2019 at 11:47:26 AM UTC+1, Tim Ziegler wrote: >>>> >>>> Seeing all this Wave, now I'm going to have to figure out how to do >>>> that. >>>> And of course build the attachment. >>>> Kind Regards, >>>> >>>> Timothy J. Ziegler >>>> Ziegler WoodWork & Specialty >>>> 14171 160th Ave. >>>> Foreston MN 56330 >>>> >>>> 320-294-5798 shop >>>> 320-630-2243 cell >>>> >>>> >>>> On Fri, Aug 30, 2019 at 2:30 AM Tim < artma...@comcast.net> wrote: >>>> >>>>> >>>>> >>>>> >>>>> >>>>> Personally, I like it. You want to increase the amplitude, but by how >>>>> much? I’ll take a look at some possibilities that would give you 90° >>>>> travel of the spindle. It would only be able to be used on longer >>>>> pitches. >>>>> >>>>> >>>>> >>>>> If Bill nows already how much offset is needed, he could save me some >>>>> time 😊 >>>>> >>>>> -- >>>>> You received this message because you are subscribed to the Google >>>>> Groups "Legacy Ornamental Mills" group. >>>>> To unsubscribe from this group and stop receiving emails from it, send >>>>> an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. >>>>> To view this discussion on the web visit >>>>> https://groups.google.com/d/msgid/legacy-ornamental-mills/5d68d0b0.1c69fb81.9cf02.a772SMTPIN_ADDED_MISSING%40gmr-mx.google.com >>>>> >>>>> <https://groups.google.com/d/msgid/legacy-ornamental-mills/5d68d0b0.1c69fb81.9cf02.a772SMTPIN_ADDED_MISSING%40gmr-mx.google.com?utm_medium=email&utm_source=footer>. >>>>> >>>>> >>>>> >>>> -- >>> You received this message because you are subscribed to the Google >>> Groups "Legacy Ornamental Mills" group. >>> To unsubscribe from this group and stop receiving emails from it, send >>> an email to legacy-ornamental-mills+unsubscr...@googlegroups.com >>> <javascript:>. >>> To view this discussion on the web visit >>> https://groups.google.com/d/msgid/legacy-ornamental-mills/7fa99ae6-bc53-4a8c-ba6a-ddbc806c2748%40googlegroups.com >>> >>> <https://groups.google.com/d/msgid/legacy-ornamental-mills/7fa99ae6-bc53-4a8c-ba6a-ddbc806c2748%40googlegroups.com?utm_medium=email&utm_source=footer>. >>> >>> >>> >> -- >> You received this message because you are subscribed to the Google Groups >> "Legacy Ornamental Mills" group. >> To unsubscribe from this group and stop receiving emails from it, send an >> email to legacy-ornamental-mills+unsubscr...@googlegroups.com >> <javascript:>. >> To view this discussion on the web visit >> https://groups.google.com/d/msgid/legacy-ornamental-mills/CAMBiJLGSTrc_PZLuaKvisnoWxCj6rqoaqETAJcFPFyUSX7qvvg%40mail.gmail.com >> >> <https://groups.google.com/d/msgid/legacy-ornamental-mills/CAMBiJLGSTrc_PZLuaKvisnoWxCj6rqoaqETAJcFPFyUSX7qvvg%40mail.gmail.com?utm_medium=email&utm_source=footer>. >> >> >> > -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/e043e486-5514-4c78-9bb6-d86c0320af01%40googlegroups.com.
