I got this to work using a IP VSwitch. All I changed was the name of the VSwitch. /proc/qeth shows as a Guest LAN... Anyone get a Ethernet VSwitch to work? I wonder what the difference is between Ethernet and IP VSwitches?
----- Original Message ----- From: "Bennie Hicks" <[EMAIL PROTECTED]> To: <[email protected]> Sent: Friday, July 28, 2006 4:14 PM Subject: Re: /proc/qeth for VSwitch
Rob, eth0 is vSwitch & hsi0 hipersocket GLAN [EMAIL PROTECTED] ~]$ ifconfig eth0 Link encap:Ethernet HWaddr 02:00:00:00:00:0C inet addr:nnn.n.nn.30 Bcast:nnn.n.nn.255 Mask:255.255.255.0 inet6 addr: fe80::200:0:100:c/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1492 Metric:1 RX packets:11589 errors:0 dropped:0 overruns:0 frame:0 TX packets:11986 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1792248 (1.7 MiB) TX bytes:2240932 (2.1 MiB) hsi0 Link encap:Ethernet HWaddr 00:00:00:00:00:00 inet addr:10.10.nn.30 Bcast:10.10.nn.127 Mask:255.255.255.128 inet6 addr: fe80::ff:fe00:0/64 Scope:Link UP BROADCAST RUNNING NOARP MULTICAST MTU:8192 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:3 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 b) TX bytes:264 (264.0 b) ==================================================================================================== [EMAIL PROTECTED] ~]$ cat /proc/qeth devices CHPID interface cardtype port chksum prio-q'ing rtr4 rtr6 fsz cnt -------------------------- ----- ---------- -------------- ---- ------ ---------- ---- ---- ----- ----- 0.0.0500/0.0.0501/0.0.0502 x29 eth0 GuestLAN QDIO 0 sw always_q_2 no no 64k 16 0.0.0600/0.0.0601/0.0.0602 x2A hsi0 GuestLAN Hiper 0 sw always_q_2 no no 16k 16 ==================================================================================================== q vswitch SWTCHTTZ detail VSWITCH SYSTEM SWTCHTTZ Type: VSWITCH Connected: 5 Maxconn: INFINITE PERSISTENT RESTRICTED NONROUTER Accounting: OFF VLAN Unaware State: Ready IPTimeout: 5 QueueStorage: 8 Portname: OSDTTZ2 RDEV: 3140 Controller: VSWITCH1 VDEV: 3140 Portname: OSDTTZ1 RDEV: 3170 Controller: VSWITCH2 VDEV: 3170 BACKUP VSWITCH Connection: RX Packets: 28316206 Discarded: 1936065 Errors: 0 TX Packets: 23133704 Discarded: 0 Errors: 0 RX Bytes: 1986154524 TX Bytes: 5025169565 Device: 3142 Unit: 002 Role: DATA Adapter Owner: LUITSRHN NIC: 0500 Name: UNASSIGNED RX Packets: 11645 Discarded: 0 Errors: 0 TX Packets: 12040 Discarded: 0 Errors: 0 RX Bytes: 1796048 TX Bytes: 1863418 Device: 0502 Unit: 002 Role: DATA Options: Broadcast Multicast IPv6 IPv4 VLAN Unicast IP Addresses: nnn.n.nn.30 MAC: 02-00-00-00-00-0C FE80::200:0:100:C MAC: 02-00-00-00-00-0C Local Multicast IP Addresses: 224.0.0.1 MAC: 01-00-5E-00-00-01 FF02::1 MAC: 33-33-00-00-00-01 Local FF02::1:FF00:C MAC: 33-33-FF-00-00-0C Local Rob Schwartz wrote:Hey everyone... I'm trying to connect to VSWITCH and can't seem to get it working. I have a VSWITCH defined as type ethernet, LAN unaware. My virtual server NIC uses vaddrs 3f04-3f06 and has been granted access to the VSWITCH. The VSWITCH looks like; q vswitch boswitch details VSWITCH SYSTEM BOSWITCH Type: VSWITCH Connected: 1 Maxconn: INFINITE PERSISTENT RESTRICTED ETHERNET Accounting: OFF VLAN Unaware State: Ready QueueStorage: 8 Portname: PORT0 RDEV: 0E86 Controller: TCPIP VDEV: 0E86 VSWITCH Connection: RX Packets: 0 Discarded: 0 Errors: 0 TX Packets: 0 Discarded: 0 Errors: 0 RX Bytes: 0 TX Bytes: 0 Device: 0E88 Unit: 002 Role: DATA Adapter Owner: LTROB NIC: 3F04 Name: UNASSIGNED RX Packets: 0 Discarded: 0 Errors: 0 TX Packets: 0 Discarded: 0 Errors: 0 RX Bytes: 0 TX Bytes: 0 Device: 3F06 Unit: 002 Role: DATA After starting the virtual server I get "qeth-bus-ccw-0.0.3f04 no interface found". When I look at /proc/qeth it shows the following; devices CHPID interface cardtype port chksum prio-q'ing rtr4 rtr6 fsz cnt -------------------------- ----- ---------- -------------- ---- ------ ---------- ---- ---- ----- ----- 0.0.3f00/0.0.3f01/0.0.3f02 x09 hsi0 GuestLAN Hiper 0 sw always_q_2 no no 16k 16 0.0.3f04/0.0.3f05/0.0.3f06 x0A GuestLAN QDIO 0 +++ LAN OFFLINE +++ Devices 3f00-02 are successfully connecting to a guest LAN. I can use this interface to ssh to the virtual server. I would like to define a second network interface. I *think* I have my VSWITCH defined properly but it looks like Linux sees these devices (3f04-06) as cardtype "Guest LAN". Could someone using VSWITCH's please cat /proc/qeth and send me the output. I'm wondering if the card type will be something like "VSwitch LAN". Thanks, Rob ---------------------------------------------------------------------- For LINUX-390 subscribe / signoff / archive access instructions, send email to [EMAIL PROTECTED] with the message: INFO LINUX-390 or visit http://www.marist.edu/htbin/wlvindex?LINUX-390---------------------------------------------------------------------- For LINUX-390 subscribe / signoff / archive access instructions, send email to [EMAIL PROTECTED] with the message: INFO LINUX-390 or visit http://www.marist.edu/htbin/wlvindex?LINUX-390
---------------------------------------------------------------------- For LINUX-390 subscribe / signoff / archive access instructions, send email to [EMAIL PROTECTED] with the message: INFO LINUX-390 or visit http://www.marist.edu/htbin/wlvindex?LINUX-390
