Linux-Hardware Digest #394, Volume #9 Tue, 9 Feb 99 09:14:10 EST
Contents:
Re: creative 3D blaster banshee (Shashank Misra)
Mylex RAID controllers ("Jon")
Re: Genius GM336-V Modem?? (Rob Clark)
Re: Two cordless mice at one receiver (Max Lock)
Intel SE 440BX-2 w/ onboard sound (RLopez6836)
Re: intel motherboards for linux (Shashank Misra)
Problem with ESS688 SoundChip (Christian Wagner)
Re: Linux and NEC VERSA 6030X? (Christian Wagner)
G200 Video Card install w/RH 5.1 (help) (Bob V)
Why is lpr refusing connections? ( Matt Magnasco)
Re: Can't ping my Gateway (but I can ping my own IP address) ("Gary Spivey")
Re: IBM PS/2 95 Server (Shaw Carruthers)
RD5.2 -SCSI bus timeout - aic 7880 ("Giuseppe Frangiamone")
Re: L2 cache kills linux : help! (nine@)
----------------------------------------------------------------------------
From: Shashank Misra <[EMAIL PROTECTED]>
Subject: Re: creative 3D blaster banshee
Date: Mon, 08 Feb 1999 18:05:11 -0600
Bonjour Etienne,
The Banshee-based cards aren't 'supported' under X right now. However,
with the newer (I think post 2.1.110) kernels, and the newest XFree86
(3.3.3 and later), you can use the card as a frame buffer device.
Details at
http://www.uno.edu/~adamico/banshee/
I have no idea how experienced you are with linux, but this would be
considered a non-trivial task by most. You can always fall back on the
generic vga server if things aren't working out.
bon chance,
shashank
------------------------------
From: "Jon" <[EMAIL PROTECTED]>
Crossposted-To: comp.os.linux.setup,linux.redhat.install,redhat.general
Subject: Mylex RAID controllers
Date: Mon, 8 Feb 1999 22:01:46 -0500
Anyone know if there are working [stable] drivers for either the Mylex
DAC960PJM or Mylex eXtremeRAID 1100?
Jon
------------------------------
Subject: Re: Genius GM336-V Modem??
From: [EMAIL PROTECTED] (Rob Clark)
Date: Tue, 09 Feb 1999 12:26:09 GMT
Oops, scratch that-- I meant Kye Systems with a "K" and the URL is
http://www.kye.co.uk/
Where's my caffeinated beverage?
In article <fHVv2.1293$[EMAIL PROTECTED]>,
Rob Clark <[EMAIL PROTECTED]> wrote:
>Your modem is sold by Wye Systems Ltd. (http://www.wye.co.uk/) and is
>probably manufactured by GVC in Taiwan. They only supply one set of
>drivers for all of their internal/external 23.8/33.6 modems, so if I were
>to take a _guess_, I'd say it's probably not a Winmodem.
>
>Good luck!
>Rob Clark, [EMAIL PROTECTED]
>http://www.o2.net/~gromitkc/winmodem.html
------------------------------
From: Max Lock <[EMAIL PROTECTED]>
Subject: Re: Two cordless mice at one receiver
Date: Tue, 09 Feb 1999 12:25:13 +0000
KL-Services wrote:
>
> Hi!
>
> Three years ago I purchased a Logitech Mouseman Cordless, which Ii´m
> still extremely fond of. Recently I got a wheelmouse into my hands and
> found it convienient for special applications (i.e. Netscape, ...). So I
>
> wonder, as there is also a cordless wheelmouse by Logitech, whether I
> could use both mice simultariously (my beloved Mouseman for "normal"
> applications; switching to wheelmouse for browser, ...). Furthermore I´m
>
> not sure whether the wheelmouse functions are supported by Linux.
>
> Any comments would be appreciated (please do not send Emails, as this is
>
> not my stationary adress)!
>
> Best regards,
>
> Axel
Hi Axel,
You can do this under gpm. if you use the -M option (upper case). This
enables you to use two mice. Works under X too if you make the mouse
device /dev/gpmdata
-Max.
--
Maxwell Lock, IRIX Specialist, CRAY Research / SGI UK.
"There are two major products that come out of Berkeley, LSD and UNIX.
We don't believe this to be a coincidence." -Jeremy S. Anderson
------------------------------
From: [EMAIL PROTECTED] (RLopez6836)
Subject: Intel SE 440BX-2 w/ onboard sound
Date: 9 Feb 1999 03:14:55 GMT
I have a Micron P2 350 with Intel Seattle 2 motherboard. It has a Yamaha DS-XG
PCI Audio Codec sound card onboard. I can't find an appropriate driver. Does
one exist, and if so where?
------------------------------
From: Shashank Misra <[EMAIL PROTECTED]>
Subject: Re: intel motherboards for linux
Date: Mon, 08 Feb 1999 19:47:36 -0600
all of them (alhtough things like on board sound sometimes geek out on you if
its some obscure audio chip)
------------------------------
From: Christian Wagner <[EMAIL PROTECTED]>
Subject: Problem with ESS688 SoundChip
Date: Tue, 09 Feb 1999 13:41:59 +0100
Hello,
I know, this is an old Notebook-Soundcard-Soundchip. (8bit Mono only) and it
should be easily configured.
It is working alleady, so most common problems are solved.
Anyway, there is still one thing, that is not working, why I need some help:
The Mixer of this card is not recognized.
TO be more specific:
All the IRQ, IO-Base, OPL3 settings etc. are set to the appropriate values. (BTW
the ESS688 is configured as 100% SB-compatible as adviced in the sound-HOWTO)
The soundcard is recognized and I can play whatever sound I'd like.
but if I cat /dev/sndstat one field is missing:
Mixers:
Well there should be something like
0: Sound Blaster
but there isn't.
I tried to fix this problem with several different ideas, like the Open Sound
System, Sound Compiled as Module, or sound embedded in Kernel.
All solutions lag the "support" of the mixer.
Thus I cannot use any mixer availible for Linux (X- or non-X app)
BTW:
The Mixer is working fine with Win95, even if it is hard for me to say this, ...
;-)
Help would be very fine.
But:
Please just mail me, if you really think that you know, what the problem is, and
if you've read this eMail carefully,
because I don not want to here something like: "It is an IRQ Problem"... <---
This cannot be. I'm sure.
Thanks,
Christian
--
We are the small voice that whispers to you in the lonely hours of
the night. We call to the darkness within all of you. We came from
the dark and to the dark we shall all return.
---ICQ#21196326---http://www.tu-harburg.de/~secw2604/---
------------------------------
From: Christian Wagner <[EMAIL PROTECTED]>
Subject: Re: Linux and NEC VERSA 6030X?
Date: Tue, 09 Feb 1999 13:52:48 +0100
Did you ever look on following page?
http://www.cs.utexas.edu/users/kharker/linux-laptop/
Maybe your answer is somewhere out there.
Greetings,
Christian
--
We are the small voice that whispers to you in the lonely hours of
the night. We call to the darkness within all of you. We came from
the dark and to the dark we shall all return.
---ICQ#21196326---http://www.tu-harburg.de/~secw2604/---
------------------------------
From: Bob V <[EMAIL PROTECTED]>
Subject: G200 Video Card install w/RH 5.1 (help)
Date: Mon, 08 Feb 1999 21:50:52 -0600
Hi Linux folks,
I am going to upgrade my existing PCI Diamond 3D 3000 card to the
Matrox G200 ( AGP ). I have been hearing that I need to get Xfree
3.3.3 installed
in order to support this card. Can someone briefly list the steps
involved as far
as what I need to do to get Xfree86 3.3.3, the steps on configuring the
new card
using xconfigurator, and whether I need to execute some type of
uninstall steps for
the card I am removing. I currently have Red Hat 5.1. Would this be more
straightforward if I just go out and buy Red Hat 5.2 and follow the
upgrade steps?
I am new to Linux and I don't want to break anything. I probably would
have a
hard time troubleshooting things if I got myself in trouble during this
process.
Thanks in advance,
Bob V
------------------------------
From: [EMAIL PROTECTED] ( Matt Magnasco
)
Crossposted-To: comp.os.linux.setup
Subject: Why is lpr refusing connections?
Date: 9 Feb 1999 03:21:31 GMT
Reply-To: [EMAIL PROTECTED]
I get the following error message when trying to print:
teriyaki.resnet.gatech.edu => lpr lart2
lpr: connect: Connection refused
jobs queued, but cannot start daemon.
It's a local printer, lpd and (AFAIK) all requisite kernel modules are
loaded. The kernel is 2.2.1.
What is lpr trying to connect to, and why (do you guess) is it being
refused?
--
==========Matt Magnasco==========http://teriyaki.resnet.gatech.edu/matt====
In the 60's, people took acid to make the | CE Grad Student (oy vey)
world weird. Now that the world is weird, | CE 4304 TA, Winter 1999
people take Prozac to make the world normal. | ¨Ya estamos all ?
------------------------------
From: "Gary Spivey" <[EMAIL PROTECTED]>
Crossposted-To: comp.os.linux.networking,comp.os.linux.questions,comp.os.linux.setup
Subject: Re: Can't ping my Gateway (but I can ping my own IP address)
Date: Tue, 09 Feb 1999 12:25:15 GMT
Fair enough, i will take whatever help I can get.
Attached is the ifconfig -a, netstat -nr, and I threw in a pnpdump for fun
...
Cheers,
Gary
Andrew Comech wrote in message <[EMAIL PROTECTED]>...
>> But I cannot ping my Gateway.
>So what's the output of ifconfig and netstat -nr ?
>
>It is naive: to glue pages of output and think they would not
>ask for more...
>
>Cheers,
>Andrew
>
=================================================
ifconfig -a
=================================================
lo Link encap:Local Loopback
inet addr:127.0.0.1 Bcast:127.255.255.255 Mask:255.0.0.0
UP BROADCAST LOOPBACK RUNNING MTU:3584 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0
TX packets:0 errors:0 dropped:0 overruns:0
eth0 Link encap:Ethernet HWaddr 00:A0:C9:CC:C6:21
inet addr:24.4.56.168 Bcast:24.4.56.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0
TX packets:0 errors:0 dropped:0 overruns:0
Interrupt:11 Base address:0x210
=================================================
netstat -nr
=================================================
Kernel IP routing table
Destination Gateway Genmask Flags MSS Window irtt
Iface
24.4.56.0 0.0.0.0 255.255.255.0 U 1500 0 0
eth0
127.0.0.0 0.0.0.0 255.0.0.0 U 3584 0 0 lo
0.0.0.0 24.4.56.1 0.0.0.0 UG 1500 0 0
eth0
=================================================
pnpdump
=================================================
# $Id: pnpdump.c,v 1.15a 1998/05/25 17:22:16 fox Exp $
# This is free software, see the sources for details.
# This software has NO WARRANTY, use at your OWN RISK
#
# For details of this file format, see isapnp.conf(5)
#
# For latest information on isapnp and pnpdump see:
# http://www.roestock.demon.co.uk/isapnptools/
#
# Compiler flags: -DREALTIME -DNEEDSETSCHEDULER
#
# Trying port address 0203
# Trying port address 020b
# Board 1 has serial identifier 9a 00 12 8f 55 44 00 8c 0e
# (DEBUG)
(READPORT 0x020b)
(ISOLATE PRESERVE)
(IDENTIFY *)
# Card 1: (serial identifier 9a 00 12 8f 55 44 00 8c 0e)
# Vendor Id CTL0044, Serial Number 1216341, checksum 0x9A.
# Version 1.0, Vendor version 1.0
# ANSI string -->Creative SB32 PnP<--
#
# Logical device id CTL0031
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed
if required
# Don't forget to uncomment the activate (ACT Y) when happy
(CONFIGURE CTL0044/1216341 (LD 0
# ANSI string -->Audio<--
# Multiple choice time, choose one only !
# Start dependent functions: priority preferred
# IRQ 5.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
# First DMA channel 1.
# 8 bit DMA only
# Logical device is not a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 1))
# Next DMA channel 5.
# 16 bit DMA only
# Logical device is not a bus master
# DMA may not execute in count by byte mode
# DMA may execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 1 (CHANNEL 5))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0220
# Maximum IO base address 0x0220
# IO base alignment 1 bytes
# Number of IO addresses required: 16
# (IO 0 (BASE 0x0220))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0330
# Maximum IO base address 0x0330
# IO base alignment 1 bytes
# Number of IO addresses required: 2
# (IO 1 (BASE 0x0330))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0388
# Maximum IO base address 0x0388
# IO base alignment 1 bytes
# Number of IO addresses required: 4
# (IO 2 (BASE 0x0388))
# Start dependent functions: priority acceptable
# IRQ 5, 7 or 10.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
# First DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is not a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 0))
# Next DMA channel 5, 6 or 7.
# 16 bit DMA only
# Logical device is not a bus master
# DMA may not execute in count by byte mode
# DMA may execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 1 (CHANNEL 5))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0220
# Maximum IO base address 0x0280
# IO base alignment 32 bytes
# Number of IO addresses required: 16
# (IO 0 (BASE 0x0220))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0300
# Maximum IO base address 0x0330
# IO base alignment 48 bytes
# Number of IO addresses required: 2
# (IO 1 (BASE 0x0300))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0388
# Maximum IO base address 0x0388
# IO base alignment 1 bytes
# Number of IO addresses required: 4
# (IO 2 (BASE 0x0388))
# Start dependent functions: priority acceptable
# IRQ 5, 7 or 10.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
# First DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is not a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 0))
# Next DMA channel 5, 6 or 7.
# 16 bit DMA only
# Logical device is not a bus master
# DMA may not execute in count by byte mode
# DMA may execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 1 (CHANNEL 5))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0220
# Maximum IO base address 0x0280
# IO base alignment 32 bytes
# Number of IO addresses required: 16
# (IO 0 (BASE 0x0220))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0300
# Maximum IO base address 0x0330
# IO base alignment 48 bytes
# Number of IO addresses required: 2
# (IO 1 (BASE 0x0300))
# Start dependent functions: priority functional
# IRQ 5, 7 or 10.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
# First DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is not a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 0))
# Next DMA channel 5, 6 or 7.
# 16 bit DMA only
# Logical device is not a bus master
# DMA may not execute in count by byte mode
# DMA may execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 1 (CHANNEL 5))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0220
# Maximum IO base address 0x0280
# IO base alignment 32 bytes
# Number of IO addresses required: 16
# (IO 0 (BASE 0x0220))
# Start dependent functions: priority functional
# IRQ 5, 7 or 10.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
# First DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is not a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 0))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0220
# Maximum IO base address 0x0280
# IO base alignment 32 bytes
# Number of IO addresses required: 16
# (IO 0 (BASE 0x0220))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0300
# Maximum IO base address 0x0330
# IO base alignment 48 bytes
# Number of IO addresses required: 2
# (IO 1 (BASE 0x0300))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0388
# Maximum IO base address 0x0388
# IO base alignment 1 bytes
# Number of IO addresses required: 4
# (IO 2 (BASE 0x0388))
# Start dependent functions: priority functional
# IRQ 5, 7 or 10.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
# First DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is not a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 0))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0220
# Maximum IO base address 0x0280
# IO base alignment 32 bytes
# Number of IO addresses required: 16
# (IO 0 (BASE 0x0220))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0300
# Maximum IO base address 0x0330
# IO base alignment 48 bytes
# Number of IO addresses required: 2
# (IO 1 (BASE 0x0300))
# Start dependent functions: priority functional
# IRQ 5, 7, 10 or 11.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
# First DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is not a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 0))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0220
# Maximum IO base address 0x0280
# IO base alignment 32 bytes
# Number of IO addresses required: 16
# (IO 0 (BASE 0x0220))
# End dependent functions
# (ACT Y)
))
#
# Logical device id CTL2011
# Device supports vendor reserved register @ 0x3b
# Device supports vendor reserved register @ 0x3c
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed
if required
# Don't forget to uncomment the activate (ACT Y) when happy
(CONFIGURE CTL0044/1216341 (LD 1
# Compatible device id PNP0600
# ANSI string -->IDE<--
# Multiple choice time, choose one only !
# Start dependent functions: priority preferred
# IRQ 10.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 10 (MODE +E)))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0168
# Maximum IO base address 0x0168
# IO base alignment 1 bytes
# Number of IO addresses required: 8
# (IO 0 (BASE 0x0168))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x036e
# Maximum IO base address 0x036e
# IO base alignment 1 bytes
# Number of IO addresses required: 2
# (IO 1 (BASE 0x036e))
# Start dependent functions: priority acceptable
# IRQ 11.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 11 (MODE +E)))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x01e8
# Maximum IO base address 0x01e8
# IO base alignment 1 bytes
# Number of IO addresses required: 8
# (IO 0 (BASE 0x01e8))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x03ee
# Maximum IO base address 0x03ee
# IO base alignment 1 bytes
# Number of IO addresses required: 2
# (IO 1 (BASE 0x03ee))
# Start dependent functions: priority acceptable
# IRQ 10, 11 or 15.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 10 (MODE +E)))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0100
# Maximum IO base address 0x01f8
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 0 (BASE 0x0100))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0300
# Maximum IO base address 0x03fe
# IO base alignment 2 bytes
# Number of IO addresses required: 2
# (IO 1 (BASE 0x0300))
# Start dependent functions: priority functional
# IRQ 15.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 15 (MODE +E)))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0170
# Maximum IO base address 0x0170
# IO base alignment 1 bytes
# Number of IO addresses required: 8
# (IO 0 (BASE 0x0170))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0376
# Maximum IO base address 0x0376
# IO base alignment 1 bytes
# Number of IO addresses required: 1
# (IO 1 (BASE 0x0376))
# End dependent functions
# (ACT Y)
))
#
# Logical device id CTL0021
# Device supports vendor reserved register @ 0x38
# Device supports vendor reserved register @ 0x3b
# Device supports vendor reserved register @ 0x3c
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed
if required
# Don't forget to uncomment the activate (ACT Y) when happy
(CONFIGURE CTL0044/1216341 (LD 2
# ANSI string -->WaveTable<--
# Multiple choice time, choose one only !
# Start dependent functions: priority preferred
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0620
# Maximum IO base address 0x0620
# IO base alignment 1 bytes
# Number of IO addresses required: 4
# (IO 0 (BASE 0x0620))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0620
# Maximum IO base address 0x0680
# IO base alignment 32 bytes
# Number of IO addresses required: 4
# (IO 0 (BASE 0x0620))
# End dependent functions
# (ACT Y)
))
#
# Logical device id CTL7001
# Device supports vendor reserved register @ 0x3b
# Device supports vendor reserved register @ 0x3c
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed
if required
# Don't forget to uncomment the activate (ACT Y) when happy
(CONFIGURE CTL0044/1216341 (LD 3
# Compatible device id PNPb02f
# ANSI string -->Game<--
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0200
# Maximum IO base address 0x0200
# IO base alignment 1 bytes
# Number of IO addresses required: 8
# (IO 0 (BASE 0x0200))
# (ACT Y)
))
#
# Logical device id CTL0051
# Device supports vendor reserved register @ 0x3b
# Device supports vendor reserved register @ 0x3c
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed
if required
# Don't forget to uncomment the activate (ACT Y) when happy
(CONFIGURE CTL0044/1216341 (LD 4
# ANSI string -->StereoEnhance<--
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0100
# Maximum IO base address 0x03f8
# IO base alignment 8 bytes
# Number of IO addresses required: 1
# (IO 0 (BASE 0x0100))
# (ACT Y)
))
# End tag... Checksum 0x00 (OK)
# Returns all cards to the "Wait for Key" state
(WAITFORKEY)
------------------------------
From: [EMAIL PROTECTED] (Shaw Carruthers)
Subject: Re: IBM PS/2 95 Server
Date: Tue, 09 Feb 1999 13:15:47 GMT
[EMAIL PROTECTED] (Greg Bodnar) wrote:
>I've come across an old IBM PS/2 9595 Server, and I'm looking for some
>information. The FAQ's list an address for PS/2 linux installations,
>but the site comes back with no DNS entry. I've been unable to find
>mirror sites, either.
>
The MCA Linux site has moved to:
http://www.dgmicro.com/mca/
------------------------------
From: "Giuseppe Frangiamone" <[EMAIL PROTECTED]>
Crossposted-To: alt.os.linux,linux.redhat.misc,tin.it.computer.pc.linux
Subject: RD5.2 -SCSI bus timeout - aic 7880
Date: Tue, 9 Feb 1999 13:21:02 +0100
I've installed Linux RH 5.2 on my Acer Altos 9000 Pro Server with aic-7880
SCSI controller with SCSI DAT, SCSI cdrom and 5 wide SCSI disk.
When I copy large data on the disks I get "bus timeout" errors.
I've used the same configuration with WINNT 4 without problems.
Can anyone help me?
Thanks
Giuseppe Frangiamone
------------------------------
From: [EMAIL PROTECTED] (nine@)
Subject: Re: L2 cache kills linux : help!
Date: Tue, 09 Feb 1999 09:56:11 +0200
In article <[EMAIL PROTECTED]>, [EMAIL PROTECTED] (M.
Buchenrieder) wrote:
>Please correct your >newsreader settings. You won't make
>any friends >with 256 >chars per line.
>You have a memory/CPU problem. Please check the sig11
>webpage at >http://www.bitwizard.nl/sig11 . > >Michael
256 chars per line!! aw no! - never heard of auto wrap?
Many thanks for that link. I had managed to get the L2
running by underclocking the bus a little. Also now though
getting signal 11 ers when compiling + installing. Theres
obviously a ram/chip/cache glitch here.
Thanks again.
-paul
------------------------------
** FOR YOUR REFERENCE **
The service address, to which questions about the list itself and requests
to be added to or deleted from it should be directed, is:
Internet: [EMAIL PROTECTED]
You can send mail to the entire list (and comp.os.linux.hardware) via:
Internet: [EMAIL PROTECTED]
Linux may be obtained via one of these FTP sites:
ftp.funet.fi pub/Linux
tsx-11.mit.edu pub/linux
sunsite.unc.edu pub/Linux
End of Linux-Hardware Digest
******************************
