Linux-Hardware Digest #991, Volume #12 Tue, 6 Jun 00 01:13:07 EDT
Contents:
Re: ZIP drive problems (7537637nc 983)
P3 halts on bootup (Checking 'hlt' instruction...) (Andrew Powell)
Re: Sv: looking for the right motherboard... (Edward Lee)
Re: Of RH 6.2 newbies and the USR 56K Fax PCI modem (Mark Witczak)
Re: Analog input via soundblaster (Paul Rubin)
Re: Zip 100 not mounting. (Chris Hessert)
Re: Parallel port zip drive (Chris Hessert)
Voodoo3 2000 problem... (Simon Lemieux)
Re: Disabling part of combo card in Pavilion (Edward Lee)
modprobe problem with syquest paraport devices. ("Mark Ricketts")
Re: Disabling part of combo card in Pavilion ("Unclaimed Mysteries")
Re: Troubles reading Real Time Clock (Edward Lee)
Fingerprint readingse. ("Alex Lam.")
How to configure modem? ("Mahmood Ahmed")
Re: P3 halts on bootup (Checking 'hlt' instruction...) ("Lonni J. Friedman")
CD Recorder Software (SageMage)
It's easy :) (Dmitry Tarnyagin)
Re: Troubles reading Real Time Clock ("Andrew N. McGuire ")
Re: need advice on future smallbiz network (Sarah)
Re: Removed cover due to heat. OK? (Matthew Gatto)
----------------------------------------------------------------------------
From: 7537637nc 983 <[EMAIL PROTECTED]>
Subject: Re: ZIP drive problems
Date: Mon, 05 Jun 2000 22:17:02 -0400
Hope this helps:
I had similar problems with my parallel port zip drive. I have two
parallel ports. My printer worked fine, but insmod ppa kept giving me
the same resource message you're getting.
After a lot of reading and research, I found that the lpd daemon (the
printer daemon) in 2.2.x kernels grabs all the parallel ports by default
at boot. So by the time you call "insmod ppa", there aren't any
resources available to it - they've all been assigned to lpd. Here's how
I got around it running Mandrake 6.1 - note that your file locations may
be different than mine:
1. make sure /etc/conf.modules contains a line like:
alias parport_lowlevel parport_pc
2. add a line to "/etc/lilo.conf":
append="lp=parport1" # Assigns my printer to parallel port 2 only
3. rerun /sbin/lilo.
4. after rebooting with the new lilo configuration, stick a zip disk in
the drive, and you should be able to run "modprobe ppa" which
(hopefully) will find an open port - parallel port 1 in my case. If this
works (the drive is spinning, little lights are flashing), then you
can....
5. create a directory to mount the zip drive - I use /mnt/zip.
6. execute:
mount -t msdos /dev/sda4 /mnt/zip
and your zip drive should now be accessible under /mnt/zip (/dev/sda4 is
your zip drive posing as a SCSI drive).
6. To get the drive mounted at boot, add the following to
/etc/rc.d/rc.local:
modprobe ppa
If you don't need printer support, make sure the lpd isn't starting
automatically. This alone may kill your problem, since it won't be
stealing the parallel ports. I use "linuxconf" to manage my boot
services, but I'm sure that's managed differently in Debian. Try turning
off lpd and then running "modprobe ppa" (again with a zip disk inserted
- just makes life easier).
Good Luck! ~Chris
------------------------------
Date: Mon, 05 Jun 2000 21:39:00 -0500
From: Andrew Powell <[EMAIL PROTECTED]>
Crossposted-To: comp.os.linux.misc
Subject: P3 halts on bootup (Checking 'hlt' instruction...)
This is a multi-part message in MIME format.
==============ADAB000D5699BDA10F70A45D
Content-Type: text/plain; charset=us-ascii
Content-Transfer-Encoding: 7bit
I have an HP Vectra VLi8 with a P3/500 running Linux 6.1 and operating
as a web server. This past weekend the system stopped running. On
bootup, the sequence stops at the message, "Checking 'hlt'
instruction...". This was not a problem before.
Typing "linux no-hlt" at the "LILO Boot:" prompt allows for proper
bootup, but placing append = "no-hlt" in /etc/lilo.conf does not produce
the same results.
Convincing HP technical support that there is a problem with the
system/processor appears to be a challenge, and I wanted to see of other
linux folk knew more about the problem.
aap
==============ADAB000D5699BDA10F70A45D
Content-Type: text/x-vcard; charset=us-ascii;
name="Andrew.Powell.vcf"
Content-Transfer-Encoding: 7bit
Content-Description: Card for Andrew Powell
Content-Disposition: attachment;
filename="Andrew.Powell.vcf"
begin:vcard
n:Powell;Andrew
tel;fax:773-728-8417
tel;work:773-728-8434
x-mozilla-html:FALSE
url:www.netcomp.net
org:NetComp, Inc.
adr:;;P.O. Box 25174;Chicago;IL;60625;us
version:2.1
email;internet:[EMAIL PROTECTED]
title:President
fn:Andrew Powell
end:vcard
==============ADAB000D5699BDA10F70A45D==
------------------------------
From: Edward Lee <[EMAIL PROTECTED]>
Subject: Re: Sv: looking for the right motherboard...
Date: Tue, 06 Jun 2000 14:48:14 -0700
www.amptron.com - product - System Board - PM-599LMR
Thomas Holby wrote:
> Can anyone give me a url to a place where bye and see this board!
>
> Thanks
> T.Holby
>
> Edward Lee <[EMAIL PROTECTED]> skrev i en
> nyhedsmeddelelse:[EMAIL PROTECTED]
> > I am using an Amtron 599LMR. micro-ATX (8"x7") with upto 8M AGP video
> (Sis530),
> > sound (cmi8738), 10T/100T lan (dvm9102) and modem (pct0211). The board
> works
> > with a Cyrix M II and K6-2. I have no problem with Linux so far. The
> only thing
> > I dislike is the two additional PCBs., one for ethernet module and one for
> modem
> > DAA. Since I am trying to fit this in a custom box of 4" high, the modem
> DAA
> > module is too tall. The ethernet module can be mounted sideway but the
> modem
> > module cannot. I probably fried my modem module while trying to rewire
> the
> > connectors. Other than that, this is not a bad board for US$85.
> >
> > By the way, this is great for mp3. The manual said that you can connect 4
> > channels sound, but I haven't tried it.
> >
> > James Scott Olsson wrote:
> >
> > > Hi, I'm looking for a motherboard with onboard sound, video and
> (preferably)
> > > networking. I'd like it to have as small a form factor as possible,
> > > including the thickness of the entire package- this means I wouldn't
> want to
> > > use a slot 1 style processor- and processor performance isn't too much
> of
> > > an issue really. Can anyone recommend a board that would fit these
> > > qualifications? I just want to be confident the linux support of the
> > > onboard hardware is as good as possible before I buy the board... :) I
> > > don't care about how fast the networking is or how good the video is,
> but
> > > sound should be as nice as possible...
> > >
> > > thanks in advance for the help!
> > >
> > > scott olsson
> > >
> > > ---
> > > "If I have seen farther than others, it is because I was standing on the
> > > shoulders of giants." - Isaac Newton
> > >
> > > "If I have not seen as far as others, it is because giants were standing
> on my
> > > shoulders." - Hal Abelson
> > >
> > > "If I have seen farther than others, it is because I have been
> surrounded by
> > > midgets." - Murray Gell-Mann
> >
------------------------------
From: Mark Witczak <[EMAIL PROTECTED]>
Crossposted-To: alt.os.linux,alt.os.linux.redhat,alt.os.linux.mandrake
Subject: Re: Of RH 6.2 newbies and the USR 56K Fax PCI modem
Date: Mon, 05 Jun 2000 23:02:28 -0400
Step 1: Download the LucentPCI-1_1-1_i386.rpm (for Red Hat)
Step 2: Install the package
Step 3: Reboot
Step 4: Go back into Gnome-RPP and go through the modem configuration. It
should detect the modem automagically. (For some reason mine came in at
ttyS14)
Good Luck
Mark
e miller wrote:
> Hi
>
> I have a U.S. Robotics 56K Fax PCI Modem. In Win98 Sucks Edition, it is
> at COM5, IRQ 10 and E400. How do i get Red Hat Linux 6.2 to recognize
> it?
> How do i use the setserial command? Where is KPPP in RH 6.2?
>
> Do i have to pull out my SB Live! Value card?
>
> Please set-by-step intructions only. I am a verrrrrrrrrrrry greeeen
> newbie.
>
> Thanks
------------------------------
From: [EMAIL PROTECTED] (Paul Rubin)
Subject: Re: Analog input via soundblaster
Date: 6 Jun 2000 03:02:53 GMT
In article <8hhbkf$sm1$[EMAIL PROTECTED]>,
Van Snyder <[EMAIL PROTECTED]> wrote:
>Is it possible/reasonable to use a soundblaster for low-speed analog
>input, i.e. for instrument sampling? I'm looking at signals in the
>100-200 Hz range, max.
>
>I thought of maybe just putting my inputs into the microphone/line input.
>
>What sort of software should I use to capture the signal in a file? And
>what is the file format?
The soundblaster just reads PCM samples; resolution and sample rate
are programmable. See http://www.lila.com/nautilus/ for an example
of how this can be done (including under Linux).
Note that the mic/line input is usually AC coupled to the A/D converters,
which means you won't be able to detect anything below audio frequency.
------------------------------
From: Chris Hessert <[EMAIL PROTECTED]>
Subject: Re: Zip 100 not mounting.
Date: Mon, 05 Jun 2000 23:14:01 -0400
Hope this helps:
I had similar problems with my parallel port zip drive. I have two
parallel ports. My printer on #2 worked fine, but "insmod ppa" kept
giving me fits - same errors you're getting.
After a lot of reading and research, I found that the lpd daemon (the
printer daemon) in 2.2.x kernels grabs all the parallel ports by default
at boot. So by the time you call "insmod ppa", there aren't any
resources available to it - they've all been assigned to lpd. Here's how
I got around it running Mandrake 6.1 - note that your file locations may
be different than mine.
1. make sure /etc/conf.modules contains a line like:
alias parport_lowlevel parport_pc
2. add a line to /etc/lilo.conf (assigns my printer to parallel port 2
only):
append="lp=parport1"
3. rerun /sbin/lilo
4. after rebooting with the new lilo configuration, stick a zip disk in
the drive (trust me, it just makes life easier), and you should be able
to run "modprobe ppa" which (hopefully) will now find an open port -
parallel port 1 in my case. If this works (the drive is spinning, little
lights are flashing), then you can...
5. create a directory to mount the zip drive (if you don't already have
one). I use /mnt/zip
6. execute:
mount -t [filesystem] /dev/sda4 /mnt/zip
[filesystem] could be msdos (dos), vfat (win95+), or ext2 (linux) -
however your zip disk is formatted. Your zip drive should now be
accessible under /mnt/zip (/dev/sda4 is your zip drive posing as a SCSI
drive).
7. To get the drive mounted at boot, add the following to
/etc/rc.d/rc.local:
modprobe ppa
If you don't need printer support, make sure lpd isn't starting
automatically at boot. This alone may fix your problem, since it won't
be stealing the parallel ports. I use "linuxconf" to manage my boot
services, but other distributions are managed differently. Try turning
off lpd and then running "modprobe ppa" (again with a zip disk
inserted).
If you only have one parallel port and need both a printer and the zip
drive, compile your kernel with both as modules. You should be able to
load one or the other at a time, although I don't have experience with
this. I'd be glad to hear from anyone who got both devices working on
one port with the pass-through feature!
Good Luck! ~Chris
------------------------------
From: Chris Hessert <[EMAIL PROTECTED]>
Subject: Re: Parallel port zip drive
Date: Mon, 05 Jun 2000 23:15:13 -0400
Hope this helps:
I had similar problems with my parallel port zip drive. I have two
parallel ports. My printer on #2 worked fine, but "insmod ppa" kept
giving me fits.
After a lot of reading and research, I found that the lpd daemon (the
printer daemon) in 2.2.x kernels grabs all the parallel ports by default
at boot. So by the time you call "insmod ppa", there aren't any
resources available to it - they've all been assigned to lpd. Here's how
I got around it running Mandrake 6.1 - note that your file locations may
be different than mine.
1. make sure /etc/conf.modules contains a line like:
alias parport_lowlevel parport_pc
2. add a line to /etc/lilo.conf (assigns my printer to parallel port 2
only):
append="lp=parport1"
3. rerun /sbin/lilo
4. after rebooting with the new lilo configuration, stick a zip disk in
the drive (trust me, it just makes life easier), and you should be able
to run "modprobe ppa" which (hopefully) will now find an open port -
parallel port 1 in my case. If this works (the drive is spinning, little
lights are flashing), then you can...
5. create a directory to mount the zip drive (if you don't already have
one). I use /mnt/zip
6. execute:
mount -t [filesystem] /dev/sda4 /mnt/zip
[filesystem] could be msdos (dos), vfat (win95+), or ext2 (linux) -
however your zip disk is formatted. Your zip drive should now be
accessible under /mnt/zip (/dev/sda4 is your zip drive posing as a SCSI
drive).
7. To get the drive mounted at boot, add the following to
/etc/rc.d/rc.local:
modprobe ppa
If you don't need printer support, make sure lpd isn't starting
automatically at boot. This alone may fix your problem, since it won't
be stealing the parallel ports. I use "linuxconf" to manage my boot
services, but other distributions are managed differently. Try turning
off lpd and then running "modprobe ppa" (again with a zip disk
inserted).
If you only have one parallel port and need both a printer and the zip
drive, compile your kernel with both as modules. You should be able to
load one or the other at a time, although I don't have experience with
this. I'd be glad to hear from anyone who got both devices working on
one port with the pass-through feature!
Good Luck! ~Chris
------------------------------
From: Simon Lemieux <[EMAIL PROTECTED]>
Reply-To: [EMAIL PROTECTED]
Subject: Voodoo3 2000 problem...
Date: Tue, 06 Jun 2000 03:16:50 GMT
Hi,
I bought a Voodoo3 2000 16Mg AGP... I used it for a few weeks, didn't have
time to install the glide drivers and everything. But then, when I woke up one
day, the graphics were messed up. Nothing had changed, I didn't play with any
config files, I just continued to program my stuff like I always do, but the
Video card was very messed up; when I rebooted, before the BIOS came in, there
is normally a Voodoo message saying something like "Voodoo3 2000, Interactive
Inc." etc... And it was written "V o o 3 2 0 n e a t v c " instead... the
text in the console was kind of interlaced, unreadable! And when X loaded the
graphics where like horizontally interlaced but very oddly...
I got the card out of my case and put back my Xpert 98 which works, I actually
don't need my Voodoo3, but since I payed for it, I was wondering if that could
be a burnout of some sort? What should I do?
Thanks,
Simon
------------------------------
From: Edward Lee <[EMAIL PROTECTED]>
Crossposted-To: comp.sys.hp.hardware
Subject: Re: Disabling part of combo card in Pavilion
Date: Tue, 06 Jun 2000 15:26:58 -0700
Very likely, I am not familiar with the Rockwell, but my PCtel 211 modem chip
is married to my CMI8738 sound chip. Both chips need decoders, A/D, D/A and
etc. It makes sense to put common logics in higher volume chips. The question
is what chips are used in more systems, sound or modem?
Unclaimed Mysteries wrote:
>
> I cannot do this. Disabling the Rockwell Riptide sound part in Device
> Manager renders the modem useless. Are they THAT tied together? Am I
> overlooking something?
------------------------------
From: "Mark Ricketts" <[EMAIL PROTECTED]>
Subject: modprobe problem with syquest paraport devices.
Date: Mon, 5 Jun 2000 23:28:13 -0400
I'm using Suse 6.4 on a 120Mhz Pentium, 128M dram, External Supra Express
56k modem on ttys1, etc. I also own two syquest drives;
SparQ 1.0Gb
/dev/pda1 /sparq vfat noauto, suid,exec,user 0 0
at address 0x3BC
EZ-Drive 135M
/dev/pda2 /ez vfat noauto, suid,exec,user 0 0
address=0x378
irq=7
dma=3
Using the command sequence "modprobe -v epat", "modprobe -v pd", I am only
able to get one drive to respond at any time. I cannot later mount more
than one drive. Are there any command line parameters that I should know
about in order to get both drives recognized? Are there some additional
settings for the "pd" drive type command that will allow me to specifically
identify each drive?
Mark
[EMAIL PROTECTED]
------------------------------
From: "Unclaimed Mysteries" <[EMAIL PROTECTED]>
Crossposted-To: comp.sys.hp.hardware
Subject: Re: Disabling part of combo card in Pavilion
Date: Mon, 5 Jun 2000 22:51:22 -0500
Edward Lee <[EMAIL PROTECTED]> wrote in message
news:[EMAIL PROTECTED]...
> Both chips need decoders, A/D, D/A and
> etc.
You are of course correct and I will soon be evicting this combo card from
the sleek HP case. With extreme prejudice.
Next issue for the group: What should the fate of this thing be? Creativity
and cruelty count.
--
It came from C. L. Smith's Unclaimed Mysteries.
http://www.unclaimedmysteries.net/
I'll probably, hang on to it, just in case...but I can dream.
------------------------------
From: Edward Lee <[EMAIL PROTECTED]>
Crossposted-To: comp.os.linux.misc
Subject: Re: Troubles reading Real Time Clock
Date: Tue, 06 Jun 2000 16:18:55 -0700
What is the standard notation for time server, similar to ns (name server). ts
did not work for me. Are there public time servers available, if my isp does not
have it?
Akira Yamanita wrote:
> David Efflandt wrote:
> >
> > On Mon, 5 Jun 2000 10:35:11 +0200, Cristiano Marini <[EMAIL PROTECTED]> wrote:
> > >My Linux 6.0 read incorrectly the real time clock when during startup calls
> > >hwclock
> >
> > The CMOS clock calendar has nothing to do with the real time clock. The
> > real time clock (rtc) is a precise timer.
> >
> > >In my system is arc=false and uts=false and I tried both hwclock &
> > >hwclock --directisa
> >
> > --directisa is only for Alpha cpu and not for Intel like yours.
> >
> > Instead you want to set your system 'date' properly and then run
> > 'hwclock --systohc' (or 'setclock' in RedHat).
> >
> > The easiest way to set your system time accurately before doing that is
> > with 'ntpdate -b timeserver' from the 'xntp' package.
>
> I use rdate.
>
> rdate -s timeserver
------------------------------
From: "Alex Lam." <"here,there"@everywhere.com>
Subject: Fingerprint readingse.
Date: Mon, 05 Jun 2000 21:33:36 -0700
I just saw a fingerprint reading mouse on the web. Can be the
ultimate security tool without have to worry about somebody can
crack your password and login to your machine.
Any chance that Linux/BSD will support this in the near future?
Thanks.
Alex Lam.
------------------------------
From: "Mahmood Ahmed" <[EMAIL PROTECTED]>
Crossposted-To: alt.os.linux.dial-up
Subject: How to configure modem?
Date: Tue, 6 Jun 2000 12:18:06 +0800
Hi
I am using U.S. Robotics 56K Voice Win modem (internal). Is there any way to
configure it in Linux (RedHat 6.1)?
Thanks for any help.
Mahmood
------------------------------
From: "Lonni J. Friedman" <[EMAIL PROTECTED]>
Crossposted-To: comp.os.linux.misc
Subject: Re: P3 halts on bootup (Checking 'hlt' instruction...)
Date: Tue, 06 Jun 2000 00:08:03 -0400
This must be a problem to your specific hardware, as such a bug in a P3
would be widely known by now. That plus the fact that I know of someone
who has a P3/500 that is not having any such problems running linux
right now.
Andrew Powell wrote:
>
> I have an HP Vectra VLi8 with a P3/500 running Linux 6.1 and operating
> as a web server. This past weekend the system stopped running. On
> bootup, the sequence stops at the message, "Checking 'hlt'
> instruction...". This was not a problem before.
>
> Typing "linux no-hlt" at the "LILO Boot:" prompt allows for proper
> bootup, but placing append = "no-hlt" in /etc/lilo.conf does not produce
> the same results.
>
> Convincing HP technical support that there is a problem with the
> system/processor appears to be a challenge, and I wanted to see of other
> linux folk knew more about the problem.
------------------------------
From: SageMage <[EMAIL PROTECTED]>
Subject: CD Recorder Software
Date: Mon, 05 Jun 2000 23:51:14 -0500
Is there Any software for Linux that records mp3s to CD (converts to wav
or track on the fly), kinda like nero for Winblowz???
------------------------------
From: Dmitry Tarnyagin <[EMAIL PROTECTED]>
Subject: It's easy :)
Date: Tue, 06 Jun 2000 07:43:07 +0400
There are no "standard" modems with additional IO ports yet.
I have WinModem too in my Tochiba notebook (MARS chip). There is a (some
buggy) Win (Lin) modem driver from Lucent - http://www.linmodems.org/ .
That's interesting, my current linmodem work better as old "standard"
USRobotics Sportster. Also I hasn't find any serious CPU usage by driver
- all work fine and light, thanx to Lucent.
With best regards,
Dmitry
# cat /proc/pci
...........
Bus 0, device 9, function 0:
Communication controller:
Lucent (ex-AT&T) Microelectronics Unknown device (rev 1).
Vendor id=11c1. Device id=441.
Medium devsel. Fast back-to-back capable.
IRQ 3. Master Capable. No bursts.Min Gnt=252.Max Lat=14.
Non-prefetchable 32 bit memory at 0xf4101000 [0xf4101000].
I/O at 0x14d0 [0x14d1].
I/O at 0x1000 [0x1001].
............
------------------------------
Crossposted-To: comp.os.linux.misc
From: "Andrew N. McGuire " <[EMAIL PROTECTED]>
Subject: Re: Troubles reading Real Time Clock
Date: Mon, 5 Jun 2000 23:57:28 -0500
On Tue, 6 Jun 2000, Edward Lee wrote:
+ What is the standard notation for time server, similar to ns (name server). ts
+ did not work for me. Are there public time servers available, if my isp does not
+ have it?
[ snip of jeopardy quoted text ]
Not to be mean, but a little research on your part would not hurt.
Go to www.google.com and search on 'time servers', the first hit
you get is 'Public NTP Time Servers' which is more than likely what
you want, the address of a time server you can use right?
Best Wishes,
anm
--
/*-------------------------------------------------------.
| Andrew N. McGuire |
| [EMAIL PROTECTED] |
`-------------------------------------------------------*/
------------------------------
From: Sarah <[EMAIL PROTECTED]>
Subject: Re: need advice on future smallbiz network
Date: Tue, 06 Jun 2000 00:57:19 -0400
If there are Unix networks, there can be Linux networks,
right?
[EMAIL PROTECTED] wrote:
>
> > I'm thinking of running a 3-way network, with a win95/98 box
> > for home use, a MAC G3 for the database/webserver, and Linux
> > for the network protocol.
>
> I'm not following you. Linux is an operating system, not a network
> protocol.
>
> Sent via Deja.com http://www.deja.com/
> Before you buy.
------------------------------
From: [EMAIL PROTECTED] (Matthew Gatto)
Subject: Re: Removed cover due to heat. OK?
Date: Tue, 06 Jun 2000 05:08:27 GMT
My computer goes nuts and starts beeping (BIOS?!) at me like a
fire-alarm after more than about an hour of playing quake3. This
didn't start happening until it started heating up outside as the
Spring progressed. The processor is over-clocked 50MHz though.
>
>Well, forgive me all over the place, but that's ****shit. It's an
>all-too-well-known fact that in hot summers, computer failure rises
>very steeply indeed. In hot summers, you DO have to take special
>precautions. Why do you think they try and keep the temperature well
>below 20 degrees Celsius in server-rooms, that has a reason you know...
>
>And if your computer is directly IN hot sunlight, well... there is no
>amount of cooling gonna be able to save that baby...
>
>If there were errors made while either designing the case (what do you
>expect with cheap Taiwanese cases anyway?) and/or cooling of hard disks
>& CPU's, things are even worse. If you have one of those 7200 or
>10.000 RPM disks, you had better have cooling fans blowing *directly*
>on them, or else... same goes for omitting the heat-conductive
>compound between the heat-sinks and the CPUs.
>Well, you get the picture.
>
>Maarten
>
>--
>
>Proofread carefully to see if you any words out.
--
~MGatto~
"Tech support?!!??! We don't need no stekin tech support!?!"
Support the anti-spam movement; see <http://www.cauce.org/>
------------------------------
** FOR YOUR REFERENCE **
The service address, to which questions about the list itself and requests
to be added to or deleted from it should be directed, is:
Internet: [EMAIL PROTECTED]
You can send mail to the entire list (and comp.os.linux.hardware) via:
Internet: [EMAIL PROTECTED]
Linux may be obtained via one of these FTP sites:
ftp.funet.fi pub/Linux
tsx-11.mit.edu pub/linux
sunsite.unc.edu pub/Linux
End of Linux-Hardware Digest
******************************
