Hello, [EMAIL PROTECTED] wrote: > With one, two and three drives on the pm I got no errors, so I tried to > change the power supply. I got two power supplies for the 16 harddrives > and the second one (with all Maxtor drives and the first pm) was failing. > After changing the power supply all problems where gone. Sorry for the > confusion.
It's amazing that, in SATA, PSU-problem-verified / PSU-problem-suggested ratio is significant. I don't think this ever was the case with PATA. SATA link seems much more susceptible to power quality and allows hooking up whole lot of drives. > The only remaining issue is that some sata links are only working with 1.5 > gbps and I can't figure out why. (ata3,4,5,6.x are the Maxtor drives and > ata7,8,9,10.x are the Samsung ones) > > jasmin ~ # dmesg | grep Gbps > ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 0) > ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 0) > ata5: SATA link up 3.0 Gbps (SStatus 123 SControl 0) > ata6: SATA link up 3.0 Gbps (SStatus 123 SControl 0) > ata6.00: SATA link up 1.5 Gbps (SStatus 113 SControl 300) > ata6.01: SATA link up 3.0 Gbps (SStatus 123 SControl 300) > ata6.02: SATA link up 3.0 Gbps (SStatus 123 SControl 300) > ata6.03: SATA link up 3.0 Gbps (SStatus 123 SControl 300) > ata6.04: SATA link up 3.0 Gbps (SStatus 123 SControl 300) > ata6.05: SATA link up 1.5 Gbps (SStatus 113 SControl 300) > ata7: SATA link up 3.0 Gbps (SStatus 123 SControl 0) > ata8: SATA link up 3.0 Gbps (SStatus 123 SControl 0) > ata9: SATA link up 3.0 Gbps (SStatus 123 SControl 0) > ata10: SATA link up 3.0 Gbps (SStatus 123 SControl 0) > ata10.00: SATA link up 3.0 Gbps (SStatus 123 SControl 300) > ata10.01: SATA link up 3.0 Gbps (SStatus 123 SControl 300) > ata10.02: SATA link up 3.0 Gbps (SStatus 123 SControl 300) > ata10.03: SATA link up 3.0 Gbps (SStatus 123 SControl 300) > ata10.04: SATA link up 3.0 Gbps (SStatus 123 SControl 300) > ata10.05: SATA link up 1.5 Gbps (SStatus 113 SControl 300) Hmm... That's how the hardware negotiated transfer rate w/ each other. SControl is telling the hardware that there's no speed limit and to go as high as it can but somehow 3.0Gbps negotiation failed and the link speed is limited to 1.5Gbps for some of the ports. Is the result always the same? What happens if you swap drives between ports? Also, if you have an extra PSU lying around, can you hook it up with some of the drives such that the load is more distributed. Oh.. Another note on PSU. I don't know whether this still holds for more recent ones but mid-to-high range multi-lane PSUs sometimes have lesser juice on 12v rail available for disks than low cost single lane PSUs. This is because high power 12v lanes are allocated to power video cards and disks can only pull power from (usually) single weak 12v lane. Thanks. -- tejun - To unsubscribe from this list: send the line "unsubscribe linux-ide" in the body of a message to [EMAIL PROTECTED] More majordomo info at http://vger.kernel.org/majordomo-info.html
