Hello, I would like to find out if this is an USB-Problem in the kernel or if this is a problem with the ALSA snd-usb-audio driver. So I recompiled the kernel without the snd-usb-audio module. When plugging the device into an usb port an unplugging it again I can still use my keyboard. Here's what dmesg says:
ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001803 POWER sig=j CSC CONNECT hub 4-0:1.0: port 1, status 0501, change 0001, 480 Mb/s hub 4-0:1.0: debounce: port 1: delay 100ms stable 4 status 0x501 hub 4-0:1.0: port 1 not reset yet, waiting 50ms ehci_hcd 0000:00:1d.7: port 1 full speed --> companion ehci_hcd 0000:00:1d.7: GetStatus port 1 status 003801 POWER OWNER sig=j CONNECTehci_hcd 0000:00:1d.7: GetStatus port 2 status 003002 POWER OWNER sig=se0 CSC hub 4-0:1.0: port 2, status 0000, change 0001, 12 Mb/s ehci_hcd 0000:00:1d.7: GetStatus port 5 status 003002 POWER OWNER sig=se0 CSC hub 4-0:1.0: port 5, status 0000, change 0001, 12 Mb/s uhci_hcd 0000:00:1d.0: port 1 portsc 0093 hub 1-0:1.0: port 1, status 0101, change 0001, 12 Mb/s hub 1-0:1.0: debounce: port 1: delay 100ms stable 4 status 0x101 usb 1-1: new full speed USB device using address 4 usb 1-1: skipped 25 descriptors after interface usb 1-1: skipped 2 descriptors after interface usb 1-1: skipped 1 descriptor after endpoint usb 1-1: skipped 2 descriptors after interface usb 1-1: skipped 1 descriptor after endpoint usb 1-1: skipped 2 descriptors after interface usb 1-1: skipped 1 descriptor after endpoint usb 1-1: skipped 2 descriptors after interface usb 1-1: skipped 1 descriptor after endpoint usb 1-1: skipped 2 descriptors after interface usb 1-1: skipped 1 descriptor after endpoint usb 1-1: skipped 2 descriptors after interface usb 1-1: skipped 1 descriptor after endpoint usb 1-1: skipped 2 descriptors after interface usb 1-1: skipped 1 descriptor after endpoint usb 1-1: skipped 2 descriptors after interface usb 1-1: skipped 1 descriptor after endpoint usb 1-1: skipped 2 descriptors after interface usb 1-1: skipped 1 descriptor after endpoint usb 1-1: skipped 2 descriptors after interface usb 1-1: skipped 1 descriptor after endpoint usb 1-1: skipped 2 descriptors after interface usb 1-1: skipped 1 descriptor after endpoint usb 1-1: skipped 2 descriptors after interface usb 1-1: skipped 1 descriptor after endpoint usb 1-1: skipped 2 descriptors after interface usb 1-1: skipped 1 descriptor after endpoint usb 1-1: skipped 2 descriptors after interface usb 1-1: skipped 1 descriptor after endpoint usb 1-1: skipped 2 descriptors after interface usb 1-1: skipped 1 descriptor after endpoint usb 1-1: skipped 2 descriptors after interface usb 1-1: skipped 1 descriptor after endpoint usb 1-1: skipped 2 descriptors after interface usb 1-1: skipped 1 descriptor after endpoint usb 1-1: skipped 2 descriptors after interface usb 1-1: skipped 1 descriptor after endpoint usb 1-1: skipped 2 descriptors after interface usb 1-1: skipped 1 descriptor after endpoint usb 1-1: skipped 2 descriptors after interface usb 1-1: skipped 1 descriptor after endpoint usb 1-1: skipped 2 descriptors after interface usb 1-1: skipped 1 descriptor after endpoint usb 1-1: skipped 2 descriptors after interface usb 1-1: skipped 1 descriptor after endpoint usb 1-1: skipped 2 descriptors after interface usb 1-1: skipped 1 descriptor after endpoint usb 1-1: new device strings: Mfr=1, Product=2, SerialNumber=0 usb 1-1: default language 0x0409 usb 1-1: Product: SB Audigy 2 NX usb 1-1: Manufacturer: Creative Technology Ltd usb 1-1: hotplug usb 1-1: adding 1-1:1.0 (config #1, interface 0) usb 1-1:1.0: hotplug usb 1-1: adding 1-1:1.1 (config #1, interface 1) usb 1-1:1.1: hotplug usb 1-1: adding 1-1:1.2 (config #1, interface 2) usb 1-1:1.2: hotplug [EMAIL PROTECTED] sk $ After unplugging this is shown: ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001002 POWER sig=se0 CSC hub 4-0:1.0: port 1, status 0100, change 0001, 12 Mb/s ehci_hcd 0000:00:1d.7: GetStatus port 2 status 003002 POWER OWNER sig=se0 CSC hub 4-0:1.0: port 2, status 0000, change 0001, 12 Mb/s ehci_hcd 0000:00:1d.7: GetStatus port 5 status 003002 POWER OWNER sig=se0 CSC hub 4-0:1.0: port 5, status 0000, change 0001, 12 Mb/s uhci_hcd 0000:00:1d.0: port 1 portsc 0088 hub 1-0:1.0: port 1 enable change, status 00000100 [EMAIL PROTECTED] sk $ Is there anything wrong? What about this repeating usb 1-1: skipped 1 descriptor after endpoint usb 1-1: skipped 2 descriptors after interface messages? Thanks Sebastian ____________________________________________________ Aufnehmen, abschicken, nah sein - So einfach ist WEB.DE Video-Mail: http://freemail.web.de/?mc=021200 ------------------------------------------------------- This SF.Net email is sponsored by BEA Weblogic Workshop FREE Java Enterprise J2EE developer tools! Get your free copy of BEA WebLogic Workshop 8.1 today. http://ads.osdn.com/?ad_id=4721&alloc_id=10040&op=click _______________________________________________ [EMAIL PROTECTED] To unsubscribe, use the last form field at: https://lists.sourceforge.net/lists/listinfo/linux-usb-devel
