I added a line with the ids to kaweth.c and I got:
usb 1-2: new full speed USB device using ohci_hcd and address 7
ohci_hcd 0000:00:12.0: GetStatus roothub.portstatus [1] = 0x00100103 PRSC
PPS PES CCS
usb 1-2: ep0 maxpacket = 8
usb 1-2: new device strings: Mfr=2, Product=3, SerialNumber=1
usb 1-2: default language 0x0409
usb 1-2: Product: USB 10M HomePNA Adapter
usb 1-2: Manufacturer: Generic
usb 1-2: SerialNumber: 00E0989BC8B3
usb 1-2: hotplug
usb 1-2: adding 1-2:1.0 (config #1, interface 0)
usb 1-2:1.0: hotplug
kaweth 1-2:1.0: usb_probe_interface
kaweth 1-2:1.0: usb_probe_interface - got id
drivers/usb/net/kaweth.c: Downloading firmware...
drivers/usb/net/kaweth.c: Firmware loaded. I'll be back...
kaweth: probe of 1-2:1.0 failed with error -5
hub 3-0:1.0: state 5 ports 5 chg ffe0 evt 0008
ehci_hcd 0000:00:12.2: GetStatus port 3 status 001002 POWER sig=se0 CSC
hub 3-0:1.0: port 3, status 0100, change 0001, 12 Mb/s
hub 3-0:1.0: debounce: port 3: total 100ms stable 100ms status 0x100
hub 1-0:1.0: state 5 ports 3 chg fff8 evt 0004
ohci_hcd 0000:00:12.0: GetStatus roothub.portstatus [1] = 0x00030100 PESC
CSC PPS
hub 1-0:1.0: port 2, status 0100, change 0003, 12 Mb/s
usb 1-2: USB disconnect, address 7
usb 1-2: usb_disable_device nuking all URBs
usb 1-2: unregistering interface 1-2:1.0
usb 1-2:1.0: hotplug
usb 1-2: unregistering device
usb 1-2: hotplug
hub 1-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x100
hub 3-0:1.0: state 5 ports 5 chg ffe0 evt 0008
ehci_hcd 0000:00:12.2: GetStatus port 3 status 001803 POWER sig=j CSC
CONNECT
hub 3-0:1.0: port 3, status 0501, change 0001, 480 Mb/s
hub 3-0:1.0: debounce: port 3: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:12.2: port 3 full speed --> companion
ehci_hcd 0000:00:12.2: GetStatus port 3 status 003801 POWER OWNER sig=j
CONNECT
hub 1-0:1.0: state 5 ports 3 chg fff8 evt 0004
ohci_hcd 0000:00:12.0: GetStatus roothub.portstatus [1] = 0x00010101 CSC
PPS CCS
hub 1-0:1.0: port 2, status 0101, change 0001, 12 Mb/s
hub 1-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x101
ohci_hcd 0000:00:12.0: GetStatus roothub.portstatus [1] = 0x00100103 PRSC
PPS PES CCS
usb 1-2: new full speed USB device using ohci_hcd and address 8
ohci_hcd 0000:00:12.0: GetStatus roothub.portstatus [1] = 0x00100103 PRSC
PPS PES CCS
usb 1-2: ep0 maxpacket = 8
usb 1-2: device descriptor read/all, error -71
ohci_hcd 0000:00:12.0: GetStatus roothub.portstatus [1] = 0x00100103 PRSC
PPS PES CCS
usb 1-2: new full speed USB device using ohci_hcd and address 9
ohci_hcd 0000:00:12.0: GetStatus roothub.portstatus [1] = 0x00100103 PRSC
PPS PES CCS
usb 1-2: ep0 maxpacket = 8
usb 1-2: device descriptor read/all, error -71
any ideas?
--
Eero
On Wed, Jan 05, 2005 at 08:47:34AM -0800, Stephen J. Gowdy wrote:
> It doesn't look like it gets recongied below, the says "driver=(none)".
> Looking at the working device list there is no listing for this device,
> but there is one close in number spaec (which might mean nothing);
>
> http://www.qbik.ch/usb/devices/showdev.php?id=638
>
> It says you should use the kaweth driver for it. You could try editing the
> source and adding a line for your device (or just loading the driver might
> be enough, if it only uses that table for hotplug).
>
>
> --
> /------------------------------------+-------------------------\
> |Stephen J. Gowdy | SLAC, MailStop 34, |
> |http://www.slac.stanford.edu/~gowdy/ | 2575 Sand Hill Road, |
> |http://calendar.yahoo.com/gowdy | Menlo Park CA 94025, USA |
> |EMail: [EMAIL PROTECTED] | Tel: +1 650 926 3144 |
> \------------------------------------+-------------------------/
>
-------------------------------------------------------
The SF.Net email is sponsored by: Beat the post-holiday blues
Get a FREE limited edition SourceForge.net t-shirt from ThinkGeek.
It's fun and FREE -- well, almost....http://www.thinkgeek.com/sfshirt
_______________________________________________
[email protected]
To unsubscribe, use the last form field at:
https://lists.sourceforge.net/lists/listinfo/linux-usb-users
