On 12/08/05 01:35:37, Alan Stern wrote:
Two things you should try right away: Upgrade to 2.6.12
(2.6.8 is fairly
old by now), and see if there are any BIOS updates
available for your
laptop.
hi, still the same problem. i had upgraded my bios and
had tried kernel 2.6.11
i've installed 2.6.12 with the dmesg appended below.
thanks in advance,
jack
On Thu, 11 Aug 2005, Jack Andrews wrote:
> hi, i'm having troubles getting my usb controller going
on
> my acer travelmate 511t laptop (a member of the
"travelmate
> 510" series).
>
> i've tried all sorts of BIOS settings (although there
> aren't many settings to change)
>
> and i've tried different settings for 'pci' as suggested
in
> the dmesg: pci=biosirq,usepirqmask
>
> but nothing seems to work. fyi, the laptop has a Ali
m5237.
>
> here's the relevant bits of my dmesg (appended below):
>
> ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller
(OHCI)
> Driver (PCI)
> ohci_hcd: block sizes: ed 64 td 64
> PCI: No IRQ known for interrupt pin A of device
> 0000:00:14.0.
> ohci_hcd 0000:00:14.0: Found HC with no IRQ. Check
> BIOS/PCI 0000:00:14.0 setup!
Linux version 2.6.12-1-686 ([EMAIL PROTECTED]) (gcc version
4.0.2 20050806 (prerelease) (Debian 4.0.1-4)) #1 Tue Aug 9
13:00:08 UTC 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000000bff0000 (usable)
BIOS-e820: 000000000bff0000 - 000000000bff8000 (ACPI data)
BIOS-e820: 000000000bff8000 - 000000000c000000 (ACPI NVS)
0MB HIGHMEM available.
191MB LOWMEM available.
On node 0 totalpages: 49136
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 45040 pages, LIFO batch:15
HighMem zone: 0 pages, LIFO batch:1
DMI 2.1 present.
ACPI: RSDP (v000 Acer ) @
0x000fe030
ACPI: RSDT (v001 Acer AN510 0x00000001 Acer
0x00000000) @ 0x0bff0000
ACPI: FADT (v001 Acer AN510 0x00000001 Acer
0x00000000) @ 0x0bff0054
ACPI: BOOT (v001 Acer AN510 0x00000001 Acer
0x00000000) @ 0x0bff002c
ACPI: DSDT (v001 Acer AN510 0x00001000 MSFT
0x0100000a) @ 0x00000000
ACPI: BIOS age (2000) fails cutoff (2001), acpi=force is
required to enable ACPIACPI: Disabling ACPI support
Allocating PCI resources starting at 0c000000 (gap:
0c000000:f4000000)
Built 1 zonelists
Kernel command line: root=/dev/hda1 ro
Local APIC disabled by BIOS -- you can enable it with
"lapic"
mapped APIC to ffffd000 (01181000)
Initializing CPU#0
PID hash table entries: 1024 (order: 10, 16384 bytes)
Detected 332.966 MHz processor.
Using tsc for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 32768 (order: 5, 131072
bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536
bytes)
Memory: 185912k/196544k available (1728k kernel code,
10100k reserved, 721k data, 180k init, 0k highmem)
Checking if this processor honours the WP bit even in
supervisor mode... Ok.
Calibrating delay loop... 655.36 BogoMIPS (lpj=327680)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0183f9ff 00000000
00000000 00000000 00000000 00000000 00000000
CPU: After vendor identify, caps: 0183f9ff 00000000
00000000 00000000 00000000 00000000 00000000
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 128K
CPU: After all inits, caps: 0183f9ff 00000000 00000000
00000040 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: Intel Celeron (Mendocino) stepping 0a
Enabling fast FPU save and restore... done.
Checking 'hlt' instruction... OK.
checking if image is initramfs...it isn't (bad gzip magic
numbers); looks like an initrd
Freeing initrd memory: 5480k freed
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xf0200, last bus=1
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20050309
ACPI: Interpreter disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI: disabled
PnPBIOS: Scanning system for PnP BIOS support...
PnPBIOS: Found PnP BIOS installation structure at 0xc00f6490
PnPBIOS: PnP BIOS version 1.0, entry 0xfa000:0x0, dseg
0xf0000
PnPBIOS: 15 nodes reported by PnP BIOS; 15 recorded by
driver
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
Boot video device is 0000:01:00.0
PCI: IRQ 0 for device 0000:00:14.0 doesn't match PIRQ mask
- try pci=usepirqmaskpnp: 00:08: ioport range 0x1060-0x106f
has been reserved
pnp: 00:08: ioport range 0xf100-0xf13f has been reserved
pnp: 00:08: ioport range 0xf140-0xf15f has been reserved
Simple Boot Flag at 0x6e set to 0x1
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
devfs: 2004-01-31 Richard Gooch ([EMAIL PROTECTED])
devfs: boot_options: 0x0
Initializing Cryptographic API
Activating ISA DMA hang workarounds.
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
PNP: PS/2 Controller [PNP0303,PNP0f13] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 48 ports, IRQ
sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a NS16550A
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024
blocksize
NET: Registered protocol family 2
IP: routing cache hash table of 1024 buckets, 8Kbytes
TCP established hash table entries: 8192 (order: 4, 65536
bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
NET: Registered protocol family 8
NET: Registered protocol family 20
RAMDISK: cramfs filesystem found at block 0
RAMDISK: Loading 5480KiB [1 disk] into ram disk... done.
VFS: Mounted root (cramfs filesystem) readonly.
input: AT Translated Set 2 keyboard on isa0060/serio0
Freeing unused kernel memory: 180k freed
Capability LSM initialized
NET: Registered protocol family 1
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes;
override with idebus=xx
ALI15X3: IDE controller at PCI slot 0000:00:0f.0
ALI15X3: chipset revision 32
ALI15X3: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x78c0-0x78c7, BIOS settings: hda:DMA,
hdb:pio
ide1: BM-DMA at 0x78c8-0x78cf, BIOS settings: hdc:DMA,
hdd:pio
Probing IDE interface ide0...
hda: TOSHIBA MK3018GAS, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: CD-224E, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
Probing IDE interface ide2...
Probing IDE interface ide3...
Probing IDE interface ide4...
Probing IDE interface ide5...
hda: max request size: 128KiB
hda: 58605120 sectors (30005 MB), CHS=58140/16/63, (U)DMA
hda: cache flushes supported
/dev/ide/host0/bus0/target0/lun0: p1 p2 < p5 p6 p7 >
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Adding 562232k swap on /dev/hda5. Priority:-1 extents:1
EXT3 FS on hda1, internal journal
hdc: ATAPI 24X CD-ROM drive, 128kB Cache
Uniform CD-ROM driver Revision: 3.20
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda6, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Synaptics Touchpad, model: 1, fw: 4.0, id: 0x856a1, caps:
0x0/0x0
input: SynPS/2 Synaptics TouchPad on isa0060/serio1
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda7, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
mice: PS/2 mouse device common for all mice
ts: Compaq touchscreen protocol output
Linux Kernel Card Services
options: [pci] [cardbus] [pm]
PCI: Guessed IRQ 9 for device 0000:00:13.0
PCI: Sharing IRQ 9 with 0000:00:13.1
Yenta: CardBus bridge found at 0000:00:13.0 [1025:1002]
Yenta O2: res at 0x94/0xD4: ea/00
Yenta O2: old bridge, not enabling read prefetch / write
burst
Yenta: ISA IRQ mask 0x0cb8, PCI irq 9
Socket status: 30000007
PCI: Guessed IRQ 9 for device 0000:00:13.1
PCI: Sharing IRQ 9 with 0000:00:13.0
Yenta: CardBus bridge found at 0000:00:13.1 [1025:1002]
Yenta: ISA IRQ mask 0x0cb8, PCI irq 9
Socket status: 30000411
usbcore: registered new driver usbfs
usbcore: registered new driver hub
ohci_hcd: 2004 Nov 08 USB 1.1 'Open' Host Controller (OHCI)
Driver (PCI)
PCI: IRQ 0 for device 0000:00:14.0 doesn't match PIRQ mask
- try pci=usepirqmaskPCI: No IRQ known for interrupt pin A
of device 0000:00:14.0. Please try using pci=biosirq.
ohci_hcd 0000:00:14.0: Found HC with no IRQ. Check
BIOS/PCI 0000:00:14.0 setup!ohci_hcd 0000:00:14.0: init
0000:00:14.0 fail, -19
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected ALi M???? chipset
agpgart: AGP aperture is 64M @ 0xe0000000
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x1001
PCI: Guessed IRQ 5 for device 0000:00:08.0
gameport: ES1938 is pci0000:00:08.0/gameport0, io 0x78a4,
speed 1046kHz
ali1535_smbus 0000:00:11.0: SMB device not enabled -
upgrade BIOS?
ali1535_smbus 0000:00:11.0: ALI1535 not detected, module
not inserted.
ali15x3_smbus 0000:00:11.0: ALI15X3_smb region
uninitialized - upgrade BIOS or use force_addr=0xaddr
ali15x3_smbus 0000:00:11.0: ALI15X3 not detected, module
not inserted.
USB Universal Host Controller Interface driver v2.2
Real Time Clock Driver v1.12
input: PC Speaker
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7, dma 1
[PCSPP,TRISTATE,COMPAT,ECP,DMA]
irda_init()
NET: Registered protocol family 23
Floppy drive(s): fd0 is 1.44M
FDC 0 is a National Semiconductor PC87306
lp0: using parport0 (interrupt-driven).
NET: Registered protocol family 10
Disabled Privacy Extensions on device c03391c0(lo)
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 5
cs: IO port probe 0x100-0x4ff: excluding 0x408-0x40f
0x480-0x48f 0x4d0-0x4d7
cs: IO port probe 0x100-0x4ff: excluding 0x408-0x40f
0x480-0x48f 0x4d0-0x4d7
cs: IO port probe 0x800-0x8ff: clean.
cs: IO port probe 0x800-0x8ff: clean.
cs: IO port probe 0xc00-0xcff: clean.
cs: IO port probe 0xc00-0xcff: clean.
cs: IO port probe 0xa00-0xaff: clean.
cs: IO port probe 0xa00-0xaff: clean.
cs: memory probe 0xa0000000-0xa0ffffff: clean.
eth0: Xircom: port 0x300, irq 3, hwaddr 00:10:A4:E5:4D:92
eth0: MII link partner: 45e1
eth0: MII selected
eth0: media 100BaseT, silicon revision 4
NET: Registered protocol family 17
eth0: no IPv6 routers present
-------------------------------------------------------
SF.Net email is Sponsored by the Better Software Conference & EXPO
September 19-22, 2005 * San Francisco, CA * Development Lifecycle Practices
Agile & Plan-Driven Development * Managing Projects & Teams * Testing & QA
Security * Process Improvement & Measurement * http://www.sqe.com/bsce5sf
_______________________________________________
Linux-usb-users@lists.sourceforge.net
To unsubscribe, use the last form field at:
https://lists.sourceforge.net/lists/listinfo/linux-usb-users
