Hello,

I just picked up a pair of Soekris Net6501-50 boxes to upgrade two of my
client's aging m0n0wall installations.I wanted to go dual-wan, so I'll be
migrating them to PFSense.

I didn't realize at the when I placed the order that the storage was mSATA
and not CF based. Needless to say, I don't have an mSATA adapter handy, so I
had to explore alternative means of getting PFSense installed.After much
trial and error, I managed to get both boxes flashed with 2.0 release using
a modified version of what I found here
http://blog.martinshouse.com/2010/05/howto-install-soekris-server-with-pxe.html
.

Now I can get the Soekris boxes to boot up to the point where it attempts to
load the kernel from disk most of the time, then it freezes. I've been able
to get further a few times, but it always seems to crap out on
storage-related issue.

I doubt that both of my brand new mSATA SSDs are bad, it's probably
something I'm doing wrong. I wrote the embedded image (tried both 1GB & 2GB)
by booting to voyage linux PXE and using the command zcat
/tmp/usb/pfsense-image-file.img.gz | dd of=/dev/sda bs=16k as per the
instructions on the PFSense site. Could it be my block size?

I've included a dump of my startup sequence if it helps:

Thanks,
Jim

POST: 0123456789bcefghips1234ajklnopqr,,,tvwxy


comBIOS ver. 1.40a  20110906  Copyright (C) 2000-2011 Soekris Engineering.

net6501

1024 Mbyte Memory                        CPU Atom E6xx 1009 Mhz


Initializing Intel(R) Boot Agent GE v1.3.72
PXE 2.1 Build 089 (WfM 2.0)

SATA AHCI BIOS ver. 0.6 20110902  Copyright (C) 2003-2011 Intel Corporation

Controller Bus#02, Device#06, Function#00: 02 Ports, 01 Devices
  Port-00: Hard Disk,
  Port-01: No device detected

 Slot   Vend Dev  ClassRev Cmd  Stat CL LT HT  Base1    Base2   Int
--------------------------------------------------------------------
00:00:0 8086 4114 06000003 0007 0000 00 00 00 00000000 00000000
00:23:0 8086 8184 06040000 0107 0010 08 00 01 1FFF1000 A0FFA000 10
00:24:0 8086 8185 06040000 0107 0010 08 00 01 3FFF2000 A2FFA100 11
00:25:0 8086 8180 06040000 0107 0010 08 00 01 5FFF4000 A4FFA300 05
00:26:0 8086 8181 06040000 0107 0010 08 00 01 0FFF1000 00FFA000 09
00:31:0 8086 8186 06010000 0003 0000 00 00 80 00000000 00000000
02:02:0 8086 8804 0C031001 0106 0010 00 00 80 A0000900 00000000 09
02:02:1 8086 8805 0C031001 0106 0010 00 00 80 A0000A00 00000000 09
02:02:2 8086 8806 0C031001 0106 0010 00 00 80 A0000B00 00000000 09
02:02:3 8086 8807 0C032001 0106 0010 00 00 80 A0000C00 00000000 09
02:06:0 8086 880B 01060101 0107 0010 00 00 00 00000000 00000000 11
02:08:0 8086 880C 0C031001 0106 0010 00 00 80 A0004400 00000000 10
02:08:1 8086 880D 0C031001 0106 0010 00 00 80 A0004500 00000000 10
02:08:2 8086 880E 0C031001 0106 0010 00 00 80 A0004600 00000000 10
02:08:3 8086 880F 0C032001 0106 0010 00 00 80 A0004700 00000000 10
02:10:1 8086 8811 07000200 0107 0010 00 00 80 00001021 A0004800 09
02:10:2 8086 8812 07000200 0107 0010 00 00 80 00001029 A0004810 09
02:12:2 8086 8817 0C800000 0106 0010 00 00 80 00000000 A0004900 05
02:12:3 8086 8818 0C090000 0106 0010 00 00 80 00000000 A0004A00 05
03:00:0 111D 803A 0604000E 0107 0010 08 00 01 3FFF2000 A2FFA100
05:00:0 8086 10D3 02000000 0107 0010 08 00 00 A1000000 00000000 09
06:00:0 8086 10D3 02000000 0107 0010 08 00 00 A2000000 00000000 10
08:00:0 111D 803A 0604000E 0107 0010 08 00 01 5FFF4000 A4FFA300
10:00:0 8086 10D3 02000000 0107 0010 08 00 00 A3000000 00000000 10
11:00:0 8086 10D3 02000000 0107 0010 08 00 00 A4000000 00000000 11

 1 Seconds to automatic boot.   Press Ctrl-P for entering Monitor.

1  pfSense
2  pfSense

F6 PXE
Boot:  1 #

BIOS 632kB/1047552kB available memory

FreeBSD/i386 bootstrap loader, Revision 1.1
(root@FreeBSD_8.0_pfSense_2.0-snaps.pfsense.org, Tue Sep 13 17:47:07 EDT
2011)
Loading /boot/defaults/loader.conf
/boot/kernel/kernel text=0x8a1d58 data=0x3c9e94+0x9b6a0
syms=[0x4+0x94100+0x4+0xcaf47]
\
Hit [Enter] to boot immediately, or any other key for command prompt.
Booting [/boot/kernel/kernel]...               .
Copyright (c) 1992-2010 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 8.1-RELEASE-p4 #0: Tue Sep 13 18:02:33 EDT 2011
    
root@FreeBSD_8.0_pfSense_2.0-snaps.pfsense.org:/usr/obj./usr/pfSensesrc/src/sys/pfSense_wrap.8.i386
i386
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Genuine Intel(R) CPU        @ 1.00GHz (1000.00-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0x20661  Family = 6  Model = 26  Stepping =
1

Features=0xbfe9fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>

Features2=0x40e3bd<SSE3,DTES64,MON,DS_CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,MOVBE>
  AMD Features=0x20100000<NX,LM>
  AMD Features2=0x1<LAHF>
  TSC: P-state invariant
real memory  = 1073741824 (1024 MB)
avail memory = 1032179712 (984 MB)
ACPI Error: A valid RSDP was not found (20100331/tbxfroot-309)
MPTable: <Soekris  net6501     >
WARNING: Non-uniform processors.
WARNING: Using suboptimal topology.
ioapic0: Assuming intbase of 0
ioapic0 <Version 2.0> irqs 0-23 on motherboard
netisr_init: forcing maxthreads to 1 and bindthreads to 0 for device polling
wlan: mac acl policy registered
ipw_bss: You need to read the LICENSE file in
/usr/share/doc/legal/intel_ipw/.
ipw_bss: If you agree with the license, set legal.intel_ipw.license_ack=1 in
/boot/loader.conf.
module_register_init: MOD_LOAD (ipw_bss_fw, 0xc0710010, 0) error 1
ipw_ibss: You need to read the LICENSE file in
/usr/share/doc/legal/intel_ipw/.
ipw_ibss: If you agree with the license, set legal.intel_ipw.license_ack=1
in /boot/loader.conf.
module_register_init: MOD_LOAD (ipw_ibss_fw, 0xc07100b0, 0) error 1
wpi: You need to read the LICENSE file in /usr/share/doc/legal/intel_wpi/.
wpi: If you agree with the license, set legal.intel_wpi.license_ack=1 in
/boot/loader.conf.
module_register_init: MOD_LOAD (wpi_fw, 0xc0883050, 0) error 1
ipw_monitor: You need to read the LICENSE file in
/usr/share/doc/legal/intel_ipw/.
ipw_monitor: If you agree with the license, set
legal.intel_ipw.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (ipw_monitor_fw, 0xc0710150, 0) error 1
ACPI Error: A valid RSDP was not found (20100331/tbxfroot-309)
ACPI: Table initialisation failed: AE_NOT_FOUND
ACPI: Try disabling either ACPI or apic support.
cryptosoft0: <software crypto> on motherboard
padlock0: No ACE support.
pcib0: <MPTable Host-PCI bridge> pcibus 0 on motherboard
pci0: <PCI bus> on pcib0
pcib1: <PCI-PCI bridge> irq 16 at device 23.0 on pci0
pci1: <PCI bus> on pcib1
pcib2: <PCI-PCI bridge> irq 16 at device 0.0 on pci1
pci2: <PCI bus> on pcib2
pci2: <unknown> at device 0.0 (no driver attached)
pci2: <network, ethernet> at device 0.1 (no driver attached)
pci2: <unknown> at device 0.2 (no driver attached)
ohci0: <OHCI (generic) USB controller> mem 0xa0000900-0xa00009ff irq 19 at
device 2.0 on pci2
ohci0: [ITHREAD]
usbus0: <OHCI (generic) USB controller> on ohci0
ohci1: <OHCI (generic) USB controller> mem 0xa0000a00-0xa0000aff irq 19 at
device 2.1 on pci2
ohci1: [ITHREAD]
usbus1: <OHCI (generic) USB controller> on ohci1
ohci2: <OHCI (generic) USB controller> mem 0xa0000b00-0xa0000bff irq 19 at
device 2.2 on pci2
ohci2: [ITHREAD]
usbus2: <OHCI (generic) USB controller> on ohci2
ehci0: <EHCI (generic) USB 2.0 controller> mem 0xa0000c00-0xa0000cff irq 19
at device 2.3 on pci2
ehci0: [ITHREAD]
usbus3: EHCI version 1.0
usbus3: <EHCI (generic) USB 2.0 controller> on ehci0
pci2: <serial bus, USB> at device 2.4 (no driver attached)
pci2: <base peripheral, SD host controller> at device 4.0 (no driver
attached)
pci2: <base peripheral, SD host controller> at device 4.1 (no driver
attached)
atapci0: <Intel AHCI controller> port 0x1000-0x101f mem
0xa0004000-0xa00043ff irq 17 at device 6.0 on pci2
atapci0: [ITHREAD]
atapci0: AHCI v1.10 controller with 2 3Gbps ports, PM supported
ata2: <ATA channel 0> on atapci0
ata2: [ITHREAD]
ata3: <ATA channel 1> on atapci0
ata3: [ITHREAD]
ohci3: <OHCI (generic) USB controller> mem 0xa0004400-0xa00044ff irq 16 at
device 8.0 on pci2
ohci3: [ITHREAD]
usbus4: <OHCI (generic) USB controller> on ohci3
ohci4: <OHCI (generic) USB controller> mem 0xa0004500-0xa00045ff irq 16 at
device 8.1 on pci2
ohci4: [ITHREAD]
usbus5: <OHCI (generic) USB controller> on ohci4
ohci5: <OHCI (generic) USB controller> mem 0xa0004600-0xa00046ff irq 16 at
device 8.2 on pci2
ohci5: [ITHREAD]
usbus6: <OHCI (generic) USB controller> on ohci5
ehci1: <EHCI (generic) USB 2.0 controller> mem 0xa0004700-0xa00047ff irq 16
at device 8.3 on pci2
ehci1: [ITHREAD]
usbus7: EHCI version 1.0
usbus7: <EHCI (generic) USB 2.0 controller> on ehci1
pci2: <unknown> at device 10.0 (no driver attached)
pci2: <simple comms, UART> at device 10.1 (no driver attached)
pci2: <simple comms, UART> at device 10.2 (no driver attached)
pci2: <simple comms, UART> at device 10.3 (no driver attached)
pci2: <simple comms, UART> at device 10.4 (no driver attached)
pci2: <unknown> at device 12.0 (no driver attached)
pci2: <serial bus> at device 12.1 (no driver attached)
pci2: <serial bus> at device 12.2 (no driver attached)
pci2: <serial bus> at device 12.3 (no driver attached)
pci2: <unknown> at device 12.4 (no driver attached)
pcib3: <PCI-PCI bridge> irq 17 at device 24.0 on pci0
pci3: <PCI bus> on pcib3
pcib4: <PCI-PCI bridge> at device 0.0 on pci3
pci4: <PCI bus> on pcib4
pcib5: <PCI-PCI bridge> at device 2.0 on pci4
pci5: <PCI bus> on pcib5
em0: <Intel(R) PRO/1000 Network Connection 7.2.3> port 0x2000-0x201f mem
0xa1000000-0xa101ffff,0xa1020000-0xa1023fff irq 19 at device 0.0 on pci5
em0: Using MSIX interrupts with 3 vectors
em0: [ITHREAD]
em0: [ITHREAD]
em0: [ITHREAD]
pcib6: <PCI-PCI bridge> at device 3.0 on pci4
pci6: <PCI bus> on pcib6
em1: <Intel(R) PRO/1000 Network Connection 7.2.3> port 0x3000-0x301f mem
0xa2000000-0xa201ffff,0xa2020000-0xa2023fff irq 16 at device 0.0 on pci6
em1: Using MSIX interrupts with 3 vectors
em1: [ITHREAD]
em1: [ITHREAD]
em1: [ITHREAD]
pcib7: <PCI-PCI bridge> at device 4.0 on pci4
pci7: <PCI bus> on pcib7
pcib8: <PCI-PCI bridge> irq 18 at device 25.0 on pci0
pci8: <PCI bus> on pcib8
pcib9: <PCI-PCI bridge> at device 0.0 on pci8
pci9: <PCI bus> on pcib9
pcib10: <PCI-PCI bridge> at device 2.0 on pci9
pci10: <PCI bus> on pcib10
em2: <Intel(R) PRO/1000 Network Connection 7.2.3> port 0x4000-0x401f mem
0xa3000000-0xa301ffff,0xa3020000-0xa3023fff irq 16 at device 0.0 on pci10
em2: Using MSIX interrupts with 3 vectors
em2: [ITHREAD]
em2: [ITHREAD]
em2: [ITHREAD]
pcib11: <PCI-PCI bridge> at device 3.0 on pci9
pci11: <PCI bus> on pcib11
em3: <Intel(R) PRO/1000 Network Connection 7.2.3> port 0x5000-0x501f mem
0xa4000000-0xa401ffff,0xa4020000-0xa4023fff irq 17 at device 0.0 on pci11
em3: Using MSIX interrupts with 3 vectors
em3: [ITHREAD]
em3: [ITHREAD]
em3: [ITHREAD]
pcib12: <PCI-PCI bridge> at device 4.0 on pci9
pci12: <PCI bus> on pcib12
pcib13: <PCI-PCI bridge> irq 19 at device 26.0 on pci0
pci13: <PCI bus> on pcib13
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
cpu0 on motherboard
ata0 at port 0x1f0-0x1f7,0x3f6 irq 14 on isa0
ata0: [ITHREAD]
ata1 at port 0x170-0x177,0x376 irq 15 on isa0
ata1: [ITHREAD]
atrtc0: <AT Real Time Clock> at port 0x70 irq 8 on isa0
ppc0: parallel port not found.
uart0: <16550 or compatible> at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
uart0: [FILTER]
uart0: console (9600,n,8,1)
Timecounter "TSC" frequency 1000004550 Hz quality 800
Timecounters tick every 10.000 msec
IPsec: Initialized Security Association Processing.
usbus0: 12Mbps Full Speed USB v1.0
usbus1: 12Mbps Full Speed USB v1.0
ugen0.1: <(0x8086)> at usbus0
uhub0: <(0x8086) OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0
ugen1.1: <(0x8086)> at usbus1
uhub1: <(0x8086) OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus1
usbus2: 12Mbps Full Speed USB v1.0
usbus3: 480Mbps High Speed USB v2.0
ugen2.1: <(0x8086)> at usbus2
uhub2: <(0x8086) OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus2
ugen3.1: <Intel> at usbus3
uhub3: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus3
uhub0: 1 port with 1 removable, self powered
uhub1: 1 port with 1 removable, self powered
usbus4: 12Mbps Full Speed USB v1.0
usbus5: 12Mbps Full Speed USB v1.0
uhub2: 1 port with 1 removable, self powered
ugen4.1: <(0x8086)> at usbus4
uhub4: <(0x8086) OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus4
ugen5.1: <(0x8086)> at usbus5
uhub5: <(0x8086) OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus5
usbus6: 12Mbps Full Speed USB v1.0
usbus7: 480Mbps High Speed USB v2.0
ugen6.1: <(0x8086)> at usbus6
uhub6: <(0x8086) OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus6
ugen7.1: <Intel> at usbus7
uhub7: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus7
uhub4: 1 port with 1 removable, self powered
uhub5: 1 port with 1 removable, self powered
ad4: 1887MB <TS2GMSA500 20101212> at ata2-master PIO4 SATA 3Gb/s
uhub6: 1 port with 1 removable, self powered
uhub3: 3 ports with 3 removable, self powered
uhub7: 3 ports with 3 removable, self powered
ad4: TIMEOUT - READ retrying (1 retry left) LBA=575
Trying to mount root from ufs:/dev/ufs/pfsense0
Invalid time in real time clock.
Check and reset the date immediately!
ad4: TIMEOUT - READ retrying (1 retry left) LBA=367767
ad4: TIMEOUT - READ retrying (0 retries left) LBA=367767
ad4: FAILURE - READ timed out LBA=367767
g_vfs_done():ufs/pfsense0[READ(offset=188256256, length=2048)]error = 5
exec /sbin/init: error 5
ad4: TIMEOUT - READ retrying (1 retry left) LBA=367767
ad4: TIMEOUT - READ retrying (0 retries left) LBA=367767
ad4: FAILURE - READ timed out LBA=367767
g_vfs_done():ufs/pfsense0[READ(offset=188256256, length=2048)]error = 5
exec /sbin/oinit: error 5
ad4: TIMEOUT - READ retrying (1 retry left) LBA=367767
ad4: TIMEOUT - READ retrying (0 retries left) LBA=367767
ad4: FAILURE - READ timed out LBA=367767
g_vfs_done():ufs/pfsense0[READ(offset=188256256, length=2048)]error = 5
exec /sbin/init.bak: error 5
init: not found in path
/sbin/init:/sbin/oinit:/sbin/init.bak:/rescue/init:/stand/sysinstall
panic: no init
cpuid = 0
Uptime: 1m43s
Cannot dump. Device not defined or unavailable.
Automatic reboot in 15 seconds - press a key on the console to abort
Rebooting...
_______________________________________________
List mailing list
[email protected]
http://lists.pfsense.org/mailman/listinfo/list

Reply via email to