Glad to hear it's working for you Bob. Kurt
On Tue, Jul 31, 2018, at 8:14 AM, Bob Pigford wrote: > Kurt, > > After MANY tries at this, I finally figured out that the filename > errors that RF249.CO was throwing were due to the fact that I had a > dash (-) in my VT root directory name. After I figured that out, it > was clear sailing!> > It is so nice to have REX 4.9 running in VT 1.7. > > Thank you so much for your patient help! > > Bob > > > *From:* M100 [mailto:[email protected]] *On Behalf Of > *Kurt McCullum *Sent:* Sunday, July 29, 2018 7:04 PM *To:* > [email protected] *Subject:* Re: [M100] VirtualT and REX 4.9> > From Virtual-T go to Emulation -> Peripheral Setup. > > Select the radio button that says "Connect to simulated NADSBox". > > Then click the 'Configure' button underneath that radio button. That > will allow you to select the root directory. By default it is the same > directory that Virtual-T is running in.> > That root directory is where you want to drop the three files. > > Hope that helps. > > Kurt > > > On Sun, Jul 29, 2018, at 3:43 PM, Bob Pigford wrote: >> Kurt, >> I know this is a stupid question. Where is my “default TPDD folder” >> under VT1_7? I do not see any folder named TPDD. When using the >> File option “Load file from HD”, the directory that opens is in VT1_6 >> showing my folders, but none indicating TPDD. Please be patient with >> my ignorance here. I am struggling with this as the documentation >> for guys like me is sparse.>> Thank you, >> Bob >> >> *From:* M100 [mailto:[email protected]] *On Behalf Of >> *Kurt McCullum *Sent:* Sunday, July 29, 2018 6:00 PM *To:* >> [email protected] *Subject:* Re: [M100] VirtualT and REX 4.9>> >> Bob, >> >> Sorry for the late reply. Virtual-T installs 4.8. But if you download >> the 4.9 update from here:>> >> bitchin100.com/wiki/images/8/8f/R49_T200_236_rebuild.zip >> >> You can upgrade it to 4.9. >> >> I took all three files and put them in my default TPDD folder. Then >> loaded rf249.co. From BASIC I cleared enough ram so than I could do a >> RUNM "RF249.CO" and then it upgraded Virtual-T to REX 4.9. That's the >> only way I know of to upgrade Virtual-T.>> >> I could send you the rex_flash.bin file from my machine if the >> upgrade doesn't work for you.>> >> Kurt >> >> >> On Sat, Jul 28, 2018, at 9:26 AM, Bob Pigford wrote: >>> Thanks, Kurt. I have tried that but I keep getting REX 4.8 which I >>> had previously installed. Is there a different rex_flash.bin file >>> for 4.9? If so, where might it be obtained?>>> Bob >>> >>> *From:* M100 [mailto:[email protected]] *On Behalf >>> Of *Kurt McCullum *Sent:* Thursday, July 26, 2018 5:47 PM *To:* >>> [email protected] *Subject:* Re: [M100] VirtualT and REX 4.9>>> >>> Bob, >>> >>> I just did a setup of virtual-T with REX to see if I remembered the >>> steps. Here is how I did it.>>> >>> 1) Go to memory options >>> 2) Select REX >>> 3) Click the Create Default Flash button >>> 4) Clock OK >>> 5) Go to BASIC and type CALL 61167,2 >>> >>> That should start the virtual REX manager. >>> >>> From there you load BX images from wherever you have the virtual >>> TPDD set to.>>> >>> Hope that helps. >>> >>> Kurt >>> >>> >>> On Thu, Jul 26, 2018, at 9:16 AM, Bob Pigford wrote: >>>> Hello all. I have struggled to configure VT for REX 4.9. I >>>> understand REXMGR and the OptROM.BX files, but I can’t seem to >>>> figure out which files to have and in which folders they should >>>> reside for the REX 4.9 version (via REXMGR) to appear. I would >>>> like to try again; I use the T200 emulation most of the time.>>>> >>>> My searches for installation instructions have not been successful, >>>> but of course, I am not the sharpest knife in the drawer.>>>> >>>> Where might I find these instructions? >>>> >>>> Thank you! >>>> >>>> Bob >>>> >>> >> >
