On 24/10/16 14:24, John Erlandsson
wrote:
It actually says revision 4.
-------------------------------------------- cat /proc/cpuinfo
--------------------------------------------
processor : 0
model name : ARMv7 Processor rev 4 (v7l)
BogoMIPS : 76.80
Features : half thumb fastmult vfp edsp neon vfpv3 tls
vfpv4 idiva idivt vfpd32 lpae evtstrm crc32
CPU implementer : 0x41
CPU architecture: 7
CPU variant : 0x0
CPU part : 0xd03
CPU revision : 4
processor : 1
model name : ARMv7 Processor rev 4 (v7l)
BogoMIPS : 76.80
Features : half thumb fastmult vfp edsp neon vfpv3 tls
vfpv4 idiva idivt vfpd32 lpae evtstrm crc32
CPU implementer : 0x41
CPU architecture: 7
CPU variant : 0x0
CPU part : 0xd03
CPU revision : 4
processor : 2
model name : ARMv7 Processor rev 4 (v7l)
BogoMIPS : 76.80
Features : half thumb fastmult vfp edsp neon vfpv3 tls
vfpv4 idiva idivt vfpd32 lpae evtstrm crc32
CPU implementer : 0x41
CPU architecture: 7
CPU variant : 0x0
CPU part : 0xd03
CPU revision : 4
processor : 3
model name : ARMv7 Processor rev 4 (v7l)
BogoMIPS : 76.80
Features : half thumb fastmult vfp edsp neon vfpv3 tls
vfpv4 idiva idivt vfpd32 lpae evtstrm crc32
CPU implementer : 0x41
CPU architecture: 7
CPU variant : 0x0
CPU part : 0xd03
CPU revision : 4
Hardware : BCM2709
Revision : a02082
I was rather suspicious about this revision number, or should I
say the one which has already been committed.
However it looks like both are valid and relate to the rpi v3 B
http://elinux.org/RPi_HardwareHistory
Just depends on the manufacturer
Leave it with me for a while and I will set up both revisions as
valid for cpu revision 4 and advise when there is
a package containing it to test
https://github.com/machinekit/machinekit/pull/1085 refers
Will take 30 mins to test build, then needs someone to merge it and
2 - 3 hours for package builds to complete.
Probably best to check the repo tomorrow for the new built packages.
Serial : 00000000376aff9f
-----------------------------------------------------------------------------------------------------------
But I get this error in /var/log/linuxcnc.log when trying to
load hal_gpio:
Oct 23 11:00:23 raspberrypi rtapi:0: rtapi_app_main(hal_gpio):
-22 Invalid argument
Oct 23 11:00:23 raspberrypi msgd:0: hal_lib:1854:rt HAL_GPIO:
ERROR: board revision 5 not supported
This is just because it defaults to 5 if the rev number is not in
the list
I am not worried about breaking my installation. I would like
to try and use a buildroot system eventually. Currently just
testing.
--
website: http://www.machinekit.io
blog: http://blog.machinekit.io
github: https://github.com/machinekit
---
You received this message because you are subscribed to the
Google Groups "Machinekit" group.
To unsubscribe from this group and stop receiving emails from
it, send an email to [email protected].
Visit this group at https://groups.google.com/group/machinekit.
For more options, visit https://groups.google.com/d/optout.
--
website: http://www.machinekit.io
blog: http://blog.machinekit.io
github: https://github.com/machinekit
---
You received this message because you are subscribed to the Google
Groups "Machinekit" group.
To unsubscribe from this group and stop receiving emails from it,
send an email to [email protected].
Visit this group at https://groups.google.com/group/machinekit.
For more options, visit https://groups.google.com/d/optout.
--
website: http://www.machinekit.io blog: http://blog.machinekit.io github: https://github.com/machinekit
---
You received this message because you are subscribed to the Google Groups "Machinekit" group.
To unsubscribe from this group and stop receiving emails from it, send an email to [email protected].
Visit this group at https://groups.google.com/group/machinekit.
For more options, visit https://groups.google.com/d/optout.
|
