On Tue, Jul 13, 2010 at 4:25 PM, vijay singh <[email protected]> wrote: > On Tue, 2010-07-13 at 14:33 +0530, Amit Pundir wrote: >> On Tue, Jul 13, 2010 at 9:19 AM, vijay singh <[email protected]> wrote: >> > On Mon, 2010-07-12 at 17:05 +0300, Ameya Palande wrote: >> >> Hi Vijay, >> >> >> >> On Mon, 2010-07-12 at 09:05 +0200, ext vijay singh wrote: >> >> > I have tried image from below location for DevKit8000: >> >> > >> >> > //http://wiki.meego.com/ARM/Meego_on_Beagleboard_from_scratch#Make_X_start >> >> > >> >> > but i couldn't able to boot kernel. >> >> >> >> Can you post the kernel output from serial console and the .config file >> >> that you used for building this kernel? >> > >> > I have used kernel image from below location : >> > //http://wiki.meego.com/ARM/Meego_on_the_Beagle >> > Check for section "Steps to modify an N900 image for BeagleBoard " >> > >> >> Hi, >> >> Shouldn't you be running devkit8000 kernel instead? >> >> Check the following thread to get the devkit8000 kernel and uboot source >> links: >> http://groups.google.com/group/beagleboard/browse_thread/thread/3e02302066a6c003?pli=1 >> >> regards, >> Amit Pundir >> >> >> > Serial console O/P : >> > >> > ******************************************************************* >> > Texas Instruments X-Loader 1.41 >> > Starting OS Bootloader... >> > U-Boot 1.3.3-svn333 (Sep 10 2009 - 16:49:01) >> > >> > OMAP3530-GP rev 2, CPU-OPP2 L3-165MHz >> > OMAP3 DevKit8000 Board + LPDDR/NAND >> > DRAM: 128 MB >> > NAND: 128 MiB >> > In: serial >> > Out: serial >> > Err: serial >> > >> > Hit any key to stop autoboot: 0 >> > >> > OMAP3 DevKit8000 # setenv bootargs 'console=ttyS2,115200n8 >> > root=/dev/mmcblk0p3 rootdelay=1' >> > OMAP3 DevKit8000 # mmcinit >> > OMAP3 DevKit8000 # fatload mmc 0 82000000 uImage >> > >> > reading uImage >> > >> > 1986880 bytes read >> > >> > OMAP3 DevKit8000 # bootm 82000000 >> > ## Booting kernel from Legacy Image at 82000000 ... >> > Image Name: Linux-2.6.34-beagle >> > Image Type: ARM Linux Kernel Image (uncompressed) >> > Data Size: 1986816 Bytes = 1.9 MB >> > Load Address: 80008000 >> > Entry Point: 80008000 >> > Verifying Checksum ... OK >> > Loading Kernel Image ... OK >> > OK >> > Starting kernel ... >> > Uncompressing Linux... done, booting the kernel. >> > ******************************************************************* >> > >> > After that nothing will happen. >> > >> > Please let me know boot arg are correct ?? >> > or Do i have to use other configuration. >> > >> > If you have working configuration then please send it to me. >> > >> > >> > Regards, >> > vij >> > >> >> >> >> Cheers, >> >> Ameya. > > Hi, > I have tried with one of Beagle board kernel (Working previously) & it's > boot up but still have problem with getting X. > > I have attached boot log. > > In summary i am getting below error (If i will run TWM manager): > ******************************************* > /usr/bin/xsetroot: unable to open display '' > /usr/bin/twm: unable to open display "" > /usr/bin/xterm Xt error: Can't open display: > /usr/bin/xterm: DISPLAY is not set > *******************************************
try following command and see if it works: $ export DISPLAY=:0 regards, Amit Pundir > > Please check. > > Regards, > Vij >> >> >> >> _______________________________________________ >> >> MeeGo-dev mailing list >> >> [email protected] >> >> http://lists.meego.com/listinfo/meego-dev >> > >> > >> > _______________________________________________ >> > MeeGo-dev mailing list >> > [email protected] >> > http://lists.meego.com/listinfo/meego-dev >> > >> _______________________________________________ >> MeeGo-dev mailing list >> [email protected] >> http://lists.meego.com/listinfo/meego-dev > > > _______________________________________________ > MeeGo-dev mailing list > [email protected] > http://lists.meego.com/listinfo/meego-dev > > _______________________________________________ MeeGo-dev mailing list [email protected] http://lists.meego.com/listinfo/meego-dev
