There are three types of 200B discs & callipers and the Hilux callipers only
bolt up to the earlier 10/77 - 7/79 10" Girlock & Sumitomo disc that have
48mm hub height (so I'm told as I've never done it to find out fer sure).
The later Australian Girlocks are only 9.6" and have a 43.mm hub and use
DB1091 Pads.
regards
Terry
-----Original Message-----
From: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED]]On Behalf Of Davidson
Sent: Thursday, 17 August 2000 7:29 PM
To: [EMAIL PROTECTED]
Subject: Re: Stanza Stuts in 1200....
I was going to get some new disc's for it anyhow. So 200b disc's are 9.5"
right. And then these hilux 4spots can be bolted on right. Sounds like a
good combo to me. Thanx again.
Scott
Davo
-----Original Message-----
From: cp <[EMAIL PROTECTED]>
To: [EMAIL PROTECTED] <[EMAIL PROTECTED]>
Date: Wednesday, 16 August, 2000 19:17
Subject: Re: Stanza Stuts in 1200....
>200b struts are very similar to stanza apart from the spring size. The
only
>difference in brakes is the disc size (1" bigger). You can actually swap
>the hub/disc and caliper from the 200b on to the stanza strut for that
>little bit extra...
>
>Chris P
>
>
>-----Original Message-----
>From: Davidson <[EMAIL PROTECTED]>
>To: [EMAIL PROTECTED] <[EMAIL PROTECTED]>
>Date: Wednesday, 16 August 2000 18:59
>Subject: Re: Stanza Stuts in 1200....
>
>
>>Thanks Chris,
>>
>>I have good idea at what i am going to do now. And still have my options
>>open with the 200b struts. For now i will get the staza struts in and see
>>what its like.
>>
>>Scott
>>Davo
>>
>>-----Original Message-----
>>From: cp <[EMAIL PROTECTED]>
>>To: [EMAIL PROTECTED] <[EMAIL PROTECTED]>
>>Date: Tuesday, 15 August, 2000 20:20
>>Subject: Re: Stanza Stuts in 1200....
>>
>>
>>>been there done that.
>>>
>>>Stanza struts fit but you need to drill out the holes on the strut top a
>>>little as the bolts a slightly larger...(think this is right but it may
>>have
>>>been when i was using 1600 tops)
>>>
>>>You need stanza lower arms, ball joints and steering arms. A 120y sway
bar
>>>is also good as there thicker..
>>>
>>>
>>>should then bolt in however. I did this swap onto my 1200 ute and found
>>the
>>>stanza struts to be very tall....Taller than 1600's ones for that
matter..
>>>I cut the spring down to they say at normal 1200 height but that left me
>>>with 2" of travel as the shock bottomed out.
>>>
>>>I would recommend getting shorter inserts...say from a 280zx or 240k and
>>>shortening the whole strut assembly if you want to get a reasonably low
>>ride
>>>height..
>>>
>>>I also offset the tops it get more negitive camber....
>>>
>>>Give me a yell if you need more info...
>>>
>>>Chris P
>>>
>>>
>>>
>>>
>>>-----Original Message-----
>>>From: Davidson <[EMAIL PROTECTED]>
>>>To: [EMAIL PROTECTED] <[EMAIL PROTECTED]>
>>>Date: Tuesday, 15 August 2000 19:45
>>>Subject: Stanza Stuts in 1200....
>>>
>>>
>>>>I have some old Stanza struts and was hoping to fit them to my 1200.
How
>>>do
>>>>i know if there the later model struts?? (1980+). I know i need the
>>stanza
>>>>lower control arms and the castor rods. Is that all or am i missing
>>>>somthing?? All the steering arms connect straight up right?? And the
>sway
>>>>bar connects straight up aswell??
>>>>
>>>>Im trying to get everything ready first before i start pulling the
struts
>>>>out. I dont want to be half way thru it only to find i need some bits
and
>>>>peices. Any help is great :-)
>>>>
>>>>Scott
>>>>Davo
>>>>
>>>
>>
>>
>
--membersozdat-------------------------------------------------------
OZDAT Mailing List Please Note:-
Send (un)subscribe requests to [EMAIL PROTECTED]
Send submissions to [EMAIL PROTECTED]
No unauthorised redistribution of this email
http://www.ozdat.com/ozdatonline/index.htm
http://www.ozdat.com/ozdatonline/listindex.html
http://www.mail-archive.com/[email protected]/
---------------------------------------------------------------------
