For $170... Youch.. I shall spend a day scouring wreckers for one that'll
be just right... Yeah, to save $70, I'd rather do that!!!
Thanks anyway!!!
> -----Original Message-----
> From: [EMAIL PROTECTED]
> [mailto:[EMAIL PROTECTED]]On Behalf Of Mark Ward
> Sent: Wednesday, 23 August 2000 9:19 PM
> To: [EMAIL PROTECTED]
> Subject: Re: Datsun Stanza SSS
>
>
> I went to "Propeller Shaft Services" in Ilma Street, Condell Park (near
> Bankstown). Highly recommended.
>
> Wardy
>
> ----- Original Message -----
> From: "Geordie Smith" <[EMAIL PROTECTED]>
> To: <[EMAIL PROTECTED]>
> Sent: Wednesday, August 23, 2000 9:04 AM
> Subject: RE: Datsun Stanza SSS
>
>
> > I went back to the wrecker yesterday to look at tailshaft options..
> Checked
> > out that car I tore the sway bar off, and it was a 86 model
> skyline... But
> > there were a few pintaras there, I think an 89 model and it was the same
> > one... But mines off the 86 Skyline. I shall measure the
> diameter for you
> > when I find my calipers...
> >
> > Yup, good fix for $35 I reckon..
> >
> > Does anybody know of a place in Sydney who does cut & shut job on a
> > tailshaft. I couldn't find one at the wreckers that was short
> enuf. There
> > was a straight shaft which would have been ok not like the 3-piece one I
> > have, but it had spot-rust on the outstide and I remembered that cross
> > member that guy snapped on the weekend because of rust... and I said to
> > myself "Self, no way is this thing gunna take a pounding like I'm gunna
> give
> > it." I tend to think that I should take this part quite seriously, no
> BS...
> > :)
> >
> >
> > If yours is the s3, then yes the 200sx mounts will bolt up straight onto
> the
> > x-member and give you the right amount of slope the engine likes... I
> think
> > it's about 7-15 degrees on the rocker cover, down side to the passenger
> > side... the top of the rocker cover is almost lever with the
> crease on the
> > firewall and the bonnet clears it with ease.
> >
> > What sort of tailshaft is on your wagon?
> >
> >
> > > -----Original Message-----
> > > From: [EMAIL PROTECTED]
> > > [mailto:[EMAIL PROTECTED]]On Behalf Of Errol Smith
> > > Sent: Tuesday, 22 August 2000 11:26 PM
> > > To: [EMAIL PROTECTED]
> > > Subject: Re: Datsun Stanza SSS
> > >
> > >
> > > Geordie,
> > > The series three Bluebird wagon I just bought has the
> original CA cross
> > > member and uses the 200SX right side engine mount for the SR20. It has
> had
> > > a special front stabiliser made up. I think I like your Skyline
> > > fix better.
> > > Simpler and cheaper.
> > > Cheers
> > > Feral Errol
> > >
> > > ----------
> > > From: Geordie Smith <[EMAIL PROTECTED]>
> > > To: [EMAIL PROTECTED]
> > > Subject: RE: Datsun Stanza SSS
> > > Date: Tuesday, August 22, 2000 9:33
> > >
> > > I have a series 2 bluebird and I'm currently installing an SR20
> > > turbo after
> > > the L20 spat oil & coolant all over the engine bay when it
> blew the head
> > > gasket, cracked the block, shat it'self...
> > >
> > > Quick fix import motor for the S2 bluebird is a Z18t, it's almost
> > > a bolt-in
> > > swap...
> > > If you wanna put in a SR20, then you gotta change the
> cross-member under
> > > the
> > > engine, the sway bar, the tailshaft, etc etc... I've already
> > > done most of
> > > this, just sorting out some ignition problems at the moment, then I'm
> off
> > > to
> > > the plumbers to get some 3" tubes to hang off the turbo and out
> > > the back...
> > > Not a cheap conversion, I've already spent nearly $4000... On a $1500
> > > car!!!! Yikes!
> > >
> > >
> > >
> > > -----Original Message-----
> > > From: [EMAIL PROTECTED]
> > > [mailto:[EMAIL PROTECTED]]On Behalf Of George
> > > Zouglakis
> > > Sent: Monday, 21 August 2000 8:48 PM
> > > To: [EMAIL PROTECTED]
> > > Subject: Re: Datsun Stanza SSS
> > >
> > >
> > > Hey Chris,
> > > The series II Bluebird was released in 1983 (I think!) and
> came
> > > factory with a Bosch reluctor type electronic distributor
> with built in
> > > auto
> > > dwel 016 type coil ignitor. Basically it made a noticable difference
> > > through
> > > out the rev range....especially low end torque. I paid around $120 for
> it
> > > about 6 years ago but I made sure I got the original coil
> with it. (very
> > > important since it looks just like a standard points type coil) As far
> as
> > > the cam is concerned, I can't quite remember its specs, but
> yes, it was
> a
> > > slightly bigger cam with more lift. As far as tuning was
> concerned, the
> > > webber 32/36 was a mongrel of a carbie as far as remembering what you
> > > taught
> > > it! It would run perfectly one day, and like a dog on another. I could
> rev
> > > it to around 5500 with the webber before fuel delivery became an
> > > issue. The
> > > engine is the original unit and has done around 285000 kms,
> due for rest
> > > soon though. I think I may go for an L20...but I'll have to
> think about
> it
> > > since there are really so many import engine options open to datto
> owners
> > > these days.
> > >
> > > George
> > >
> > >
> > > ----- Original Message -----
> > > From: Chris Stagg <[EMAIL PROTECTED]>
> > > To: <[EMAIL PROTECTED]>
> > > Sent: Monday, August 14, 2000 6:05 PM
> > > Subject: Re: Datsun Stanza SSS
> > >
> > >
> > > > Cool!,
> > > >
> > > > You did a fair bit then:), you gave your stanza fuel
> > > injection!!!?, GEEZE
> > > > cool:),
> > > > Don't suppose you could give me a quick rundown on what a Series II
> > > Bluebird
> > > > dizzy is? and what's a stage 1 cam?, just a bigger cam?
> > > > Did you tune your car up a lot as well?, spose u did.
> > > >
> > > >
> > > > Chris
> > > > dreaming of reving his stanza to 6750 rpm...
> > > >
> > > >
> > > >
> > > > George Zouglakis wrote:
> > > >
> > > > > Hey Chris,
> > > > > I've got a 1983 white SSS Stanza which has had various
> work
> > > done
> > > > > to it over the years. In my poorer student days I couldn't
> > > afford to go
> > > too
> > > > > crazy so I ripped off the original carbie and bolted on a webber
> 32/36
> > > and
> > > > > stage 1 cam. It made a significant difference, especially
> up high. I
> > > also
> > > > > installed a series II Bluebird dizzy which also improved
> torque down
> > > low.
> > > > > Extractors came next and some extra usable revs appeared
> up top. The
> > > other
> > > > > way I could have gone (cheaper too) is to bolt in an imported
> > > engine. I
> > > > > didn't stop there either, I did a WOLF EFI conversion on the
> original
> > > L16
> > > > > which made a phenomenal difference everywhere in the rev
> > > range. She how
> > > revs
> > > > > happily up to 6750 rpm while still making heaps of power. I
> > > think I may
> > > have
> > > > > been better off throwing in an imported twin cam engine
> in it though
> > > since
> > > > > the technological difference between the two is huge. It all
> > > comes down
> > > to
> > > > > how much money you want to spend (or who you know) but keep on
> asking
> > > around
> > > > > until you start hearing things that sound possible to you.(and
> within
> > > your
> > > > > budget)
> > > > >
> > > > > George
> > > > >
> > > > > ----- Original Message -----
> > > > > From: Chris Stagg <[EMAIL PROTECTED]>
> > > > > To: <[EMAIL PROTECTED]>
> > > > > Sent: Saturday, August 12, 2000 10:23 PM
> > > > > Subject: Datsun Stanza SSS
> > > > >
> > > > > > Hi,
> > > > > >
> > > > > > I own a Datsun Stanza SSS, 1981 model I think, the following are
> > > things
> > > > > > done to it by previous owner - mag wheels, extractors
> and has been
> > > > > > lowerd a little by cutting the suspension or something, also has
> > > sunroof
> > > > > > and sports steering wheel which may have come standard.
> Found out
> > > today
> > > > > > that it has a duel throat carburetor which I didn't
> think it had!
> > > > > >
> > > > > > Would love to know what I could do to it to make it more beefy=)
> > > > > >
> > > > > >
> > > > >
> > > >
> > > >
> > >
> > >
> > >
> > >
> >
> >
>
>
--membersozdat-------------------------------------------------------
OZDAT Mailing List Please Note:-
Send (un)subscribe requests to [EMAIL PROTECTED]
Send submissions to [EMAIL PROTECTED]
No unauthorised redistribution of this email
http://www.ozdat.com/ozdatonline/index.htm
http://www.ozdat.com/ozdatonline/listindex.html
http://www.mail-archive.com/[email protected]/
---------------------------------------------------------------------
