Are you shortening the diff ? as that is a very wide track [gazelle] for a
1200 ?-----Original Message-----
From: "Errol Smith" <[EMAIL PROTECTED]>
To: <[EMAIL PROTECTED]>
Date: Tuesday, February 06, 2001 9:44
Subject: RE: H190/Stanza
>Rhys,
>They are more than adequate as they are quite short. The Safe Operating
>Speed table put out by Spicer Hardy reckons they OK to 8000 rpm. If you are
>running an overdrive box with a 0.865 fifth this equates to 6920 engine
revs
>in fifth. If you want more than this re tube the shaft.
>Cheers
>Feral Errol
>mailto:[EMAIL PROTECTED]
>http://www.datrats.com.au/
>
>-----Original Message-----
>From: [EMAIL PROTECTED]
>[mailto:[EMAIL PROTECTED]]On Behalf Of R.Hunter
>Sent: Friday, February 25, 2000 12:25 PM
>To: [EMAIL PROTECTED]
>Subject: Re: H190/Stanza
>
>
>I'm currently also putting a gazelle (S-110) disc rear axle into my 1200
>coupe and have found that 180b tailshaft is the right flange pattern.
>I'm worried that the 180b (and all of the indepandent rear) tailshafts may
>not have enough wall thickness, ...... it was never designed to be used
>with a 'moving' live rear axle. (maybe UJs cant cope with angles) can
>anyone shed any light on the subject.?
>Thanks
>Rhys Hunter.
>----------
>From: Errol Smith <[EMAIL PROTECTED]>
>To: [EMAIL PROTECTED]
>Subject: RE: H190/Stanza
>Date: Monday, 5 February 2001 00:23
>
>Nick.
>I used a 180B manual tailshaft. The gazelle rear with an alloy carrier H190
>(X J1500) weighs 58.5 kg and the stock H 165 weighs 59 kg!
>Not bad huh!
>Cheers
>Feral Errol
>mailto:[EMAIL PROTECTED] <mailto:[EMAIL PROTECTED]>
>http://www.datrats.com.au/
>
>-----Original Message-----
>From: [EMAIL PROTECTED]
>[mailto:[EMAIL PROTECTED]]On Behalf Of Ken Abraham
>Sent: Sunday, February 04, 2001 8:19 PM
>To: [EMAIL PROTECTED]
>Subject: H190/Stanza
>
>
>Errol,
>I have just gone to do the final installation of the modified H190 Gazelle
>axle into my Stanza and have struck a snag!
>The tailshaft is too long. it won't bolt up even when the axle is at full
>droop.
>I therefore require a ~10mm (?) shorter tailshaft.
>What did you use when you put the Gazelle axle into a Sunny (Sunny is same
>mechanically as Stanza ?)
>Which tailshaft should I use, Sunny or 180b are top of my list at the
>moment.
>
>Looks like public transport again this week :o
>
>Thanks in advance
>Nick
>1978 Datsun Stanza
>
>--membersozdat-------------------------------------------------------
>OZDAT Mailing List Please Note:-
>Send (un)subscribe requests to [EMAIL PROTECTED]
>Send submissions to [EMAIL PROTECTED]
>No unauthorised redistribution of this email
>http://www.ozdat.com/ozdatonline/index.htm
>http://www.ozdat.com/ozdatonline/listindex.html
>http://www.mail-archive.com/[email protected]/
>---------------------------------------------------------------------
>
>
>
>
--membersozdat-------------------------------------------------------
OZDAT Mailing List Please Note:-
Send (un)subscribe requests to [EMAIL PROTECTED]
Send submissions to [EMAIL PROTECTED]
No unauthorised redistribution of this email
http://www.ozdat.com/ozdatonline/index.htm
http://www.ozdat.com/ozdatonline/listindex.html
http://www.mail-archive.com/[email protected]/
---------------------------------------------------------------------
