i think you will find ( and im prolly wrong and you guys prolly already know this) that the exessive swing is is due to a small rubber grommet disc shaped plug that falls out of the back of the booster this gives the pedal heaps of swing but when put back in its place the swing goes away
just a thought any way my setup is straight 240k front end everything, with the 7/8 M C. and the 180b booster - i want to go to the honda legend rotors and 4 spot toyota hilux calipers on the 240k strut - will the 7/8" MC but good for this or do you think the 13/16 will be a better deal,.?? thanx for the info Leighton ----- Original Message ----- From: "Terry Rudd" <[EMAIL PROTECTED]> To: <[EMAIL PROTECTED]> Sent: Saturday, February 16, 2002 10:55 PM Subject: RE: lOOKING FOR 240 k FRONT END > Leighton, > > I and most others with 200b or 240K Fronts and drums or R31 on the rear have > had nothing but grief with the combination of a 7/8" cylinder and Kiki > Bendix 180B/210/310 booster. You either throw the booster or change the > cylinder for a 13/16" Sunny unit. The 7/8" has to much travel for that > combo. It does depend on what callipers you use, Sumo 2 spots are better and > 4 spot cruiser callipers are good but the single spots have a problem. > > regards > Terry > > -----Original Message----- > From: [EMAIL PROTECTED] > [mailto:[EMAIL PROTECTED]]On Behalf Of Leighton > Sent: Saturday, 16 February 2002 8:02 PM > To: [EMAIL PROTECTED] > Subject: Re: lOOKING FOR 240 k FRONT END > > > what abouit with a 240k front end with a 7/8" master cylinder and 120y/180b > booster > > > Leighton > ----- Original Message ----- > From: "Terry Rudd" <[EMAIL PROTECTED]> > To: <[EMAIL PROTECTED]> > Sent: Saturday, February 16, 2002 1:01 PM > Subject: RE: lOOKING FOR 240 k FRONT END > > > > Leighton, > > > > Pass on the 240K legs, there was a 240K (blue) at Dunkers a couple of > weeks > > back that was complete but the way stuff gets shifted there it's highly > > unlikely to be there - it had a full set of QI lights too. > > > > On R31 rears, some combos work well with just the inbuilt proportioning in > > the master cyl. 200B/R31 with 13/16 Sunny cylinder is one, although you > need > > fairly similar range pads for it to work well. > > > > regards > > Terry > > > > -----Original Message----- > > From: [EMAIL PROTECTED] > > [mailto:[EMAIL PROTECTED]]On Behalf Of Leighton > > Sent: Thursday, 14 February 2002 5:57 PM > > To: [EMAIL PROTECTED] > > Subject: lOOKING FOR 240 k FRONT END > > > > > > I know its a long shot but if any one has got a 240K front end they wanna > > get rid off could you please let me know???? i am looking for one > > > > > > alos im going to put the R31 skyline disc brakes on the rear end of my > > 1600 - to get them to work properly do i need a proportion valve or will > > they work without one??? > > > > > > thanx > > > > Leighton > > > > > > > --membersozdat------------------------------------------------------- OZDAT Mailing List Please Note:- Send (un)subscribe requests to [EMAIL PROTECTED] Send submissions to [EMAIL PROTECTED] No unauthorised redistribution of this email http://www.ozdat.com/ozdatonline/index.htm http://www.ozdat.com/ozdatonline/listindex.html http://www.mail-archive.com/[email protected]/ ---------------------------------------------------------------------
