make sure that rubber grommet is in place in your mastercylinder and floating around the bottom of the booster. cos that makes a lot of difference
Leighton ----- Original Message ----- From: "Andrew Greenbury" <[EMAIL PROTECTED]> To: <[EMAIL PROTECTED]> Sent: Monday, February 18, 2002 10:37 AM Subject: RE: lOOKING FOR 240 k FRONT END > Hi Terry, > > Ahh this sounds familiar to me, as I have 240K with twin spots and > rear drums, with 180b i think booster and 7/8 cylinder, and I have > been quietly wondering why everyone goes on about how good > 240K brakes are :) > > I think I will try and score a sunny master cylinder... > > Thanks again > Andrew > > > Leighton, > > > > I and most others with 200b or 240K Fronts and drums or R31 on the > > rear have had nothing but grief with the combination of a 7/8" > > cylinder and Kiki Bendix 180B/210/310 booster. You either throw the > > booster or change the cylinder for a 13/16" Sunny unit. The 7/8" > > has to much travel for that combo. It does depend on what callipers > > you use, Sumo 2 spots are better and 4 spot cruiser callipers are > > good but the single spots have a problem. > > > > regards > > Terry > > > > -----Original Message----- > > From: [EMAIL PROTECTED] > > [mailto:[EMAIL PROTECTED]]On Behalf Of Leighton > > Sent: Saturday, 16 February 2002 8:02 PM > > To: [EMAIL PROTECTED] > > Subject: Re: lOOKING FOR 240 k FRONT END > > > > > > what abouit with a 240k front end with a 7/8" master cylinder and 120y/180b > > booster > > > > > > Leighton > > ----- Original Message ----- > > From: "Terry Rudd" <[EMAIL PROTECTED]> > > To: <[EMAIL PROTECTED]> > > Sent: Saturday, February 16, 2002 1:01 PM > > Subject: RE: lOOKING FOR 240 k FRONT END > > > > > > > Leighton, > > > > > > Pass on the 240K legs, there was a 240K (blue) at Dunkers a couple of > > weeks > > > back that was complete but the way stuff gets shifted there it's highly > > > unlikely to be there - it had a full set of QI lights too. > > > > > > On R31 rears, some combos work well with just the inbuilt proportioning in > > > the master cyl. 200B/R31 with 13/16 Sunny cylinder is one, although you > > need > > > fairly similar range pads for it to work well. > > > > > > regards > > > Terry > > > > > > -----Original Message----- > > > From: [EMAIL PROTECTED] > > > [mailto:[EMAIL PROTECTED]]On Behalf Of Leighton > > > Sent: Thursday, 14 February 2002 5:57 PM > > > To: [EMAIL PROTECTED] > > > Subject: lOOKING FOR 240 k FRONT END > > > > > > > > > I know its a long shot but if any one has got a 240K front end they wanna > > > get rid off could you please let me know???? i am looking for one > > > > > > > > > alos im going to put the R31 skyline disc brakes on the rear end of my > > > 1600 - to get them to work properly do i need a proportion valve or will > > > they work without one??? > > > > > > > > > thanx > > > > > > Leighton > > > > > > > > > > > > > --membersozdat------------------------------------------------------- OZDAT Mailing List Please Note:- Send (un)subscribe requests to [EMAIL PROTECTED] Send submissions to [EMAIL PROTECTED] No unauthorised redistribution of this email http://www.ozdat.com/ozdatonline/index.htm http://www.ozdat.com/ozdatonline/listindex.html http://www.mail-archive.com/[email protected]/ ---------------------------------------------------------------------
