OOOps ! Stuey, you can come and look at my diff anytime you want. r180 out of a 720 4wd. If i remember i will take a photo for you.
Cheers Jeff http://www.mosport.net http://bookstore.mosport.net -----Original Message----- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] Behalf Of Stuey Roberts Sent: Saturday, 4 June 2005 2:43 PM To: [email protected] Subject: RE: FW: R180 diff into 1600 yeah im in brisbane, all the wreckers i have tried dont have any, i found 1 mgc210 skyline, but diff had been raided already. bastards. what about a 280zx auto, are the a r200 or r180, could i use the shafts out of that? >From: "Terry Rudd" <[EMAIL PROTECTED]> >Reply-To: [email protected] >To: "Ozdat List (Ozdat)" <[email protected]> >Subject: FW: R180 diff into 1600 >Date: Fri, 3 Jun 2005 18:48:32 +1000 > >Stuey, > >You'll get a pair of these 1/2 shafts at any of the larger U-Pull type >wreckers and from Sydney (Blacktown) they'll cost you $40 to $50 - check >the >Unis are good cause they're real exy to replace. There's a couple of good >U-Pulls in Brisbane and I'm sure there's likewise in Melbourne - I can't >recall where you live. > >Regards, >Terry > > > >-----Original Message----- >From: Stuey Roberts [mailto:[EMAIL PROTECTED] >Sent: Thursday, 2 June 2005 9:44 PM >To: [EMAIL PROTECTED] >Subject: RE: R180 diff into 1600 > > >okay, well if i need those, do you have any half shafts around, or does >anybody have any around they can part with, im getting desperate....... >sick > >of not being able to drive my car, i want to drive it a lil bit before i >loose my licence and have to sell it > > > >From: "Terry Rudd" <[EMAIL PROTECTED]> > >To: <[EMAIL PROTECTED]> > >Subject: RE: R180 diff into 1600 > >Date: Thu, 2 Jun 2005 20:52:26 +1000 > > > >Stuey, > > > >I have finally found a pic of a R180 diff in a 1600 - this diff doesn't > >have > >side axles, the shafts just slide straight into the diff 240K/C210 >Skyline > >and 720's are like this but to do it on a 1600 you need 240K/C210 Skyline > >half shafts. > > > > > > > > > >Regards, > >Terry > > > > > > > >-----Original Message----- > >From: [EMAIL PROTECTED] > >[mailto:[EMAIL PROTECTED] On Behalf Of Stuey > >Roberts > >Sent: Tuesday, 31 May 2005 6:35 PM > >To: [email protected] > >Subject: RE: R180 diff into 1600 > > > > > > > >damn i need a digi camera, yeah that is what i have, its a slide in > >shaft which has a bolt hole thru centre, which u bolt the drive shaft > >to, same as an r160, just i used that slide in bit on the r180, but > >cause the 180 is a bigger diff that the 160, those 160 slide in spline > >shaft is to short for the 180 diff. > > > > >From: "Terry Rudd" <[EMAIL PROTECTED]> > > >Reply-To: [email protected] > > >To: <[email protected]> > > >Subject: RE: R180 diff into 1600 > > >Date: Mon, 30 May 2005 22:31:58 +1000 > > > > > >You must have a real old style R180 diff as the 1/2 shafts don't bolt > > >into a > > >R180 diff, they slide into the diff and there aint no plate. The > >exception > > >to the slide in shafts is what came on the 240Z which has a R180 that > >takes > > >the same shafts as a 1600/180B/200B with R160. What's in either side > > >of your R180 - there should be just 2 holes with a splined shaft > > >inside of them - the shafts fit up to it much like how a tailshaft > > >fits onto the back of a gearbox. If it aint got what I've described, > > >then ur got me on this one. > > > > > >What are the shafts off that you intend to use with this R180 diff? > > > > > >-----Original Message----- > > >From: [EMAIL PROTECTED] > > >[mailto:[EMAIL PROTECTED] On Behalf Of Stuey > > >Roberts > > >Sent: Monday, 30 May 2005 6:14 PM > > >To: [email protected] > > >Subject: RE: R180 diff into 1600 > > > > > > > > >its not the shafts that i need, its what the shaft bolts to, the > > >plate on the diff, and they bolt into the diff, you know what i > > >mean?? you have diff, > > > > > >then plate, then shaft, then wheel flange plate... > > > > > > >From: "Terry Rudd" <[EMAIL PROTECTED]> > > > >Reply-To: [email protected] > > > >To: <[email protected]> > > > >Subject: RE: R180 diff into 1600 > > > --membersozdat------------------------------------------------------- OZDAT Mailing List Please Note:- Send (un)subscribe requests to [EMAIL PROTECTED] Send submissions to [email protected] No unauthorised redistribution of this email http://www.ozdat.com/ozdatonline/index.htm http://www.ozdat.com/ozdatonline/listindex.html http://www.mail-archive.com/[email protected]/ ---------------------------------------------------------------------
