When you set the first workpiece do you set it to Z0, then use G50 for all the other parts. For example if the 2nd. part is 2" longer than the first you would set G50 Z2.0??
Colin -----Original Message----- From: Mike Sharp [mailto:[EMAIL PROTECTED]] Sent: Tuesday, October 29, 2002 11:23 AM To: Smartcam Users Group (E-mail) Subject: RE: [mfg-smartcam] Lathe offsets How much different is a 20T compared to a 18T or a 16T control? We are looking into getting another CNC lathe and it would be nice to know what difference there is. Our machines are 6T and 18T controls. Mike -----Original Message----- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of [EMAIL PROTECTED] Sent: Tuesday, October 29, 2002 7:22 AM To: [EMAIL PROTECTED] Subject: RE: [mfg-smartcam] Lathe offsets Oops, I forgot how varied Fanuc lathes can be. How about G50? Same function, different code. =============================== Fred Lauzus, CAM Programming Coordinator High Steel Structures, Incorporated mailto:[EMAIL PROTECTED] http://www.highsteel.com ============================================= -----Original Message----- From: Mike Sharp [mailto:[EMAIL PROTECTED]] Sent: Tuesday, October 29, 2002 10:00 AM To: Smartcam Users Group (E-mail) Subject: RE: [mfg-smartcam] Lathe offsets On my machines G92 is a treading cycle. -----Original Message----- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of [EMAIL PROTECTED] Sent: Tuesday, October 29, 2002 6:36 AM To: [EMAIL PROTECTED] Subject: RE: [mfg-smartcam] Lathe offsets Use the G92 preset command to establish the new Z axis orientation. ============================================= Fred Lauzus, CAM Programming Coordinator High Steel Structures, Incorporated mailto:[EMAIL PROTECTED] <mailto:[EMAIL PROTECTED]> http://www.highsteel.com <http://www.highsteel.com/> ============================================= -----Original Message----- From: Williams, Colin [mailto:[EMAIL PROTECTED]] Sent: Tuesday, October 29, 2002 8:55 AM To: Smartcam Forum (E-mail) Subject: [mfg-smartcam] Lathe offsets We have a Dainichi lathe with a Fanuc control 21-T. I will be programming 4 different parts at one time each with a bar pull, in other words when one part is complete it gets parted off, then we send in the stock stop and pull out the required length for the next piece and so on. Because each part has a different length I would like to program each piece at "Z 0". Our control does not have the option for fixture offsets (G54-G59), which would have been easier. Is there a solution to get each piece to have a "Z 0" Thank you Colin Williams WABCO Freight Car Products Phone: 905-561-8700 ext.227 Fax: 905-561-6616 Email: [EMAIL PROTECTED] WABTEC CORPORATION CONFIDENTIALITY NOTE The content contained in this e-mail transmission is legally privileged and confidential information intended only for the use of the individual or entity named herein. If the reader of this transmission is not the intended recipient, you are hereby notified that any dissemination, distribution, or copying of this transmission is strictly prohibited. ====================================================================== To find out more about this mailing list including how to unsubscribe, send the message "info mfg-smartcam" to [EMAIL PROTECTED] ====================================================================== ====================================================================== To find out more about this mailing list including how to unsubscribe, send the message "info mfg-smartcam" to [EMAIL PROTECTED] ====================================================================== ====================================================================== To find out more about this mailing list including how to unsubscribe, send the message "info mfg-smartcam" to [EMAIL PROTECTED] ====================================================================== ====================================================================== To find out more about this mailing list including how to unsubscribe, send the message "info mfg-smartcam" to [EMAIL PROTECTED] ====================================================================== ====================================================================== To find out more about this mailing list including how to unsubscribe, send the message "info mfg-smartcam" to [EMAIL PROTECTED] ======================================================================
