Hi,
I have a Soekris box equipped with an 8 port serial card I use to manage all my
hardware using cu.
Right now I'm running 4.6 on it, and thought, its time to upgrade, so installed
-current from today ;)
Luckily I did the new installation on a separate CF card, to easily go back.
When I now try to a serial console using a port tty04 or above, then I only get
garbage. For example I call
cu -l /dev/tty0a -s 9600
to get to my sparc, and I just get garbage back when I enter smth.
When I try to connect to my procurve switch,
cu -l /dev/tty09 -s 9600
then, the switch has speed autonegotiation, and connects fine with 1200 baud,
but not the desired 9600 baud.
When I use /dev/tty03 (the first port of the PUC), then it takes the speed
values I give with cu -s correctly, and I can connect fine to the sparc, when
its there connected.
The problems start with tty04, and up to tty0a, I guess all those ports just
only take 1200 bauds.
When I change back the CF card with the 4.6 installed, then all ports are fine
again, so I did not damaged anything while updating.
anyone can help, dmesg below, and ls -l /dev/tty0*
Sebastian
OpenBSD 5.0-current (GENERIC) #118: Tue Dec 20 11:09:21 MST 2011
dera...@i386.openbsd.org:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: Geode(TM) Integrated Processor by AMD PCS ("AuthenticAMD" 586-class) 500
MHz
cpu0: FPU,DE,PSE,TSC,MSR,CX8,SEP,PGE,CMOV,CFLUSH,MMX,MMXX,3DNOW2,3DNOW
real mem = 536408064 (511MB)
avail mem = 517550080 (493MB)
mainbus0 at root
bios0 at mainbus0: AT/286+ BIOS, date 20/80/26, BIOS32 rev. 0 @ 0xfac40
pcibios0 at bios0: rev 2.0 @ 0xf0000/0x10000
pcibios0: pcibios_get_intr_routing - function not supported
pcibios0: PCI IRQ Routing information unavailable.
pcibios0: PCI bus #0 is the last bus
bios0: ROM list: 0xc8000/0xa800
cpu0 at mainbus0: (uniprocessor)
amdmsr0 at mainbus0
pci0 at mainbus0 bus 0: configuration mode 1 (bios)
io address conflict 0x6100/0x100
io address conflict 0x6200/0x200
pchb0 at pci0 dev 1 function 0 "AMD Geode LX" rev 0x31
glxsb0 at pci0 dev 1 function 2 "AMD Geode LX Crypto" rev 0x00: RNG AES
vr0 at pci0 dev 6 function 0 "VIA VT6105M RhineIII" rev 0x96: irq 11, address
00:00:24:c9:d4:98
ukphy0 at vr0 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI 0x004063,
model 0x0034
vr1 at pci0 dev 7 function 0 "VIA VT6105M RhineIII" rev 0x96: irq 5, address
00:00:24:c9:d4:99
ukphy1 at vr1 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI 0x004063,
model 0x0034
vr2 at pci0 dev 8 function 0 "VIA VT6105M RhineIII" rev 0x96: irq 9, address
00:00:24:c9:d4:9a
ukphy2 at vr2 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI 0x004063,
model 0x0034
vr3 at pci0 dev 9 function 0 "VIA VT6105M RhineIII" rev 0x96: irq 12, address
00:00:24:c9:d4:9b
ukphy3 at vr3 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI 0x004063,
model 0x0034
puc0 at pci0 dev 14 function 0 "Sunix 40XX" rev 0x01: ports: 8 com
com3 at puc0 port 0 irq 10: ti16750, 64 byte fifo
com3: probed fifo depth: 32 bytes
com4 at puc0 port 1 irq 10: ti16750, 64 byte fifo
com4: probed fifo depth: 32 bytes
com5 at puc0 port 2 irq 10: ti16750, 64 byte fifo
com5: probed fifo depth: 32 bytes
com6 at puc0 port 3 irq 10: ti16750, 64 byte fifo
com6: probed fifo depth: 32 bytes
com7 at puc0 port 4 irq 10: ti16750, 64 byte fifo
com7: probed fifo depth: 32 bytes
com8 at puc0 port 5 irq 10: ti16750, 64 byte fifo
com8: probed fifo depth: 32 bytes
com9 at puc0 port 6 irq 10: ti16750, 64 byte fifo
com9: probed fifo depth: 32 bytes
com10 at puc0 port 7 irq 10: ti16750, 64 byte fifo
com10: probed fifo depth: 32 bytes
glxpcib0 at pci0 dev 20 function 0 "AMD CS5536 ISA" rev 0x03: rev 3, 32-bit
3579545Hz timer, watchdog, gpio
gpio0 at glxpcib0: 32 pins
pciide0 at pci0 dev 20 function 2 "AMD CS5536 IDE" rev 0x01: DMA, channel 0
wired to compatibility, channel 1 wired to compatibility
wd0 at pciide0 channel 0 drive 0: <SanDisk SDCFH-002G>
wd0: 1-sector PIO, LBA, 1918MB, 3928176 sectors
wd0(pciide0:0:0): using PIO mode 4, DMA mode 2
pciide0: channel 1 ignored (disabled)
ohci0 at pci0 dev 21 function 0 "AMD CS5536 USB" rev 0x02: irq 15, version 1.0,
legacy support
ehci0 at pci0 dev 21 function 1 "AMD CS5536 USB" rev 0x02: irq 15
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 "AMD EHCI root hub" rev 2.00/1.00 addr 1
isa0 at glxpcib0
isadma0 at isa0
com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
com0: console
com1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard
pcppi0 at isa0 port 0x61
spkr0 at pcppi0
nsclpcsio0 at isa0 port 0x2e/2: NSC PC87366 rev 10: GPIO VLM TMS
gpio1 at nsclpcsio0: 29 pins
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
usb1 at ohci0: USB revision 1.0
uhub1 at usb1 "AMD OHCI root hub" rev 1.00/1.00 addr 1
mtrr: K6-family MTRR support (2 registers)
vscsi0 at root
scsibus0 at vscsi0: 256 targets
softraid0 at root
scsibus1 at softraid0: 256 targets
root on wd0a (ddc0d49aadbd07dc.a) swap on wd0b dump on wd0b
crw-rw---- 1 uucp dialer 8, 0 Dec 31 10:27 /dev/tty00
crw-rw---- 1 uucp dialer 8, 1 Dec 31 10:27 /dev/tty01
crw-rw---- 1 uucp dialer 8, 2 Dec 31 10:27 /dev/tty02
crw-rw---- 1 uucp dialer 8, 3 Dec 31 10:27 /dev/tty03
crw-rw---- 1 uucp dialer 8, 4 Dec 31 10:27 /dev/tty04
crw-rw---- 1 uucp dialer 8, 5 Dec 31 10:27 /dev/tty05
crw-rw---- 1 uucp dialer 8, 6 Dec 31 10:27 /dev/tty06
crw-rw---- 1 uucp dialer 8, 7 Dec 31 10:27 /dev/tty07
crw-rw---- 1 uucp dialer 8, 8 Dec 31 10:27 /dev/tty08
crw-rw---- 1 uucp dialer 8, 9 Dec 31 10:27 /dev/tty09
crw-rw---- 1 uucp dialer 8, 10 Dec 31 10:29 /dev/tty0a
crw-rw---- 1 uucp dialer 8, 11 Dec 31 10:27 /dev/tty0b
