On Saturday, December 31, 2011 11:47 CET, "Sebastian Reitenbach"
<[email protected]> wrote:
> On Saturday, December 31, 2011 10:58 CET, "Sebastian Reitenbach"
> <[email protected]> wrote:
>
> > Hi,
> >
> > I have a Soekris box equipped with an 8 port serial card I use to manage
> > all my hardware using cu.
> > Right now I'm running 4.6 on it, and thought, its time to upgrade, so
> > installed -current from today ;)
> > Luckily I did the new installation on a separate CF card, to easily go
> > back.
> >
> > When I now try to a serial console using a port tty04 or above, then I only
> > get garbage. For example I call
> >
> > cu -l /dev/tty0a -s 9600
> > to get to my sparc, and I just get garbage back when I enter smth.
> >
> > When I try to connect to my procurve switch,
> >
> > cu -l /dev/tty09 -s 9600
> >
> > then, the switch has speed autonegotiation, and connects fine with 1200
> > baud, but not the desired 9600 baud.
> >
> > When I use /dev/tty03 (the first port of the PUC), then it takes the speed
> > values I give with cu -s correctly, and I can connect fine to the sparc,
> > when its there connected.
> > The problems start with tty04, and up to tty0a, I guess all those ports
> > just only take 1200 bauds.
> >
> > When I change back the CF card with the 4.6 installed, then all ports are
> > fine again, so I did not damaged anything while updating.
>
> got an off-list reply (thanks), suggesting to try cua(4) instead of tty(4),
> but the problem persists.
and here is a pcidump -v
0:14:0: Sunix 40XX
0x0000: Vendor ID: 1409 Product ID: 7168
0x0004: Command: 0181 Status ID: 0280
0x0008: Class: 07 Subclass: 00 Interface: 02 Revision: 01
0x000c: BIST: 00 Header Type: 00 Latency Timer: 00 Cache Line Size: 00
0x0010: BAR io addr: 0x0000e500/0x0020
0x0014: BAR io addr: 0x0000e520/0x0010
0x0018: BAR io addr: 0x0000e530/0x0008
0x001c: BAR io addr: 0x0000e538/0x0008
0x0020: BAR io addr: 0x0000e540/0x0008
0x0024: BAR io addr: 0x0000e548/0x0008
0x0028: Cardbus CIS: 00000000
0x002c: Subsystem Vendor ID: 1409 Product ID: 5066
0x0030: Expansion ROM Base Address: 00000000
0x0038: 00000000
0x003c: Interrupt Pin: 01 Line: 0a Min Gnt: 00 Max Lat: 00
>
> Sebastian
>
>
>
> >
> > anyone can help, dmesg below, and ls -l /dev/tty0*
> >
> > Sebastian
> >
> > OpenBSD 5.0-current (GENERIC) #118: Tue Dec 20 11:09:21 MST 2011
> > [email protected]:/usr/src/sys/arch/i386/compile/GENERIC
> > cpu0: Geode(TM) Integrated Processor by AMD PCS ("AuthenticAMD" 586-class)
> > 500 MHz
> > cpu0: FPU,DE,PSE,TSC,MSR,CX8,SEP,PGE,CMOV,CFLUSH,MMX,MMXX,3DNOW2,3DNOW
> > real mem = 536408064 (511MB)
> > avail mem = 517550080 (493MB)
> > mainbus0 at root
> > bios0 at mainbus0: AT/286+ BIOS, date 20/80/26, BIOS32 rev. 0 @ 0xfac40
> > pcibios0 at bios0: rev 2.0 @ 0xf0000/0x10000
> > pcibios0: pcibios_get_intr_routing - function not supported
> > pcibios0: PCI IRQ Routing information unavailable.
> > pcibios0: PCI bus #0 is the last bus
> > bios0: ROM list: 0xc8000/0xa800
> > cpu0 at mainbus0: (uniprocessor)
> > amdmsr0 at mainbus0
> > pci0 at mainbus0 bus 0: configuration mode 1 (bios)
> > io address conflict 0x6100/0x100
> > io address conflict 0x6200/0x200
> > pchb0 at pci0 dev 1 function 0 "AMD Geode LX" rev 0x31
> > glxsb0 at pci0 dev 1 function 2 "AMD Geode LX Crypto" rev 0x00: RNG AES
> > vr0 at pci0 dev 6 function 0 "VIA VT6105M RhineIII" rev 0x96: irq 11,
> > address 00:00:24:c9:d4:98
> > ukphy0 at vr0 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI
> > 0x004063, model 0x0034
> > vr1 at pci0 dev 7 function 0 "VIA VT6105M RhineIII" rev 0x96: irq 5,
> > address 00:00:24:c9:d4:99
> > ukphy1 at vr1 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI
> > 0x004063, model 0x0034
> > vr2 at pci0 dev 8 function 0 "VIA VT6105M RhineIII" rev 0x96: irq 9,
> > address 00:00:24:c9:d4:9a
> > ukphy2 at vr2 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI
> > 0x004063, model 0x0034
> > vr3 at pci0 dev 9 function 0 "VIA VT6105M RhineIII" rev 0x96: irq 12,
> > address 00:00:24:c9:d4:9b
> > ukphy3 at vr3 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI
> > 0x004063, model 0x0034
> > puc0 at pci0 dev 14 function 0 "Sunix 40XX" rev 0x01: ports: 8 com
> > com3 at puc0 port 0 irq 10: ti16750, 64 byte fifo
> > com3: probed fifo depth: 32 bytes
> > com4 at puc0 port 1 irq 10: ti16750, 64 byte fifo
> > com4: probed fifo depth: 32 bytes
> > com5 at puc0 port 2 irq 10: ti16750, 64 byte fifo
> > com5: probed fifo depth: 32 bytes
> > com6 at puc0 port 3 irq 10: ti16750, 64 byte fifo
> > com6: probed fifo depth: 32 bytes
> > com7 at puc0 port 4 irq 10: ti16750, 64 byte fifo
> > com7: probed fifo depth: 32 bytes
> > com8 at puc0 port 5 irq 10: ti16750, 64 byte fifo
> > com8: probed fifo depth: 32 bytes
> > com9 at puc0 port 6 irq 10: ti16750, 64 byte fifo
> > com9: probed fifo depth: 32 bytes
> > com10 at puc0 port 7 irq 10: ti16750, 64 byte fifo
> > com10: probed fifo depth: 32 bytes
> > glxpcib0 at pci0 dev 20 function 0 "AMD CS5536 ISA" rev 0x03: rev 3, 32-bit
> > 3579545Hz timer, watchdog, gpio
> > gpio0 at glxpcib0: 32 pins
> > pciide0 at pci0 dev 20 function 2 "AMD CS5536 IDE" rev 0x01: DMA, channel 0
> > wired to compatibility, channel 1 wired to compatibility
> > wd0 at pciide0 channel 0 drive 0: <SanDisk SDCFH-002G>
> > wd0: 1-sector PIO, LBA, 1918MB, 3928176 sectors
> > wd0(pciide0:0:0): using PIO mode 4, DMA mode 2
> > pciide0: channel 1 ignored (disabled)
> > ohci0 at pci0 dev 21 function 0 "AMD CS5536 USB" rev 0x02: irq 15, version
> > 1.0, legacy support
> > ehci0 at pci0 dev 21 function 1 "AMD CS5536 USB" rev 0x02: irq 15
> > usb0 at ehci0: USB revision 2.0
> > uhub0 at usb0 "AMD EHCI root hub" rev 2.00/1.00 addr 1
> > isa0 at glxpcib0
> > isadma0 at isa0
> > com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
> > com0: console
> > com1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
> > pckbc0 at isa0 port 0x60/5
> > pckbd0 at pckbc0 (kbd slot)
> > pckbc0: using irq 1 for kbd slot
> > wskbd0 at pckbd0: console keyboard
> > pcppi0 at isa0 port 0x61
> > spkr0 at pcppi0
> > nsclpcsio0 at isa0 port 0x2e/2: NSC PC87366 rev 10: GPIO VLM TMS
> > gpio1 at nsclpcsio0: 29 pins
> > npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
> > usb1 at ohci0: USB revision 1.0
> > uhub1 at usb1 "AMD OHCI root hub" rev 1.00/1.00 addr 1
> > mtrr: K6-family MTRR support (2 registers)
> > vscsi0 at root
> > scsibus0 at vscsi0: 256 targets
> > softraid0 at root
> > scsibus1 at softraid0: 256 targets
> > root on wd0a (ddc0d49aadbd07dc.a) swap on wd0b dump on wd0b
> > crw-rw---- 1 uucp dialer 8, 0 Dec 31 10:27 /dev/tty00
> > crw-rw---- 1 uucp dialer 8, 1 Dec 31 10:27 /dev/tty01
> > crw-rw---- 1 uucp dialer 8, 2 Dec 31 10:27 /dev/tty02
> > crw-rw---- 1 uucp dialer 8, 3 Dec 31 10:27 /dev/tty03
> > crw-rw---- 1 uucp dialer 8, 4 Dec 31 10:27 /dev/tty04
> > crw-rw---- 1 uucp dialer 8, 5 Dec 31 10:27 /dev/tty05
> > crw-rw---- 1 uucp dialer 8, 6 Dec 31 10:27 /dev/tty06
> > crw-rw---- 1 uucp dialer 8, 7 Dec 31 10:27 /dev/tty07
> > crw-rw---- 1 uucp dialer 8, 8 Dec 31 10:27 /dev/tty08
> > crw-rw---- 1 uucp dialer 8, 9 Dec 31 10:27 /dev/tty09
> > crw-rw---- 1 uucp dialer 8, 10 Dec 31 10:29 /dev/tty0a
> > crw-rw---- 1 uucp dialer 8, 11 Dec 31 10:27 /dev/tty0b
