Hi David, create a file with 512 E5's in it and call it dummy.file for example. Then run mkfs.cpm -f s100ide -b dummy.file -b CPMLDR.COM s100ide.img
This will create the cpm filesystem for you called s100ide.img as long as you have in diskdefs the s100ide definition. This will put the CPMLDR.COM on the boot track in the correct place. Then use cpmcp to copy cpm3.sys and other files on to the filesystem and you should be good to go. I am working on a simple bat file that will start with CPMLDR.COM and CPM3.SYS built for prop con and serial I/O - with unique names. You are prompted for your console type and it will then copy the appropriate CPMLDR.COM and CPM3.SYS to their correct names and then do the rest of the magic (create the image file with cpmldr.com in boot track, cpm3.sys and ccp.com on the filesystem and the cpm3 distribution files will also be copied). I don't think it will be hard to get this running. Hopefully I will have done over the weekend. Need to test it as well. Then will extend for the same combinations for banked CPM. Dave On Wednesday, June 18, 2014 1:29:25 PM UTC-5, David Fry wrote: > > Hi Dave, John > > just a quick update from me. > I have grabbed a few hours over the last couple of days to update the disk > format to comply with cpmtools. > the changes are very minor, basically only the removal of one line of code > (decrements LBA value by one) in each instance of the wrlba routine, this > change > also removes the need for a modified MYIDEROM to serve as a boot platform, > the CF disk can now boot directly from a S100 Z80 Monitor (option 'P'). > I have started to update my documentation and remove obsolete information, > hoping to have this completed by the end of the weekend when I wil upload a > new ZIP file to my N8VEM folder and take down the old one. > > The screenshot below shows the working CPM3 image, the files are as > supplied in the CPM3 distro from http://www.cpm.z80.de/ > The disk image was created using a combination of old and new methods, The > Altair sim was used to create CPMLDR.COM and CPM3.SYS and these were > placed into the disk image using the old method of sector copying. All the > other files were copied into the disk image using cpmtools, the result > being checked in a hex editor and all looks good. > > one step closer to simplifying the process :-) > > regards > > David Fry > On Saturday, June 14, 2014 5:31:49 PM UTC+1, monahanz wrote: > >> Guys, it’s great to see all the progress and uptake this simple little >> IDE board has generated. Thomas in particular congratulations on >> putting so much time and effort into “hammering into shape” the process for >> first time installs. It helps tremendously but I think it will still be >> difficult for some people to do. We all should remember how it was >> when we first started! >> >> >> >> I’m wondering if somebody out there could spend the time writing a >> PC/MSDOS based program to setup a CF card for first time users. If we >> agree the IDE board ports start at 30H, the only variable would be the >> console I/O. This could be either spliced into the final disk image >> with the above program (leaving room in the base code with NOP’s) or by >> answering a Q&A session and inserting code like the old XMODEM programs did. >> >> A CF card is laid down as Dave describes and is checked out. Once the >> image is laid down it can be dumped sector for sector any CF card (no >> holes of course). The image can even include a few CPM programs. Probably >> best to start with a non-banked CPM3 image. This program would run on a >> standard PC, format the CF card and write the image sector by sector. Not >> sure if Windows 7,8 allows you to do that easily but there must be a way. >> >> >> >> This would allow anybody not as sophisticated as some of us, to get going >> right away and allow them to write more elaborate CPM3.SYS files that >> include a FDC, printer etc. in the BIOS for their own hardware. >> >> I think something like this would be a tremendous asset for first time >> S100 users. >> >> >> >> Any volunteers? >> >> John >> >> >> >> >> > -- You received this message because you are subscribed to the Google Groups "N8VEM-S100" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. For more options, visit https://groups.google.com/d/optout.
