Something simple is always best....
i~~ _/) ~~~~ _/) ~~~~ _/) ~~~~ _/) ~~i Tom Lafleur On Dec 19, 2014, at 6:01 AM, Crusty OMO <[email protected]> wrote: Hi Tom, My mind is already thinking of how to add to the firmware for this extra support. The plan is, as per your idea, to have the firmware prompt various ports and wait for human response. Then based on which port the response came, write those addresses to the BIOS area for Console I/O. The problem isn't figuring out which ports, but it's knowing the status bits that work with that port. The Data Available bit and Transmit Busy bit can be any of the 8 bits and in either polarity (1 or 0). While I believe there might be ways to search all these status bits to make the system "learn" how the port is strapped, my dilemma is time. How much time do I want to spend on it. As a compromise, I can do the same prompt and wait method but narrow it down to a few combinations. This will simplify my coding task. This is why I'm looking now for a list of common ports and status bits to load. Cheers, Josh From: [email protected] Subject: Re: [N8VEM-S100:5851] Propeller Console I/O Date: Thu, 18 Dec 2014 22:05:11 -0800 To: [email protected] I was asking for support. My unit was working with John's monitor and tools. Unfortunately I don't have access to my system and can't look at the settings. ~~ _/) ~~~~ _/) ~~~~ _/) ~~~~ _/) ~~ On Dec 18, 2014, at 9:01 PM, Crusty OMO <[email protected]> wrote: Ok, I have finished the last parts, connectors, etc. The board is working! It's a little picky as to what kind of monitor it will run. It only works with 2 of 4 monitors I tried with it. But, that's ok. Now, Rich has indicated one configuration, does anyone else want to share their I/O configuration of this board? Who on the list was asking for the 8080 board to support this Console I/O? Thanks, Josh From: [email protected] To: [email protected] Subject: RE: [N8VEM-S100:5846] Propeller Console I/O Date: Wed, 17 Dec 2014 22:34:57 -0500 Hi Guys, I'm finished building this board, I'm in the final stages to configure. What is the most common address and status configuration? I realize it's configurable to match existing vintage software, but I'm hoping to list a few common setups that I can program in firmware. It's acceptable for more than one, since I can test for Status reaction and/or prompt each configuration for a response. Cheers, Josh -- You received this message because you are subscribed to the Google Groups "N8VEM-S100" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. For more options, visit https://groups.google.com/d/optout. -- You received this message because you are subscribed to the Google Groups "N8VEM-S100" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. For more options, visit https://groups.google.com/d/optout. -- You received this message because you are subscribed to the Google Groups "N8VEM-S100" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. For more options, visit https://groups.google.com/d/optout. -- You received this message because you are subscribed to the Google Groups "N8VEM-S100" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. For more options, visit https://groups.google.com/d/optout. -- You received this message because you are subscribed to the Google Groups "N8VEM-S100" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. For more options, visit https://groups.google.com/d/optout.
