First of all, thank you all for your support. Feels great to have some people with knowledge behind my back. So many replies since I had time to check the group last time that I don't know where to start :)
I do not have a schematic for my design, as it is my own design that I pretty much pull out of my head as I go. That often shown like a bad idea, making me to change a lot of things afterwards. Just like today, I had to rewire the whole 'spider web'. And that was the second time I had to do it! And I have to clear out that I have a common anode resistor for 2 tubes, making a total of 3 anode resistors for all 6 tubes. That means that the current has to be double (resistance cut by half). I hope that it now explains the rounded 8mA (7.74 to be more precise) on the anode resistor. It cuts to two nixies, giving appox 3.87mA peak current to each tube. So then 3.87*sqrt(0.267)=2mA RMS Anyhow, I do believe that I have to use the RMS values when working with multiplexed designs, rather than average. Just like someone already explained why, because of the power dissipation. I really hope it is that way :) Well that's all for now. I hope that my setup with anode resistors is finally done. If not - I still have another week to use all the fancy expensive oscilloscopes! So if anyone doesn't agree with this, please say the word :) Cheers On Mar 16, 9:13 am, Dekatron42 <[email protected]> wrote: > Many manufacturers write that you will have to contact them for the > special curves you need when you are going to multiplex their Nixies > since they do not usually print that information in the databooks. > > These sheets show you that the Nixie will have an increased turn-on > voltage corresponding to the increased current when run in switched > mode. This is the same as when a neon voltage stabilizer tube is used, > the voltage increases somewhat when the current increases, you can > check the OB2 voltage regulator tube for instance. > > The curves for most Nixies when used in multiplexed mode are not > linear so if you can't find those curves you'll have to make the > measurements yourself and take into account the spread between > different Nixies to draw the curve. Some of these special curves have > a voltage span of approximately 10-30V for a certain current through > the Nixie, so there is an upper and a lower limit for the turn-on > voltage corresponding to the current used. > > This book:http://www.oldtimeradio.de/BU7908.php"Electronica 171 - > Elektronische Anzeigebauelemente" by Winfired Müller contains a few of > these curves for the ZM-series of Nixies. > > /Martin > > On 16 mar, 00:55, Cobra007 <[email protected]> wrote: > > > > > > > > > Yes, I think I mentioned "slightly" increase rather than a mayor > > increase. > > > I have measure this on another nixie tube and came to the following > > voltages: > > 0.5mA : 120V > > 1.0mA : 125V > > 1.5mA: 130V > > 2.0mA: 133V > > 3.0mA: 140V > > 4.5mA: 150V > > > His tube current will increase from 2mA to about 7.5mA, so according > > to the above measurements, the increase in tube voltage will be > > playing a role. > > > Michel > > > On Mar 16, 10:06 am, Charles MacDonald <[email protected]> wrote: > > > > On 12-03-15 05:46 AM, Cobra007 wrote: > > > > > So it looks like your resistor is correct. The only thing is that the > > > > voltage across the tube will slightly increase due to the higher > > > > current, so it's not 100% correct but pretty much. > > > > Since we are talking a Neon device, the voltage across the tube will try > > > to stay the same, with the current adjusting if needed. That is why > > > Neon bulbs were used as Voltage reference devices in days of Old. > > > > -- > > > Charles MacDonald Stittsville Ontario > > > [email protected] Just Beyond the > > > Fringehttp://users.trytel.com/~cmacd/tubes.html > > > No Microsoft Products were used in sending this e-mail. -- You received this message because you are subscribed to the Google Groups "neonixie-l" group. To post to this group, send an email to [email protected]. To unsubscribe from this group, send email to [email protected]. For more options, visit this group at http://groups.google.com/group/neonixie-l?hl=en-GB.
