Hi, I keep thinking (possibly wrongly) that SVGA is a 3.3.6 server and that VESA is the 4.x.x server of choice for all those who cannot find a better (i.e. accelerated) one... I may be mistaken but X -configure (or XFree86 -configure for that matter) generates usually something quite useful but it sticks it in /root and calls it XF86Configure.new. i.e. you must rename it and stick it in /etc/X11... Lionel --- Jesper Blomstr�m <[EMAIL PROTECTED]> wrote: > "Sprague, IT3" wrote: > > > > Actually, VESA is probably a better bet than the SVGA server... The only > > chips newer than the Kyro2 that I know of are the GeForce3 and Radeon 7500 > > (8500)... > > > Instead of "XFree86Config -configure" I ran the > "xf86config". I did not choose a specific > Video-chipset/driver from the list. > After that I took a look into the XFree86Config-file and > there it said "Generic VGA". When I then ran "startx" I > got (among other things): > > --- > Fatal server error: > AddScreen/ScreenInit failed for driver 0 > > > When reporting a problem related to a server crash, please > send > the full server output, not just the last messages. > This can be found in the log file > "/var/log/XFree86.0.log". > Please report problems to [EMAIL PROTECTED] > --- > > I tried to change to "SVGA" but I kept on ketting a > message that said something about "Could not load module > SVGA". > > I will go home in about 10 hours and then I will try your > tip about the VESA. > I shall also get some information about the details of > that DamnedConfig-file. > > Thx. > > / Jeppe > > > > > > > > -----Original Message----- > > From: Dummy dummy5 [mailto:[EMAIL PROTECTED]] > > Sent: Wednesday, October 24, 2001 4:10 PM > > To: [EMAIL PROTECTED] > > Subject: Re: [Newbie]Kyro2 > > > > Jesper > > > > Did you tried to use the standard SVGA driver ? > > > > >From: Jesper Blomstrom <[EMAIL PROTECTED]> > > >Reply-To: [EMAIL PROTECTED] > > >To: [EMAIL PROTECTED] > > >Subject: Re: [Newbie]Kyro2 > > >Date: Tue, 23 Oct 2001 07:56:03 +0200 > > > > > >I have tried your tip (XFree86 -configure) and this is > > >what I get: > > > > > > > > >... SNIP > > > > > >(II) Primary Device is: PCI 01:00:0 > > > S3VProbe begin > > >(II) Loading sub module "cirrus_laguna" > > >(II) LoadModule: "cirrus_laguna" > > >(II) Loading > > >/usr/X11R6/lib/modules/drivers/cirrus_laguna.o > > >(II) Module cirrus_laguna: vendor="The XFree86 Project" > > > compiled for 4.1.0, module version = 1.0.0 > > > ABI class: XFree86 Video Driver, version 0.4 > > >(II) Loading sub module "cirrus_alpine" > > >(II) LoadModule: "cirrus_alpine" > > >(II) Loading > > >/usr/X11R6/lib/modules/drivers/cirrus_alpine.o > > >(II) Module cirrus_alpine: vendor="The XFree86 Project" > > > compiled for 4.1.0, module version = 1.0.0 > > > ABI class: XFree86 Video Driver, version 0.4 > > >(--) VMware Guest X Server 10.4.0 - build= > > >(II) ATI: Shared non-ATI VGA in PCI/AGP slot 1:0:0 > > >detected. > > >CYRIX: Device Sections found: 1 > > > > > >Fatal server error: > > > > > >XFree86 has found a valid card configuration. > > >Unfortunately the appropriate data has not been added to > > >xf86PciInfo.h. > > >Please forward 'scanpci -v' output to XFree86 support > > >team. > > > > > >When reporting a problem related to a server crash, please > > >send > > >the full server output, not just the last messages. > > >This can be found in the log file "temp.log2". > > >Please report problems to [EMAIL PROTECTED] > > > > > > > > > > > >... SNIP > > > > > > > > >Any more ideas? > > > > > >/ Jeppe > > > > > > > > >Dummy dummy5 wrote: > > > > > > > > Did you tried: > > > > > > > > "XFree86 -configure" command ? > > > > This will create a XF86Config.new file at /root. Take a look at that > > >file to > > > > figurate the correct video driver. > > > > > > > > >From: Jesper Blomstrom <[EMAIL PROTECTED]> > > > > >Reply-To: [EMAIL PROTECTED] > > > > >To: <[EMAIL PROTECTED]> > > > > >Subject: [Newbie]Kyro2 > > > > >Date: Sun, 21 Oct 2001 21:57:31 +0200 > > > > > > > > > >Hi there! > > > > > > > > > >Prepare for a real newbie-question... > > > > > > > > > >I have recently installed FreeBSD but I didn?t install X from start, > > >that?s > > > > >because > > > > >I wanted to install v.4 and not the older version which was shipped > > >with > > > > >the CD. > > > > > > > > > >Anyway, after having answered a lot of questions about the scanning > > > > >frequency and > > > > >colors and so on I got the question about my video-card. Since I did > > >not > > > > >find > > > > >the correct card I did not chose a specific Video-Card. > > > > > > > > > >When I try to start X with startx I get the following message/obituary > > > > >notice: > > > > > > > > > >Fatal server error: > > > > > > > > > >AddScreen/ScreenInit failed for driver 0 > > > > >X connection to :0.0 broken > > > > >Xauth :(argv):1:bad display name "jepsovitz.chello.se:0" in remove > > >command > > > > > > > > > > > > > > >My Video-Card is a Hercules-card: > > > > >64M 3D Prophet Kyro2 > > > > > > > > > > > > > > >Shall I give up on installing X with my Video-Card or is there a > > >sollution? > > > > > > > > > >Thx in advance! > > > > > > > > > >/ Jeppe > _______________________________________________ > Newbie mailing list > [EMAIL PROTECTED] > *** To unsubscribe , or change message options, see: > http://XFree86.Org/mailman/listinfo/newbie
__________________________________________________ Do You Yahoo!? Make a great connection at Yahoo! Personals. http://personals.yahoo.com _______________________________________________ Newbie mailing list [EMAIL PROTECTED] *** To unsubscribe , or change message options, see: http://XFree86.Org/mailman/listinfo/newbie
