It would not even move. Just kept leaking fluid through the center hole. The seals are probably shot. I ordered a rebuild kit. Now, just a few hours later, I have no pressure on the clutch handle at all. Where is the fluid going? Into the engine? No drips on the floor that I can see.
On Fri, Feb 24, 2012 at 7:08 PM, Kyle Munz <[email protected]> wrote: > Once the slave is removed from the side of the bike you can use the > hydraulic pressure of the line to help press it out. Heating it may help > too. > > -Kyle > > > On Fri, Feb 24, 2012 at 5:17 PM, Ralf Oehlerich <[email protected]>wrote: > >> I cannot find the right one on eBay so I will order the rebuild kit. Not >> sure how I would get the cylinder out, since it is not moving, but I will >> figure it out. >> >> >> On Fri, Feb 24, 2012 at 6:10 PM, Kyle Munz <[email protected]> wrote: >> >>> I don't know if I would go to ebay for one of those. They are fairly >>> easy to rebuild and new parts can still be found fairly cheap. >>> >>> -Kyle >>> On Feb 24, 2012 4:54 PM, "Ralf Oehlerich" <[email protected]> wrote: >>> >>>> I did have the cap off. I am bleeding it with a manual bleeding pump. I >>>> let it sit and now the clutch does not even dis-engage at all. I think the >>>> slave cylinder is leaking. When I had the slave cylinder off and pumped the >>>> clutch, fluid started coming out the center. I know that should not be. >>>> I will get another one on Fleebay. >>>> >>>> On Fri, Feb 24, 2012 at 5:27 PM, home <[email protected]> wrote: >>>> >>>>> i hope your using dot 3 or 4? do you have the reservoir over filled? >>>>> r u bleeding it with the cap off(as u should b)? then let her sit a day >>>>> or >>>>> so and bleed it again? periodically cycle the lever. >>>>> >>>>> On Fri, Feb 24, 2012 at 5:21 PM, Ralf Oehlerich <[email protected] >>>>> > wrote: >>>>> >>>>>> I just installed a used Clutch master cylinder on my 83 NH650 and >>>>>> the clutch does not dis-engage the gears completely. I can hold the bike >>>>>> in >>>>>> gear with the clutch pulled, but I cannot shift it back into Neutral. I >>>>>> have to turn the bike off to do that. Is there any way to adjust the >>>>>> clutch >>>>>> travel? I flushed the system properly and the clutch grabs as soon as you >>>>>> let it come out just a little. >>>>>> >>>>>> Thanks, >>>>>> >>>>>> -- >>>>>> You received this message because you are subscribed to the Google >>>>>> Groups "Nighthawk Motorcycle Lovers!" group. >>>>>> To post to this group, send email to >>>>>> [email protected]. >>>>>> To unsubscribe from this group, send email to >>>>>> [email protected]. >>>>>> For more options, visit this group at >>>>>> http://groups.google.com/group/nighthawk_lovers?hl=en. >>>>>> >>>>> >>>>> -- >>>>> You received this message because you are subscribed to the Google >>>>> Groups "Nighthawk Motorcycle Lovers!" group. >>>>> To post to this group, send email to [email protected] >>>>> . >>>>> To unsubscribe from this group, send email to >>>>> [email protected]. >>>>> For more options, visit this group at >>>>> http://groups.google.com/group/nighthawk_lovers?hl=en. >>>>> >>>> >>>> -- >>>> You received this message because you are subscribed to the Google >>>> Groups "Nighthawk Motorcycle Lovers!" group. >>>> To post to this group, send email to [email protected]. >>>> To unsubscribe from this group, send email to >>>> [email protected]. >>>> For more options, visit this group at >>>> http://groups.google.com/group/nighthawk_lovers?hl=en. >>>> >>> -- >>> You received this message because you are subscribed to the Google >>> Groups "Nighthawk Motorcycle Lovers!" group. >>> To post to this group, send email to [email protected]. >>> To unsubscribe from this group, send email to >>> [email protected]. >>> For more options, visit this group at >>> http://groups.google.com/group/nighthawk_lovers?hl=en. >>> >> >> -- >> You received this message because you are subscribed to the Google Groups >> "Nighthawk Motorcycle Lovers!" group. >> To post to this group, send email to [email protected]. >> To unsubscribe from this group, send email to >> [email protected]. >> For more options, visit this group at >> http://groups.google.com/group/nighthawk_lovers?hl=en. >> > > -- > You received this message because you are subscribed to the Google Groups > "Nighthawk Motorcycle Lovers!" group. > To post to this group, send email to [email protected]. > To unsubscribe from this group, send email to > [email protected]. > For more options, visit this group at > http://groups.google.com/group/nighthawk_lovers?hl=en. > -- You received this message because you are subscribed to the Google Groups "Nighthawk Motorcycle Lovers!" group. To post to this group, send email to [email protected]. To unsubscribe from this group, send email to [email protected]. For more options, visit this group at http://groups.google.com/group/nighthawk_lovers?hl=en.
