Hi, do a "cat /tmp/sysinfo/*" on the unit please ...
John On 19/07/2014 20:52, Paul Blazejowski wrote: > John, > > any update on this issue? i strongly believe that the hard-coded > wndr4300 string somewhere in the source is the culprit of the > problem since the wndr3700v4 board_detection is identified as > wndr4300 thus the sysupgrade works for 4300 but not for 3700v4. > > Regards, -paul > > On Tue, 2014-06-24 at 23:15 +0200, John Crispin wrote: >> >> On 24/06/2014 22:43, Paul Blazejowski wrote: >>> i get "The uploaded image file does not contain a supported >>> format. Make sure that you choose the generic image format for >>> your platform." from web interface. >>> >>> this is what i have: >>> >>> -rw-r--r-- 1 diffie diffie 8919040 2014-06-24 15:58 >>> bin/ar71xx/openwrt-ar71xx-nand-wndr3700v4-squashfs-sysupgrade.tar >>> >>> >>> should i push it from shell using sysupgrade script? >>> >> >> it will work from shell, i will look into why it fails via >> webui. >> >> >> >> >> >>> thanks! >>> >>> >>> On Tue, 2014-06-24 at 22:32 +0200, John Crispin wrote: >>>> >>>> On 24/06/2014 22:25, Paul Blazejowski wrote: >>>>> Hi again, >>>>> >>>>> thanks for the tftp fix, flushing just became so much >>>>> faster and easier. >>>>> >>>>> Tested trunk r41336 after your jffs2 fix and the image >>>>> boots fine, restored my configuration changes, rebooted the >>>>> router and all changes are saved now. I will post the >>>>> working dmesg to the ticket at >>>>> https://dev.openwrt.org/ticket/16840 but it is safe to say >>>>> that you can close it ;-) now. >>>>> >>>>> Sysupgrade image(s) for 3700v4 and 4300 do not work now, >>>>> guess this is next on the list... >>>>> >>>> >>>> i tested 4300 and it works. you need to use the >>>> *-ubi-sysupgrade.tar file. >>>> >>>> >>>> >>>> >>>>> Thank you, -paul >>>>> >>>>> On Tue, 2014-06-24 at 20:18 +0200, John Crispin wrote: >>>>>> >>>>>> On 24/06/2014 19:05, Paul Blazejowski wrote: >>>>>>> John, >>>>>>> >>>>>>> Yes i use the reset with pin and from there i tftp the >>>>>>> original firmware from netgear after that i go to the >>>>>>> gui and upload the open-wrt image because the router >>>>>>> will not accept the wndr3700v4 image (there's a >>>>>>> cosmetic fix for that, i created a patch that someone >>>>>>> from the forums has sent months ago to this list but it >>>>>>> was never accepted...) >>>>>>> https://dev.openwrt.org/ticket/16840 >>>>>>> >>>>>>> With that patch tftp'ing the >>>>>>> openwrt-ar71xx-nand-wndr3700v4-ubi-factory.img works >>>>>>> without need to flash the original firmware. >>>>>>> >>>>>>> If there's another method that can be used to flash the >>>>>>> image(s) please let me know i would want to try any >>>>>>> alternative ways of flashing and could learn a thing or >>>>>>> two in the process as well ;-) >>>>>>> >>>>>>> Thank you, -paul >>>>>> >>>>>> >>>>>> Hi, >>>>>> >>>>>> i just pushed the V vs v fix and another fix that >>>>>> removes the jffs2 magic. i think this might have been the >>>>>> cause of the problems. please retry with current trunk >>>>>> and let me know if the problem is gone or still there >>>>>> >>>>>> John _______________________________________________ >>>>>> openwrt-devel mailing list >>>>>> openwrt-devel@lists.openwrt.org >>>>>> https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel >>>>>> >>>>>> >>>>>> >>>>>> >> >>>>>> _______________________________________________ openwrt-devel >>>>>> mailing list openwrt-devel@lists.openwrt.org >>>>>> https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel >>>> >>>>>> >> >>>>>> _______________________________________________ >>>> openwrt-devel mailing list openwrt-devel@lists.openwrt.org >>>> https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel _______________________________________________ openwrt-devel mailing list openwrt-devel@lists.openwrt.org https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel