you could use a opamp like a buffer or schimitt triger (first is
analog, the second is 'digital')

first check what´s the max/min voltage and select a right buffer opamp
(it´s not isolate like double coil transformers, or optocouplers)
if you want isolation, use a optocoupler or a isolated transformers
(double coil transformers normally)
if you want less voltage you can use zener diodes to cut max voltage
(check what´s the current you will use)

check that relay is not only a on/off circuit, it have a time to turn
on, and a time to turn off, it´s like a big digital output lowpass
filter
if your circuit is very fast maybe you will need a rc filter (low pass filter)
opamp with buffer configuration is usual in analog signals, schmitt
triger are usual in digital signals, there´s cmos/ttl buffers that
make the same job like schimitt triger but with diferent voltage
levels
check:

http://en.wikipedia.org/wiki/Schmitt_trigger
http://en.wikipedia.org/wiki/Buffer_amplifier

here have many usual components to eletronic with boards and devices included:
http://www.mikroe.com/eng/products/view/208/mikrobuffer-board/
http://www.mikroe.com/eng/products/view/209/mikrobuffer-proto-board/
http://www.mikroe.com/eng/categories/view/41/various-boards/

Em 11 de março de 2012 11:45, Patryk <[email protected]> escreveu:
> Dnia 11.03.2012 o 14:47 Chris Lautre <[email protected]> Chris
> Lautre <[email protected]> napisał(a):
>
>> Hi
>>
>> A while ago I saw some discussion about a Vibration sensor.
>> I have found an adjustable one that works great:
>> http://www.assemtech.co.uk/
>> There are 2 models NPN(PDS1000-1) and PNP(PDS1000-2) output.
>> They are about 40 GBP.
>>
>> I have the circuit below working fine.
>> The DS2406 reads the Relay open/close.
>> I know there must be a way of reading the output without using the relay.
>> (My circuit design knowledge is a bit limited to say the least)
>> Can anyone suggest a suitable circuit?
>
> I'm not an expert myself. I would use a optoisolator. Those are cheap and
> draw less power than a relay.
> http://en.wikipedia.org/wiki/Opto-isolator
>
> Here's one 4N33 it about $1 and you will need some resistors
> http://www.me.umn.edu/courses/me2011/arduino/technotes/4N33.pdf
>
> Look at the page 4 on the left there is example of a circuit.
> However the one thing I'm not sure if this particular one(4N33) would run
> 5V on the detector side. If you have some local electronics shop I think
> they will give you one suitable for 5V.
>
> Or maybe the 6N138 can be supplied with 5V on detector side.
>
> I never used those but once built one optoisolator from a diode and
> phototransistor an put them in a black shrinktube. If your local shop does
> not have optoisolaotrs(optocouplers) the will certainly have a
> phototransisotr(which looks like a LED)
>
>
> --
> p4trykx
>
> ------------------------------------------------------------------------------
> Virtualization & Cloud Management Using Capacity Planning
> Cloud computing makes use of virtualization - but cloud computing
> also focuses on allowing computing to be delivered as a service.
> http://www.accelacomm.com/jaw/sfnl/114/51521223/
> _______________________________________________
> Owfs-developers mailing list
> [email protected]
> https://lists.sourceforge.net/lists/listinfo/owfs-developers



-- 
Roberto Spadim
Spadim Technology / SPAEmpresarial

------------------------------------------------------------------------------
Virtualization & Cloud Management Using Capacity Planning
Cloud computing makes use of virtualization - but cloud computing 
also focuses on allowing computing to be delivered as a service.
http://www.accelacomm.com/jaw/sfnl/114/51521223/
_______________________________________________
Owfs-developers mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/owfs-developers

Reply via email to