http://www.datasheetcatalog.org/datasheet/philips/74LVC14APWDH.pdf
Hex inverting Schmitt-trigger with 5V tolerant input



Em 11 de março de 2012 12:44, Roberto Spadim <[email protected]> escreveu:
> you could use a opamp like a buffer or schimitt triger (first is
> analog, the second is 'digital')
>
> first check what´s the max/min voltage and select a right buffer opamp
> (it´s not isolate like double coil transformers, or optocouplers)
> if you want isolation, use a optocoupler or a isolated transformers
> (double coil transformers normally)
> if you want less voltage you can use zener diodes to cut max voltage
> (check what´s the current you will use)
>
> check that relay is not only a on/off circuit, it have a time to turn
> on, and a time to turn off, it´s like a big digital output lowpass
> filter
> if your circuit is very fast maybe you will need a rc filter (low pass filter)
> opamp with buffer configuration is usual in analog signals, schmitt
> triger are usual in digital signals, there´s cmos/ttl buffers that
> make the same job like schimitt triger but with diferent voltage
> levels
> check:
>
> http://en.wikipedia.org/wiki/Schmitt_trigger
> http://en.wikipedia.org/wiki/Buffer_amplifier
>
> here have many usual components to eletronic with boards and devices included:
> http://www.mikroe.com/eng/products/view/208/mikrobuffer-board/
> http://www.mikroe.com/eng/products/view/209/mikrobuffer-proto-board/
> http://www.mikroe.com/eng/categories/view/41/various-boards/
>
> Em 11 de março de 2012 11:45, Patryk <[email protected]> escreveu:
>> Dnia 11.03.2012 o 14:47 Chris Lautre <[email protected]> Chris
>> Lautre <[email protected]> napisał(a):
>>
>>> Hi
>>>
>>> A while ago I saw some discussion about a Vibration sensor.
>>> I have found an adjustable one that works great:
>>> http://www.assemtech.co.uk/
>>> There are 2 models NPN(PDS1000-1) and PNP(PDS1000-2) output.
>>> They are about 40 GBP.
>>>
>>> I have the circuit below working fine.
>>> The DS2406 reads the Relay open/close.
>>> I know there must be a way of reading the output without using the relay.
>>> (My circuit design knowledge is a bit limited to say the least)
>>> Can anyone suggest a suitable circuit?
>>
>> I'm not an expert myself. I would use a optoisolator. Those are cheap and
>> draw less power than a relay.
>> http://en.wikipedia.org/wiki/Opto-isolator
>>
>> Here's one 4N33 it about $1 and you will need some resistors
>> http://www.me.umn.edu/courses/me2011/arduino/technotes/4N33.pdf
>>
>> Look at the page 4 on the left there is example of a circuit.
>> However the one thing I'm not sure if this particular one(4N33) would run
>> 5V on the detector side. If you have some local electronics shop I think
>> they will give you one suitable for 5V.
>>
>> Or maybe the 6N138 can be supplied with 5V on detector side.
>>
>> I never used those but once built one optoisolator from a diode and
>> phototransistor an put them in a black shrinktube. If your local shop does
>> not have optoisolaotrs(optocouplers) the will certainly have a
>> phototransisotr(which looks like a LED)
>>
>>
>> --
>> p4trykx
>>
>> ------------------------------------------------------------------------------
>> Virtualization & Cloud Management Using Capacity Planning
>> Cloud computing makes use of virtualization - but cloud computing
>> also focuses on allowing computing to be delivered as a service.
>> http://www.accelacomm.com/jaw/sfnl/114/51521223/
>> _______________________________________________
>> Owfs-developers mailing list
>> [email protected]
>> https://lists.sourceforge.net/lists/listinfo/owfs-developers
>
>
>
> --
> Roberto Spadim
> Spadim Technology / SPAEmpresarial



-- 
Roberto Spadim
Spadim Technology / SPAEmpresarial

------------------------------------------------------------------------------
Virtualization & Cloud Management Using Capacity Planning
Cloud computing makes use of virtualization - but cloud computing 
also focuses on allowing computing to be delivered as a service.
http://www.accelacomm.com/jaw/sfnl/114/51521223/
_______________________________________________
Owfs-developers mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/owfs-developers

Reply via email to