Fabrice....Derek..anyone..
Help needed..
________________________________
From: frank muriuki <[email protected]>
To: "[email protected]"
<[email protected]>
Sent: Monday, July 8, 2013 8:53 AM
Subject: Re: [PacketFence-users] Change of Vlans not working
Hi,
The port configuration is for the end user. The mac-address belongs to one of
the end user's workstation being used for testing.
Regards,
Frank
________________________________
From: Fabrice Durand <[email protected]>
To: [email protected]
Sent: Sunday, July 7, 2013 10:23 PM
Subject: Re: [PacketFence-users] Change of Vlans not working
Hi ,
if the mac address set in the port configuration is the same as your
device then you will never receive any snmp trap.
Regards
Fabrice
Le 2013-07-07 13:39, frank muriuki a écrit :
>
>
> Hi Fabrice,
>
> Would u kindly explain why? is there a problem with the MAC?
>
> ------------------------------
> On Sat, Jul 6, 2013 11:36 AM PDT Fabrice Durand wrote:
>
>> What is 0025.1185.e79f ?
>> If it's the device mac address you will never receive a trap.
>>
>> Regards
>> Fabrice
>>
>> Le 2013-07-06 06:34, frank muriuki a écrit :
>>> Hi guyz,
>>>
>>> I need some help here, i have done my initial packetfence configuration
>>> defining the Management, Registration and Isolation Vlan. I have as well
>>> configured snmp v2 on both the Packetfence and the Cisco 2960 switch. I
>>> have defined the
Mac-Detection vlan same as Isolation vlan. Its the vlan i have configured on
the user interface of the switch as shown below;
>>>
>>> Registration Vlan= Vlan 10
>>> Isolation Vlan = Vlan 20
>>> Mac-Detection Vlan = Vlan 20
>>>
>>> interface GigabitEthernet0/3
>>> switchport access vlan 20
>>> switchport mode access
>>> switchport port-security maximum 1 vlan access
>>> switchport port-security
>>> switchport port-security violation restrict
>>> switchport port-security mac-address 0025.1185.e79f
>>> spanning-tree portfast
>>> end
>>>
>>> ECS-ASW-FL1#sh run | i snmp
>>> snmp-server community Pass123 RW 15
>>> snmp-server enable traps port-security
>>> snmp-server enable traps
port-security trap-rate 1
>>> snmp-server host 10.10.0.10 version 2c Pass123 port-security
>>> snmp-server manager
>>>
>>> ECS-ASW-FL1#sh run | i access-l
>>> access-list 15 permit 10.10.0.10 log
>>>
>>> When i start the user computer i am redirected to the login page and issued
>>> ip on vlan 20 via dhcp. However when i input my credetials i get the error
>>> wrong username/password.
>>> When i manually set the computer as registered, i am redirected to a page
>>> that states 'you network should be enabled within a minute or two...' and
>>> nothing happens even after reboot.
>>>
>>> snmpwalk works but running snmptrapd.log nothing is displayed
>>>
>>> What or where would i be going wrong? Help me out here brilliants!
>>>
>>> Regards,
>>>
Frank
>>>
>>>
>>> ------------------------------------------------------------------------------
>>> This SF.net email is sponsored by Windows:
>>>
>>> Build for Windows Store.
>>>
>>> http://p.sf.net/sfu/windows-dev2dev
>>>
>>>
>>> _______________________________________________
>>> PacketFence-users mailing list
>>> [email protected]
>>> https://lists.sourceforge.net/lists/listinfo/packetfence-users
>
> ------------------------------------------------------------------------------
> This SF.net
email is sponsored by Windows:
>
> Build for Windows Store.
>
> http://p.sf.net/sfu/windows-dev2dev
> _______________________________________________
> PacketFence-users mailing list
> [email protected]
> https://lists.sourceforge.net/lists/listinfo/packetfence-users
------------------------------------------------------------------------------
This SF.net email is sponsored by Windows:
Build for Windows Store.
http://p.sf.net/sfu/windows-dev2dev
_______________________________________________
PacketFence-users
mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/packetfence-users
------------------------------------------------------------------------------
See everything from the browser to the database with AppDynamics
Get end-to-end visibility with application monitoring from AppDynamics
Isolate bottlenecks and diagnose root cause in seconds.
Start your free trial of AppDynamics Pro today!
http://pubads.g.doubleclick.net/gampad/clk?id=48808831&iu=/4140/ostg.clktrk
_______________________________________________
PacketFence-users mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/packetfence-users
