Ok,

You want high voltage?

You want arcs and sparks?

You want Tesla Coils?

May I direct you to the person known as Mr. Arcs and Sparks.

I have an old friend named Bill Wysock who happens to be one of the worlds
premier Tesla Coil builders.

You can see a very small sampling of some of his work at his web site,
www.ttr.com .

Be sure to look at the pictures of the firing of the Model 10 and the Model
13.

Yes. I was there during some of the construction and testing of the Model 12
and also the Model 13, as well as a number of the smaller units. The firing
of the Model 13 at the KRLA Radio Station Site (near the city of Arcadia in
Southern California) was absolutely awesome, and totally beyond what you can
even begin to imagine based only on these photographs.

JaMi

----- Original Message -----
From: "Thomas" <[EMAIL PROTECTED]>
To: "'Protel EDA Forum'" <[EMAIL PROTECTED]>
Sent: Thursday, January 16, 2003 2:56 PM
Subject: Re: [PEDA] SV: High Voltage power supply


> What's nuts about that?
>
> I had an 800W tesla coil that generated about 18" continuous sparks
> (500kV?).
>
> It was a great party trick, until someone decided to throw a beer can into
> it, shorting the primary to the secondary coil.
>
> The caps have all been appropriated for other HV projects, but I've
re-wound
> a bigger secondary (higher Q) in case I come across some more.
>
> Tom L.
>
>
>
> > -----Original Message-----
> > From: Brian Guralnick [mailto:[EMAIL PROTECTED]]
> > Sent: Friday, 17 January 2003 09:39
> > To: Protel EDA Forum
> > Subject: Re: [PEDA] SV: High Voltage power supply
> >
> >
> > > http://www.kronjaeger.com/hv/
> > This guy is nuts...  Check out his 300KV supply.
> >
> >
> > ____________
> > Brian Guralnick
> > [EMAIL PROTECTED]
> >
> >
> >
> > ----- Original Message -----
> > From: "Tim Exley" <[EMAIL PROTECTED]>
> > To: "'Protel EDA Forum'" <[EMAIL PROTECTED]>
> > Sent: Thursday, January 16, 2003 4:44 PM
> > Subject: Re: [PEDA] SV: High Voltage power supply
> >
> >
> > > As BrianG points out, the answer to your question depends a
> > lot on your
> > > application.  Try searching the web for high voltage
> > supplies ... the
> > > following may offer some starting points ...
> > >
> > > http://www.powerdesigners.com/cgibin/design_center/Subject
> > > http://www.kronjaeger.com/hv/
> > > http://www.high-voltage-assoc.com/cgi-bin/ultimatebb.cgi
> > > http://www.geocities.com/CapeCanaveral/Lab/5322/hv2.html
> > > http://www.epanorama.net/links/psu.html
> > >
> > >
> > >
> > >
> > > -----Original Message-----
> > > From: Brian Guralnick [mailto:[EMAIL PROTECTED]]
> > > Sent: Thursday, 16 January 2003 6:33 p.m.
> > > To: Protel EDA Forum
> > > Subject: Re: [PEDA] SV: High Voltage power supply
> > >
> > >
> > > 8Kv at what current?  Pulsed, or continuous?  How fast
> > doest it need to
> > > build a charge?  I'm thinking along the lines of a small
> > > transformer switched with diode / cap multiplier at the
> > output.  Something
> > > similar to an air ionizer circuit.  You'll need to use
> > > conformal coating all over your PCB.  Will the output be
> > current limited by
> > > a series resistor?
> > >
> > >
> > > ____________
> > > Brian Guralnick
> > > [EMAIL PROTECTED]
> > >
> > >
> > > ----- Original Message -----
> > > From: "Peder K. Hellegaard" <[EMAIL PROTECTED]>
> > > To: "Protel EDA Forum" <[EMAIL PROTECTED]>
> > > Sent: Wednesday, January 15, 2003 5:16 PM
> > > Subject: [PEDA] SV: High Voltage power supply
> > >
> > >
> > > > 8kV is needed......
> > > >
> > > >
> > > >
> > > > -----Oprindelig meddelelse-----
> > > > Fra: Brian Guralnick [mailto:[EMAIL PROTECTED]]
> > > > Sendt: 15. januar 2003 23:03
> > > > Til: Protel EDA Forum
> > > > Emne: Re: [PEDA] High Voltage power supply
> > > >
> > > >
> > > > How high?
> > > >
> > > > 25Kv, 100Kv?
> > > >
> > > > Or, 600v.
> > > >
> > > > In both cases, a flyback will probably be the cheapest & most cost
> > > > effective.
> > > >
> > > >
> > > > ____________
> > > > Brian Guralnick
> > > > [EMAIL PROTECTED]
> > > >
> > > >
> > > > ----- Original Message -----
> > > > From: "Peder K. Hellegaard" <[EMAIL PROTECTED]>
> > > > To: "Protel EDA Forum" <[EMAIL PROTECTED]>
> > > > Sent: Wednesday, January 15, 2003 9:19 AM
> > > > Subject: [PEDA] High Voltage power supply
> > > >
> > > >
> > > > > Anyone who knows where to find schematics for high
> > voltage (low current)
> > > > > power supplies, preferably designed with a series of
> > voltage doublers ?
> > > > >
> > > > >
> > > > > Thanks in advance......
> > > > >
> > > > >
> > > > >
> > > > > Peter
> > > > >
> > > > >
> > > > >
> > > > >
> >

* * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
* To post a message: mailto:[EMAIL PROTECTED]
*
* To leave this list visit:
* http://www.techservinc.com/protelusers/leave.html
*
* Contact the list manager:
* mailto:[EMAIL PROTECTED]
*
* Forum Guidelines Rules:
* http://www.techservinc.com/protelusers/forumrules.html
*
* Browse or Search previous postings:
* http://www.mail-archive.com/proteledaforum@techservinc.com
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * *

Reply via email to