No problem -----Original Message----- From: [email protected] [mailto:[email protected]] On Behalf Of Slau Halatyn Sent: Monday, May 26, 2014 2:09 PM To: [email protected] Subject: Re: Affects on a different track
Hi Papa, Unfortunately, I didn't catch that message. I was out of town and didn't follow the thread. Slau On May 26, 2014, at 4:46 PM, Poppa Bear <[email protected]> wrote: > Hello Slau, would the particular steps to set this up for him be what > I wrote yesterday on this thread? I only say that so he doesn't have > to ask for the steps if what I put was sufficient. Also, thanks for > sharing that command to send all selected tracks to the same send/bus. > > -----Original Message----- > From: [email protected] [mailto:[email protected]] On > Behalf Of Slau Halatyn > Sent: Monday, May 26, 2014 12:42 PM > To: [email protected] > Subject: Re: Affects on a different track > > Hi Chris, > > What you're describing is the normal method for bussing multiple audio > tracks to a single aux input for controlling multiple sources with one > fader. Applying dynamics processing like compression or EQ onto that > aux track is common. However, instantiating a reverb plug-in on that > aux is not very common. First, let me back up just a bit and describe > the first of two scenarios. > > If you have three tracks to which you wish to apply reverb, in the > sends section of each track, route each track to the same bus. On an > aux track with a reverb plug-in, set the input source of that track to the same bus. > There are ways of simplifying this process by choosing to send to an > aux input right from within the contextual menu of the send. This not > only creates an aux input track but automatically uses the next > available bus, automatically sets the aux input to the same bus and > names the bus after the name you give the new aux input track. Sounds > more complicated than it actually is. > > Also, Option-Chisft-clicking on a send will set all selected tracks' > to send to the same bus. > > Ultimately, all tracks are individually sending their signals to the > same bus which is being picked up by the aux input and feeding the > reverb plug-in. The aux fader controls the amount of reverb. In this > scenario, the reverb's wet/dry parameter should be set to 100% wet. > > Normally, overall reverb level is controlled by the aux input track's fader. > Individual reverb levels are controlled by each track's send. In other > words, let's say you were adding reverb to a bunch of instrument > tracks. You might want the percussion tracks to have a bit more reverb > than, say, a violin track which would presumably be more up front. The > violin's send might be turned down a bit or the percussion sends a bit > up. Whichever you choose is simply personal preference. The point is, > the balance between the sends is done with the send levels and the > overall amount of reverb is adjusted with the aux track's fader. > > HTH, > > Slau > > On May 26, 2014, at 3:21 PM, Christopher-Mark Gilland > <[email protected]> wrote: > >> Slau, >> >> You bring up a very good point that raises a question I've now had >> for > several months. I didn't wanna post though in fear of me looking > totally stupid. What I've been doing is to record, say, 3 backing vocal tracks. > Then, I'd take the output path popup button, and instead of leaving it > set on my interface, I'd switch it over to a bus. Let me be very > clear. I'm doing this with the output path selecter, not with the > sends. Now, basically, I then create a stereo auxiliary track, and I > set the input path popup button to the same bus that I set for the > output on the 3 vocal backing tracks. Now, obviously, those 3 backing > vocals are being played through that AUX track. Then, on the AUX > track, I'll pop a reverb, say on insert A. I set it the way I like, > and then those 3 vocals have reverb. The thing is, doing it this way, > if I move my output volume slider within that AUX track up or down, it's going to adjust the volume of those 3 vocals. > So, my question is, what if I didn't want to have that AUX track > contain the vofals. What if all I wanted it to have was the reverb > effect, and nothing more? This way, I could send just the reverb > effect from the 3 vocals to an AUX track, then turn that AUX track up > or down only to increase or decrease the amount of reverb without > screwing with the volume level. How would be the best way to do this > in the example I'm giving? Is this something I'd have to go into the > output window button on the audio tracks? I confess, I've never looked > inside the output window, so I don't totally know what all is in there. Guilty as charged. >> >> Chris. >> >> -- >> You received this message because you are subscribed to the Google >> Groups > "Pro Tools Accessibility" group. >> To unsubscribe from this group and stop receiving emails from it, >> send an > email to [email protected]. >> For more options, visit https://groups.google.com/d/optout. > > -- > You received this message because you are subscribed to the Google > Groups "Pro Tools Accessibility" group. > To unsubscribe from this group and stop receiving emails from it, send > an email to [email protected]. > For more options, visit https://groups.google.com/d/optout. > > -- > You received this message because you are subscribed to the Google Groups "Pro Tools Accessibility" group. > To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. > For more options, visit https://groups.google.com/d/optout. -- You received this message because you are subscribed to the Google Groups "Pro Tools Accessibility" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. For more options, visit https://groups.google.com/d/optout. -- You received this message because you are subscribed to the Google Groups "Pro Tools Accessibility" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. For more options, visit https://groups.google.com/d/optout.
