The monochrome version.
On 12 August 2014 17:17, Ralf Reköndt <[email protected]> wrote: > As you said, having an STE, there only was the way of using the QVME Card. > What have you used up until now? The monochrome software-only version or do > you have an QVME? > > Cheers...Ralf > > ----- Original Message ----- From: "Michael Grunditz" > > >> Derek, >> >> Thats what I do now with a ancient SMSQ/E. But most "modern" programs >> needs GD2, thats why I want to upgrade. >> >> On 12 August 2014 15:35, Derek Stewart <[email protected]> wrote: >>> >>> Hi Michael, >>> >>> The only Atari ST QL Emulator software I have work with added hardware to >>> the Atari, that is; Atari STFM, STF, Mega ST >>> >>> QVME board is added to the Atari TT, STE VME bus >>> >>> From Jochen Merz's web site: >>> >>> SMSQ/E emulates the display in the monochrome 640x400, because this is >>> the >>> only resolution which is greater or equal to the QL's 512x256. You can >>> use >>> the full resolution, even from BASIC. If you require higher resolutions >>> or >>> even higher compatibility, you can use extra hardware which will generate >>> the original QL display organisation in hardware: >>> >>> Original QL-Emulator for the ATARI: only for ST and Mega ST, requires the >>> ZX8301 display chip of the QL. Emulates 512x256 in 4 colours and 256x256 >>> in >>> 8 colours. >>> >>> Extended QL-Emulator: only for ST and Mega ST. Does not require the >>> ZX8301 >>> and gives 512x256 in 4 colours and 768x280 pixels in 4 colours. Can still >>> be >>> connected to original QL monitors. >>> >>> QVME: plugs into the VME bus of the Mega STE and TT. Fully programmable 4 >>> colour modes from 512x256 up to 1280x900 in multiples of 8 pixels. >>> Horizontal and vertical frequencies are programmable too! >>> >>> --- >>> >>> So I guess you could run monochrome 640x400 on the Atari STE in High >>> Resolution mode. >>> >>> Regards, >>> >>> Derek >>> >>> >>> On 12/08/14 14:12, Michael Grunditz wrote: >>>> >>>> >>>> Derek, >>>> >>>> I am using a standard 520STe with 4M ram. >>>> >>>> On 12 August 2014 14:41, Derek Stewart <[email protected]> wrote: >>>>> >>>>> >>>>> HI Michael, >>>>> >>>>> I have a couple of Atari machines, but not used them in a long time. >>>>> >>>>> I have some QL Emulator disks for the Atari ST, I will see if I can get >>>>> them >>>>> off the disks. >>>>> >>>>> What version of emulator hardware do you have. >>>>> >>>>> Regards, >>>>> >>>>> Derek >>>>> >>>>> >>>>> On 12/08/14 09:53, Michael Grunditz wrote: >>>>>> >>>>>> >>>>>> >>>>>> Hi Derek, >>>>>> >>>>>> The problem with the Atari platform is that no recent versions of >>>>>> SMSQ/E works. Does anyone have a binary of the oldest version with >>>>>> GD2? >>>>>> >>>>>> Michael >>>>>> >>>>>> On 12 August 2014 10:40, Derek Stewart <[email protected]> wrote: >>>>>>> >>>>>>> >>>>>>> >>>>>>> Hi Michael, >>>>>>> >>>>>>> There is Menuconfig and Config on Dilwyn's Web site for download. >>>>>>> >>>>>>> The Atari SMSQ/E has PTR_GEN, WMAN, HOT-REXT built into SMSQ/E. So >>>>>>> you >>>>>>> can >>>>>>> not load in a new version of the PTR_GEN. >>>>>>> >>>>>>> An updated version of SMSQ/E from the SMSQ/E web site is required. >>>>>>> >>>>>>> Regards, >>>>>>> >>>>>>> Derek >>>>>>> >>>>>>> >>>>>>> On 11/08/14 20:05, Michael Grunditz wrote: >>>>>>>> >>>>>>>> >>>>>>>> >>>>>>>> >>>>>>>> On 11 August 2014 18:49, gdgqler <[email protected]> wrote: >>>>>>>>> >>>>>>>>> >>>>>>>>> >>>>>>>>> >>>>>>>>> >>>>>>>>> On 11 Aug 2014, at 16:03, Michael Grunditz >>>>>>>>> <[email protected]> >>>>>>>>> wrote: >>>>>>>>> >>>>>>>>>> I am looking for a config tool , menuconfig or the pointer >>>>>>>>>> version. >>>>>>>>>> I >>>>>>>>>> can't even find the plain config program. >>>>>>>>> >>>>>>>>> >>>>>>>>> >>>>>>>>> >>>>>>>>> >>>>>>>>> You could try uconfig from my website gwiltprogs.info. uconfig >>>>>>>>> produces >>>>>>>>> config blocks for BASIC, C and assembler. >>>>>>>> >>>>>>>> >>>>>>>> >>>>>>>> >>>>>>>> >>>>>>>> >>>>>>>> Thank you , the "config" program included works. >>>>>>>> I am fighting Atari SMSQ/E again , and thought that I might >>>>>>>> configure >>>>>>>> the binary. >>>>>>>> It is a PRG file so I think it shouldn't work and it doesn't. >>>>>>>> >>>>>>>> I have also tried to lrespr in a new ptr_gen in order to load a 2.x >>>>>>>> wman. No luck , it seems like I cannot load a new ptr_gen over the >>>>>>>> existing one in SMSQ. >>>>>>>> _______________________________________________ >>>>>>>> QL-Users Mailing List >>>>>>>> http://www.q-v-d.demon.co.uk/smsqe.htm >>>>>>>> >>>>>>> _______________________________________________ >>>>>>> QL-Users Mailing List >>>>>>> http://www.q-v-d.demon.co.uk/smsqe.htm >>>>>> >>>>>> >>>>>> >>>>>> _______________________________________________ >>>>>> QL-Users Mailing List >>>>>> http://www.q-v-d.demon.co.uk/smsqe.htm >>>>>> >>>>> _______________________________________________ >>>>> QL-Users Mailing List >>>>> http://www.q-v-d.demon.co.uk/smsqe.htm >>>> >>>> >>>> _______________________________________________ >>>> QL-Users Mailing List >>>> http://www.q-v-d.demon.co.uk/smsqe.htm >>>> >>> _______________________________________________ >>> QL-Users Mailing List >>> http://www.q-v-d.demon.co.uk/smsqe.htm >> >> _______________________________________________ >> QL-Users Mailing List >> http://www.q-v-d.demon.co.uk/smsqe.htm > > > _______________________________________________ > QL-Users Mailing List > http://www.q-v-d.demon.co.uk/smsqe.htm _______________________________________________ QL-Users Mailing List http://www.q-v-d.demon.co.uk/smsqe.htm
