By the way,, Does a QVME card work in a STE? I am interested in getting one if it works.
On 12 August 2014 17:28, Michael Grunditz <michael.grund...@gmail.com> wrote: > The monochrome version. > > On 12 August 2014 17:17, Ralf Reköndt <ralf.rekoe...@t-online.de> wrote: >> As you said, having an STE, there only was the way of using the QVME Card. >> What have you used up until now? The monochrome software-only version or do >> you have an QVME? >> >> Cheers...Ralf >> >> ----- Original Message ----- From: "Michael Grunditz" >> >> >>> Derek, >>> >>> Thats what I do now with a ancient SMSQ/E. But most "modern" programs >>> needs GD2, thats why I want to upgrade. >>> >>> On 12 August 2014 15:35, Derek Stewart <de...@q40.de> wrote: >>>> >>>> Hi Michael, >>>> >>>> The only Atari ST QL Emulator software I have work with added hardware to >>>> the Atari, that is; Atari STFM, STF, Mega ST >>>> >>>> QVME board is added to the Atari TT, STE VME bus >>>> >>>> From Jochen Merz's web site: >>>> >>>> SMSQ/E emulates the display in the monochrome 640x400, because this is >>>> the >>>> only resolution which is greater or equal to the QL's 512x256. You can >>>> use >>>> the full resolution, even from BASIC. If you require higher resolutions >>>> or >>>> even higher compatibility, you can use extra hardware which will generate >>>> the original QL display organisation in hardware: >>>> >>>> Original QL-Emulator for the ATARI: only for ST and Mega ST, requires the >>>> ZX8301 display chip of the QL. Emulates 512x256 in 4 colours and 256x256 >>>> in >>>> 8 colours. >>>> >>>> Extended QL-Emulator: only for ST and Mega ST. Does not require the >>>> ZX8301 >>>> and gives 512x256 in 4 colours and 768x280 pixels in 4 colours. Can still >>>> be >>>> connected to original QL monitors. >>>> >>>> QVME: plugs into the VME bus of the Mega STE and TT. Fully programmable 4 >>>> colour modes from 512x256 up to 1280x900 in multiples of 8 pixels. >>>> Horizontal and vertical frequencies are programmable too! >>>> >>>> --- >>>> >>>> So I guess you could run monochrome 640x400 on the Atari STE in High >>>> Resolution mode. >>>> >>>> Regards, >>>> >>>> Derek >>>> >>>> >>>> On 12/08/14 14:12, Michael Grunditz wrote: >>>>> >>>>> >>>>> Derek, >>>>> >>>>> I am using a standard 520STe with 4M ram. >>>>> >>>>> On 12 August 2014 14:41, Derek Stewart <de...@q40.de> wrote: >>>>>> >>>>>> >>>>>> HI Michael, >>>>>> >>>>>> I have a couple of Atari machines, but not used them in a long time. >>>>>> >>>>>> I have some QL Emulator disks for the Atari ST, I will see if I can get >>>>>> them >>>>>> off the disks. >>>>>> >>>>>> What version of emulator hardware do you have. >>>>>> >>>>>> Regards, >>>>>> >>>>>> Derek >>>>>> >>>>>> >>>>>> On 12/08/14 09:53, Michael Grunditz wrote: >>>>>>> >>>>>>> >>>>>>> >>>>>>> Hi Derek, >>>>>>> >>>>>>> The problem with the Atari platform is that no recent versions of >>>>>>> SMSQ/E works. Does anyone have a binary of the oldest version with >>>>>>> GD2? >>>>>>> >>>>>>> Michael >>>>>>> >>>>>>> On 12 August 2014 10:40, Derek Stewart <de...@q40.de> wrote: >>>>>>>> >>>>>>>> >>>>>>>> >>>>>>>> Hi Michael, >>>>>>>> >>>>>>>> There is Menuconfig and Config on Dilwyn's Web site for download. >>>>>>>> >>>>>>>> The Atari SMSQ/E has PTR_GEN, WMAN, HOT-REXT built into SMSQ/E. So >>>>>>>> you >>>>>>>> can >>>>>>>> not load in a new version of the PTR_GEN. >>>>>>>> >>>>>>>> An updated version of SMSQ/E from the SMSQ/E web site is required. >>>>>>>> >>>>>>>> Regards, >>>>>>>> >>>>>>>> Derek >>>>>>>> >>>>>>>> >>>>>>>> On 11/08/14 20:05, Michael Grunditz wrote: >>>>>>>>> >>>>>>>>> >>>>>>>>> >>>>>>>>> >>>>>>>>> On 11 August 2014 18:49, gdgqler <grggw...@gmail.com> wrote: >>>>>>>>>> >>>>>>>>>> >>>>>>>>>> >>>>>>>>>> >>>>>>>>>> >>>>>>>>>> On 11 Aug 2014, at 16:03, Michael Grunditz >>>>>>>>>> <michael.grund...@gmail.com> >>>>>>>>>> wrote: >>>>>>>>>> >>>>>>>>>>> I am looking for a config tool , menuconfig or the pointer >>>>>>>>>>> version. >>>>>>>>>>> I >>>>>>>>>>> can't even find the plain config program. >>>>>>>>>> >>>>>>>>>> >>>>>>>>>> >>>>>>>>>> >>>>>>>>>> >>>>>>>>>> You could try uconfig from my website gwiltprogs.info. uconfig >>>>>>>>>> produces >>>>>>>>>> config blocks for BASIC, C and assembler. >>>>>>>>> >>>>>>>>> >>>>>>>>> >>>>>>>>> >>>>>>>>> >>>>>>>>> >>>>>>>>> Thank you , the "config" program included works. >>>>>>>>> I am fighting Atari SMSQ/E again , and thought that I might >>>>>>>>> configure >>>>>>>>> the binary. >>>>>>>>> It is a PRG file so I think it shouldn't work and it doesn't. >>>>>>>>> >>>>>>>>> I have also tried to lrespr in a new ptr_gen in order to load a 2.x >>>>>>>>> wman. No luck , it seems like I cannot load a new ptr_gen over the >>>>>>>>> existing one in SMSQ. >>>>>>>>> _______________________________________________ >>>>>>>>> QL-Users Mailing List >>>>>>>>> http://www.q-v-d.demon.co.uk/smsqe.htm >>>>>>>>> >>>>>>>> _______________________________________________ >>>>>>>> QL-Users Mailing List >>>>>>>> http://www.q-v-d.demon.co.uk/smsqe.htm >>>>>>> >>>>>>> >>>>>>> >>>>>>> _______________________________________________ >>>>>>> QL-Users Mailing List >>>>>>> http://www.q-v-d.demon.co.uk/smsqe.htm >>>>>>> >>>>>> _______________________________________________ >>>>>> QL-Users Mailing List >>>>>> http://www.q-v-d.demon.co.uk/smsqe.htm >>>>> >>>>> >>>>> _______________________________________________ >>>>> QL-Users Mailing List >>>>> http://www.q-v-d.demon.co.uk/smsqe.htm >>>>> >>>> _______________________________________________ >>>> QL-Users Mailing List >>>> http://www.q-v-d.demon.co.uk/smsqe.htm >>> >>> _______________________________________________ >>> QL-Users Mailing List >>> http://www.q-v-d.demon.co.uk/smsqe.htm >> >> >> _______________________________________________ >> QL-Users Mailing List >> http://www.q-v-d.demon.co.uk/smsqe.htm _______________________________________________ QL-Users Mailing List http://www.q-v-d.demon.co.uk/smsqe.htm
