Second approach, then, is what *hubs* might fit the Fiesta Mk2 suspension struts and ball-joint? I'm wondering about a later Fiesta, Escort, or maybe even Focus hub? I'm looking for something that will accept a bigger brake calliper and disk in a 15" wheel, and I'm really not au fait with Ford bits and bobs... The driveshaft is not an issue, since I'm making one up anyway to meet the Fiat flanges.
Neil On 13 July, 15:35, Jim Hearne <[email protected]> wrote: > I didn't think anything else fitted in the Fiesta hub carrier. > Is there a part number on the hub casting ? > > Unfortunately Microcat doesn't list the splines for Escort parts. > > Jim > > On 13/07/2010 15:30, barnacle wrote: > > > So as I have 24 splines, it's definitely not a Fiesta. Wonder what it > > might be? > > > On 13 July, 11:02, Jim Hearne<[email protected]> wrote: > > >> The earlier smaller engined Mk2 Fiestas had 22 splines on the outer > >> driveshaft joint and the bigger engined had 23 splines. > >> The hub and the bearings are different sizes for this as well but the > >> hub carrier is the same. > > >> I think the Mk2 balljoints should be bent, i can't remember now for sure > >> though, need to look under a Quantum. > >> The others could be Mk1 > >> All Mk3 fiestas i remember have 3 bolt fixing (or usually rivets) on the > >> balljoint. > > >> Jim > > >> On 13/07/2010 10:49, barnacle wrote: > > >>> While changing the bearings and CV joints it became apparent that > >>> while the engine is definitely XR2, the hubs aren't... Joe's suppliers > >>> are investigating the CV joint and from the spline count (24 on the > >>> outer and 23 on the inner) it's apparent that it's not a Fiesta hub. > >>> The fact that it locked the XR2 bearings up is a good indicator there, > >>> too. > > >>> The ball joints originally supplied were larger than those fitted, and > >>> were straight: ____| while those we removed were bent: ____\ - again > >>> according to the supplier, the first type were XR2 and the second XR2i > >>> (so Fiesta MK3). It also seems that the brake disks - represented as > >>> XR2 but not guaranteed - have a different offset from those fitted. > > >>> So it looks as if we may have something from an Escort in there... > > >>> The plan is to replace the existing 13" wheels with something with > >>> room for larger brakes, and to better match the size of the tyres to > >>> the Coupe's (the 13s are 10% smaller rolling radius). Any hints as to > >>> what hubs these might be, or with which hubs we might replace them to > >>> accommodate the larger brakes, would be gratefully accepted. > > >>> Ta, > > >>> Neil > > >>> p.s. Joe has started scouring eBay for a Quantum to convert for > >>> himself, he enjoyed it so much! > > >>> p.p.s I'm investigating the spring rate of the existing springs; > >>> they'll need uprating to get the ride height back where it should be. > >>> Might need new shocks, too; we'll see what the bounce period is. > >>> Anyone know what the compression for the 2+2 'special' front springs > >>> is in lbs/in? -- You received this message because you are subscribed to the Google Groups "Quantum Owners Group" group. To post to this group, send email to [email protected] To unsubscribe from this group, send email to [email protected] For more options, visit this group at http://groups.google.com/group/quantumowners?hl=en IMPORTANT NOTE: All information presented herewith is provided on an "As Is" basis, without warranty or the implication thereof. Neither the Quantum Owners Club nor the individuals associated with the Quantum Owners Club or in the preparation of the above information shall have any liability to any person or entity with respect to liability, loss, or damage caused or alleged to be caused directly or indirectly by the instructions contained within this or related message(s).
