WRT #3:

On my Beauford I was even required to label all controls for the heater - I used a Tipex pen on the handles - and to have the requisite symbols for all of the switches PLUS a tell-tale light on each switch that was "clearly visible" from the driver's eye position. I had the rear fog and rear heated screen switches under the dash and this was a definite No-No!, so I had to cut into my otherwise artistically balanced wooden dash to mount them within hand reach.

I did become quite adept at dismantling the Sierra switches and replacing the internal tell-tale bulbs after three had failed the test even though they were actually working! Halfords sell a miniature green bulb that is ideal for the purpose. The originals were standard white bulbs with a green plastic coating that did not readily come off without splitting. Luckily the LEDs do not tend to fail.

If you are using the switch block from Car Builders Solutions or Stafford Vehicle Spare (whatever), these meet the requirements as they already have the symbols and tell-tale lights installed.

There is a parts company that sells transfers for the requisite symbols for about £12 a sheet (Ouch!), which I am informed are IVA compliant. Sorry but I have not bought any, only seen a sheet at a former work colleague's house some time ago - should be found by Google? Probably Car Builders Solutions. I do have a DOT 3 image .pdf if you do not already have one though it might take some finding as I have swapped PCs of late and it is probably stored in an email not on this machine.

The issue of rear fog lamps only coming on with headlights has been mentioned elsewhere. I also could not find a simple solution and had to use another relay for this operation.

#4:
It is necessary to balance the air flow on twin carburettors before undertaking any other adjustments or you will have unbalanced power from the front and rear cylinders. This can be done with either a depression type meter - basically a Venturi couple to a water manometer (very easy to make but do use a water trap in the line to the manometer to avoid pulling water into the engine if the depression is initially too high for the manometer!), which is held onto each carb in turn or a vane type which shows a displacement on an arbitrary scale according to the airflow. Various people have these within the group including myself. Where are you? I am at Shoreham by Sea on the South coast near Brighton if that is of any help.

Once the airflow is balanced and the physical components in each carb are the same then the engine should run acceptably even though there may be a need for some tweaking of the operation of second throttle opening point and accelerator pumps still to be undertaken if mechanical rather than vacuum operated.

Hope this helps,

Hamish

-----Original Message----- From: Ian Mac
Sent: Wednesday, March 09, 2011 11:51 PM
To: Quantum Owners Group
Subject: [Quantum Owners] Xtreme Heading for IVA- at last


It has been a long time since I posted on the Group, but I have nearly
completed the build of the Xtreme that I bought ("almost ready for
SVA/ IVA") back in May 2009 and just wnted to say hello again and ask
a couple of questions to anyone who has gone through IVA with an
Xtreme.
I also need to get my QOC membership renewed as I do not think that I
renewed it last year as I have not received any information for a long
time  (I also noted that the sums shown on the web site are different
from those on the Application form downloaded freom site):

1. I am not sure if I need to add indicators to the wheel arches for
visibility.  They were not needed for SVA when I did the last car, but
I know that some peope have been fitting them now.

2. What did people do to get round the problem of sharp edges on the
boot hinges as I am struggling to do something that looks permanent
and reasonable.

3. For Identification of controls, etc do you need to have indication
lights labelled: main beam, indicators, ignition/ oil?

4. Has anyone had issue with the brake balance front and rear as I
have read other kit cars failing due to the balance front to rear
being incorrect?

Finally, I am about to try and set up the weber 40's on the car as the
car does nto run well at the moment.  THe jets/ tubes, etc are correct
for the engine size of 1.8, but I wanted to know peoples experinece
with setting the carbs up.  Do you need to have the air balancing
meter to set them up correctly or can this be done another way without
the expense of buying the air flow meter?

Once I get a date for IVA inspection, I will keep you informed as to
how the test went

Regards,

Ian Mac

Xtreme 059

--
You received this message because you are subscribed to the Google Groups "Quantum Owners Group" group.
To post to this group, send email to [email protected]
To unsubscribe from this group, send email to [email protected] For more options, visit this group at http://groups.google.com/group/quantumowners?hl=en

IMPORTANT NOTE: All information presented herewith is provided on an "As Is" basis, without warranty or the implication thereof. Neither the Quantum Owners Club nor the individuals associated with the Quantum Owners Club or in the preparation of the above information shall have any liability to any person or entity with respect to liability, loss, or damage caused or alleged to be caused directly or indirectly by the instructions contained within this or related message(s).




--
You received this message because you are subscribed to the Google Groups "Quantum 
Owners Group" group.
To post to this group, send email to [email protected]
To unsubscribe from this group, send email to 
[email protected]
For more options, visit this group at 
http://groups.google.com/group/quantumowners?hl=en

IMPORTANT NOTE: All information presented herewith is provided on an "As Is" 
basis, without warranty or the implication thereof. Neither the Quantum Owners Club nor 
the individuals associated with the Quantum Owners Club or in the preparation of the 
above information shall have any liability to any person or entity with respect to 
liability, loss, or damage caused or alleged to be caused directly or indirectly by the 
instructions contained within this or related message(s).

Reply via email to