heres a pic of how i have it plumbed in (top) and how i now believe it should be (bottom)
http://i120.photobucket.com/albums/o192/jindal/2012%20quantum/IMG_20130107_062518_zps57c7d391.jpg On Jan 7, 3:13 pm, jin <[email protected]> wrote: > I'm intrigued too mate > > we shall see > > watch this space..... > > On Jan 7, 1:18 pm, "Jim Hearne" <[email protected]> wrote: > > > > > I'm intrigued as to what this problem is going to turn out to be. > > > As soon as one of the heater hoses was removed there should be water running > > out regardless of the direction or types of T, Y etc. > > When i think of all the strange arrangements of plumbing I've used in the > > past and had no problems, i can't believe it's just that. > > > You'd have to have the heater matrix completely block to stop any water, a > > bit or debris isn't going to do that. > > Unless it's been made wrong. > > > Jim > > > -----Original Message----- > > From: jin > > Sent: Monday, January 07, 2013 12:45 PM > > To: Quantum Owners Group > > Subject: [Quantum Owners] Re: 1.6 CVH Heater coolant pipes > > > cheers for the reply > > > Jim > > the inlet manifold is new and unblocked along with the hose union > > underneath, the matrix is new and so is the pump, the stat housing was > > removed and replaced a month ago when i swapped the stat for a warmer > > one, i know this flows fine as there is a steady stream from the top > > bleed hose back to the reservoir > > > ive looked more in depth at how ive got the Y piece plumed in now and > > also how i had the T plumed in before, and bearing in mind there are 2 > > flows in and 1 flow out from the Y i have got it so the manifold flows > > against the flow from the pump and heater, so ill re - jiggle this and > > at the same time when ive got the heater hoses off the matrix ill > > check that, although its new im thinking a bit of debris may have made > > its way in, but my hopes are pinned on repositioning the Y piece, as > > above post, ive got all hoses warm and the elbows i fitted just off > > the matrix are transparent, i can see there is no coolant in there at > > all but there is further down the hose as they are warm > > ill take a look and get back, could be a while though as ive got new > > struts going on at the mo > > > On Jan 7, 9:02 am, "Jim Hearne" <[email protected]> wrote: > > > Airlocks aren t normal on the Mk2 Fiesta/Quantum. > > > I ve always just filled them up and run the engine topping up the > > > reservoir if need be until the stat opens. > > > > I can t think why Jin would have no water at all at the heater, it should > > > flow out under gravity from both pipes. > > > > I m sure you already checked Jin, or used new parts, but, are you sure > > > that the outlet from the inlet manifold and the outlet from the stat > > > housing are clear ? > > > They can corrode up. > > > > Jim > > > > From: Alan > > > Sent: Monday, January 07, 2013 12:41 AM > > > To: [email protected] > > > Subject: Re: [Quantum Owners] 1.6 CVH Heater coolant pipes > > > > If it comes up from the alternator yeup that's the electric autochoke > > > wire. I'd keep the coolant pipes round the carb though, bit of warmth > > > might help prevent carb icing/help in cold spells. > > > > Slightly worried about changing my leaky heater matrix now if I risk > > > losing all heat.. > > > > On Thursday, January 3, 2013 7:33:49 PM UTC, Keith Joseph wrote: > > > > Thanks for that, it looks like a really useful website. I can see me > > > spending lots of time (and money!) on that site. > > > > As regards the autochoke, I really don't know / can't remember as it was > > > taken off at least 10 years ago now. I can only assume that it was > > > electrical now that you have pointed out that the hose from the Y piece is > > > required for the inlet manifold. I seem to remember that there is a single > > > wire which has been redundant for many years - I'll bet that was the wire > > > leading to the original choke. > > > > Cheers, > > > > Keith > > > > On Thursday, 3 January 2013 19:16:30 UTC, AJ wrote: > > > Our local Motor Factor is very friendly and sells lenghts of hose by > > > the metre - I just take a sample of the old one in and they match.... > > > > The following web site is useful for > > > ideas -http://www.cbsonline.co.uk/ > > > > On the Carb.... > > > Did you have a hot water heated Autochoke or was it Electrical? > > > > The hot water Autochoke had a water inlet tube and an outlet tube. > > > The old manual conversion kits usually included a short connecting > > > tube (and clips) to allow the autochoke to be bypassed > > > > I had an electricaly heated Autochoke which I converted - the Y piece > > > is still required as I believe it controls the temperature of the "inlet > > > manifold" > > > > ----- Original Message ----- > > > From: > > > Sent: Thursday, January 03, 2013 6:48 PM > > > Subject: [Quantum Owners] 1.6 CVH Heater coolant pipes > > > > Hi and Happy New Year to one and all. > > > > I'm after a bit of advice regarding coolant pipework on my 2+2. > > > > I have a problem whereby I cannot seam to get any real heat into the > > > cabin through the heater. (I've had this problem for several years but > > > it's finally got to the top of the list of jobs!) > > > > I have flushed the system out thoroughly and have just replaced the > > > thermostat which opens as it should. I think I have traced the problem to > > > the short hose which is connected to the "Y" Piece and goes over the large > > > metal bar and onto the top of the heater matrix connection on the > > > bulkhead. I think the rubber hose has seen better days and is simply not > > > allowing enough hot water to pass through it into the heater matrix. > > > > I have started looking for a replacement hose but am struggling to > > > find one - Does anybody know where I can get one from / what the correct > > > name for this small pipe is? > > > > Also, as I have a manual choke on my carb, can anyone advise if I > > > still need to retain the hot water supply to the bottom of the carb (Weber > > > VV), or can I simply remove this pipe and therefore get rid of the "Y" > > > piece also? > > > > Many thanks for your help. > > > > Cheers, > > > > Keith > > > > -- > > > You received this message because you are subscribed to the Google > > > Groups "Quantum Owners Group" group. > > > To post to this group, send email to [email protected] > > > To unsubscribe from this group, send email to > > > [email protected] > > > For more options, visit this group > > > athttp://groups.google.com/group/quantumowners?hl=en > > > > IMPORTANT NOTE: All information presented herewith is provided on an > > > "As Is" basis, without warranty or the implication thereof. Neither the > > > Quantum Owners Club nor the individuals associated with the Quantum Owners > > > Club or in the preparation of the above information shall have any > > > liability to any person or entity with respect to liability, loss, or > > > damage caused or alleged to be caused directly or indirectly by the > > > instructions contained within this or related message(s). > > > -- > > > You received this message because you are subscribed to the Google Groups > > > "Quantum Owners Group" group. > > > To post to this group, send email to [email protected] > > > To unsubscribe from this group, send email to > > > [email protected] > > > For more options, visit this group > > > athttp://groups.google.com/group/quantumowners?hl=en > > > > IMPORTANT NOTE: All information presented herewith is provided on an "As > > > Is" basis, without warranty or the implication thereof. Neither the > > > Quantum Owners Club nor the individuals associated with the Quantum Owners > > > Club or in the preparation of the above information shall have any > > > liability to any person or entity with respect to liability, loss, or > > > damage caused or alleged to be caused directly or indirectly by the > > > instructions contained within this or related message(s).- Hide quoted > > > text - > > > > - Show quoted text - > > > -- > > You received this message because you are subscribed to the Google Groups > > "Quantum Owners Group" group. > > To post to this group, send email to [email protected] > > To unsubscribe from this group, send email to > > [email protected] > > For more options, visit this group > > athttp://groups.google.com/group/quantumowners?hl=en > > > IMPORTANT NOTE: All information presented herewith is provided on an "As Is" > > basis, without warranty or the implication thereof. Neither the Quantum > > Owners Club nor the individuals associated with the Quantum Owners Club or > > in the preparation of the above information shall have any liability to any > > person or entity with respect to liability, loss, or damage caused or > > alleged to be caused directly or indirectly by the instructions contained > > within this or related message(s).- Hide quoted text - > > > - Show quoted text - -- You received this message because you are subscribed to the Google Groups "Quantum Owners Group" group. To post to this group, send email to [email protected] To unsubscribe from this group, send email to [email protected] For more options, visit this group at http://groups.google.com/group/quantumowners?hl=en IMPORTANT NOTE: All information presented herewith is provided on an "As Is" basis, without warranty or the implication thereof. Neither the Quantum Owners Club nor the individuals associated with the Quantum Owners Club or in the preparation of the above information shall have any liability to any person or entity with respect to liability, loss, or damage caused or alleged to be caused directly or indirectly by the instructions contained within this or related message(s).
